• CSA Z15001 : 2012

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    ANAESTHETIC AND RESPIRATORY EQUIPMENT - COMPATIBILITY WITH OXYGEN

    Available format(s):  Hardcopy, PDF

    Superseded date:  10-12-2020

    Language(s):  English, French

    Published date:  01-01-2017

    Publisher:  Canadian Standards Association

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Cleanliness
    5 Resistance to ignition
    6 Risk management
    Annex A (informative) - Examples of cleaning
            procedures
    Annex B (informative) - Typical methods for
            validation of cleaning procedures
    Annex C (informative) - Design considerations
    Annex D (informative) - Selection of materials
    Annex E (informative) - Recommended method for
            combustion and quantitative analysis of
            combustion products of non-metallic
            materials
    Annex F (informative) - Rationale
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes requirements for the oxygen compatibility of materials, components and devices for anaesthetic and respiratory applications, which can come into contact with oxygen in normal condition or in single fault condition at gas pressures greater than 50 kPa.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Product Note Reconfirmed EN
    Publisher Canadian Standards Association
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 4589-3:2017 Plastics Determination of burning behaviour by oxygen index Part 3: Elevated-temperature test
    ISO 11114-1:2012 Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materials
    IEC 60601-1:2005+AMD1:2012 CSV Medical electrical equipment - Part 1: General requirements for basic safety and essential performance
    ISO 10298:2010 Determination of toxicity of a gas or gas mixture
    ASTM G 88 : 2013 : REDLINE Standard Guide for Designing Systems for Oxygen Service
    ASTM G 122 : 1996 Standard Test Method for Evaluating the Effectiveness of Cleaning Agents
    NFPA 53 : 2016 MATERIALS, EQUIPMENT, AND SYSTEMS USED IN OXYGEN-ENRICHED ATMOSPHERES
    ASTM G 72 : 2001 Standard Test Method for Autogenous Ignition Temperature of Liquids and Solids in a High-Pressure Oxygen-Enriched Environment
    ISO 11114-3:2010 Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 3: Autogenous ignition test for non-metallic materials in oxygen atmosphere
    BS 6869(1987) : 1987 CODE OF PRACTICE FOR PROCEDURES FOR ENSURING THE CLEANLINESS OF INDUSTRIAL PROCESS MEASUREMENT AND CONTROL EQUIPMENT IN OXYGEN SERVICE
    ISO 21969:2009 High-pressure flexible connections for use with medical gas systems
    ASTM G 114 : 2014 : REDLINE Standard Practices for Evaluating the Age Resistance of Polymeric Materials Used in Oxygen Service
    ISO 10297:2014 Gas cylinders Cylinder valves Specification and type testing
    ISO 7291:2010 Gas welding equipment Pressure regulators for manifold systems used in welding, cutting and allied processes up to 30 MPa (300 bar)
    ASTM G 175 : 2013 : REDLINE Standard Test Method for Evaluating the Ignition Sensitivity and Fault Tolerance of Oxygen Pressure Regulators Used for Medical and Emergency Applications
    ISO 10524-3:2005 Pressure regulators for use with medical gases Part 3: Pressure regulators integrated with cylinder valves
    ASTM G 131 : 1996 Standard Practice for Cleaning of Materials and Components by Ultrasonic Techniques
    ASTM G 127 : 2015 : REDLINE Standard Guide for the Selection of Cleaning Agents for Oxygen-Enriched Systems
    EN 13448:2001+A1:2009 AGRICULTURAL AND FORESTRY MACHINERY - INTER-ROW MOWING UNITS - SAFETY
    ASTM G 86 : 1998 : REV A Standard Test Method for Determining Ignition Sensitivity of Materials to Mechanical Impact in Ambient Liquid Oxygen and Pressurized Liquid and Gaseous Oxygen Environments
    ASTM G 4 : 2001 Standard Guide for Conducting Corrosion Tests in Field Applications
    ASTM G 63 : 2015 : REDLINE Standard Guide for Evaluating Nonmetallic Materials for Oxygen Service
    ISO 4589-2:2017 Plastics Determination of burning behaviour by oxygen index Part 2: Ambient-temperature test
    ISO 4135:2001 Anaesthetic and respiratory equipment Vocabulary
    ISO 10524-1:2006 Pressure regulators for use with medical gases Part 1: Pressure regulators and pressure regulators with flow-metering devices
    ASTM G 74 : 2013 : REDLINE Standard Test Method for Ignition Sensitivity of Nonmetallic Materials and Components by Gaseous Fluid Impact
    CGA V 9 : 2012 COMPRESSED GAS CYLINDER VALVES
    ISO 19701:2013 Methods for sampling and analysis of fire effluents
    ISO 4589-1:2017 Plastics Determination of burning behaviour by oxygen index Part 1: General requirements
    ASTM G 120 : 2015 : REDLINE Standard Practice for Determination of Soluble Residual Contamination by Soxhlet Extraction
    ISO 10524-2:2005 Pressure regulators for use with medical gases Part 2: Manifold and line pressure regulators
    ASTM G 126 : 2016 : REDLINE Standard Terminology Relating to the Compatibility and Sensitivity of Materials in Oxygen Enriched Atmospheres
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective