• There are no items in your cart

DD CEN/TS 13001-3-1 : 2004

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

CRANES - GENERAL DESIGN - PART 3-1: LIMIT STATES AND PROOF OF COMPETENCE OF STEEL STRUCTURES
Available format(s)

Hardcopy , PDF

Superseded date

11-30-2012

Language(s)

English

Published date

01-01-2004

Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 General
  4.1 Materials
      4.1.1 Structural members
      4.1.2 Connecting devices
  4.2 Bolt connections
      4.2.1 General
      4.2.2 Shear and bearing connections
      4.2.3 Slip resistant connections
      4.2.4 Connections loaded in tension
  4.3 Pin connections
  4.4 Welded connections
  4.5 Proofs of structural members and connections
5 Proof of static strength
  5.1 General
  5.2 Limit design stresses and forces
      5.2.1 General
      5.2.2 Limit design stress in structural members
      5.2.3 Limit design forces in bolt connections
      5.2.4 Limit design forces in pins
      5.2.5 Limit design stresses in welded connections
  5.3 Execution of the proof
      5.3.1 Proof for structural members
      5.3.2 Proof for bolt connections
      5.3.3 Proof for pin connections
      5.3.4 Proof for welded connections
6 Proof of fatigue strength
  6.1 General
  6.2 Limit design stresses
      6.2.1 Characteristic values of the stress range
      6.2.2 Weld quality
      6.2.3 Effect of test loads
      6.2.4 Requirements for fatigue testing
  6.3 Classes S of stress history parameter s
      6.3.1 Simplified method based on service conditions
      6.3.2 Selection based on experience
  6.4 Execution of the proof
  6.5 Determination of the permissible stress range
      6.5.1 Applicable methods
      6.5.2 Direct use of stress history parameter
      6.5.3 Use of class S
7 Proof of static strength of hollow section girder joints
8 Proof of elastic stability
Annex A (normative) Values of inverse slope of sigma/N-curve
                       m and permissible stress range delta
                       sigma[c], delta tau[c]
Annex B (informative) Guidance for selection of classes S due
                       to experience
Annex C (normative) Calculated values of permissible stress
                       range delta sigma[Rd]
Annex D (normative) Design weld stress sigma[W,Sd] and
                       tau[W,Sd]
  D.1 Butt joint
  D.2 Fillet weld and groove weld with uniform distributed
      load
  D.3 Relevant distribution length under punctiform load
Annex E (informative) Hollow Sections
Annex F (informative) Selection of a suitable set of crane
                       standards for a given application
Bibliography

Describes general conditions, requirements and methods to prevent mechanical hazards of cranes by design and theoretical verification.

Committee
MHE/3/1
DocumentType
Draft
Pages
76
PublisherName
British Standards Institution
Status
Superseded
SupersededBy

Standards Relationship
CEN/TS 13001-3-1:2004/AC:2006 Identical

EN 10113-2 : 1993 HOT-ROLLED PRODUCTS IN WELDABLE FINE GRAIN STRUCTURAL STEELS - DELIVERY CONDITIONS FOR NORMALIZED/NORMALIZED ROLLED STEELS
ISO 2553:2013 Welding and allied processes Symbolic representation on drawings Welded joints
EN 10149-1:2013 Hot rolled flat products made of high yield strength steels for cold forming - Part 1: General technical delivery conditions
ISO 4306-1:2007 Cranes — Vocabulary — Part 1: General
EN 10164:2004 Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions
EN 10149-2:2013 Hot rolled flat products made of high yield strength steels for cold forming - Part 2: Technical delivery conditions for thermomechanically rolled steels
EN 10025:1990/A1:1993 HOT ROLLED PRODUCTS OF NON-ALLOY STRUCTURAL STEELS - TECHNICAL DELIVERY CONDITIONS
EN 12345 : 1998 WELDING - MULTILINGUAL TERMS FOR WELDED JOINTS WITH ILLUSTRATIONS
ISO 9013:2017 Thermal cutting — Classification of thermal cuts — Geometrical product specification and quality tolerances
API 2A : 1986 RECOMMENDED PRACTICE FOR PLANNING, DESIGNING AND CONSTRUCTING FIXED OFFSHORE PLATFORMS
EN 10045-1 : 1990 METALLIC MATERIALS - CHARPY IMPACT TEST - PART 1: TEST METHOD
ISO 5817:2014 Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections
EN 10137-2 : 1995 PLATES AND WIDE FLATS MADE OF HIGH YIELD STRENGTH STRUCTURAL STEELS IN THE QUENCHED AND TEMPERED OR PRECIPITATION HARDENED CONDITIONS - DELIVERY CONDITIONS FOR QUENCHED AND TEMPERED STEELS
EN 13001-2:2014 Crane safety - General design - Part 2: Load actions
EN 10113-1 : 1993 HOT ROLLED PRODUCTS IN WELDABLE FINE GRAIN STRUCTURAL STEELS - GENERAL DELIVERY CONDITIONS
EN ISO 12100-1:2003/A1:2009 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY
EN 13001-1:2015 Cranes - General design - Part 1: General principles and requirements
EN 22553:1994 Welded, brazed and soldered joints - Symbolic representation on drawings (ISO 2553:1992)
ISO 12100-2:2003 Safety of machinery Basic concepts, general principles for design Part 2: Technical principles
EN ISO 12100-2:2003/A1:2009 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES
ISO 286-2:2010 Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
EN ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013)
ISO 12100-1:2003 Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology
1998/37/EC : 1998 DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 22 JUNE 1998 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO MACHINERY
EN ISO 9013:2017 Thermal cutting - Classification of thermal cuts - Geometrical product specification and quality tolerances (ISO 9013:2017)
EN 1070 : 1998 SAFETY OF MACHINERY - TERMINOLOGY
EN 10149-3:2013 Hot rolled flat products made of high yield strength steels for cold forming - Part 3: Technical delivery conditions for normalized or normalized rolled steels
EN 25817 : 1992 ARC WELDED JOINTS IN STEEL - GUIDANCE ON QUALITY LEVELS FOR IMPERFECTIONS
EN 1993-1-1:2005/A1:2014 EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS
ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread
EN 10113-3 : 1993 HOT ROLLED PRODUCTS IN WELDABLE FINE GRAIN STRUCTURAL STEELS - DELIVERY CONDITIONS FOR THERMOMECHANICAL ROLLED STEELS

View more information
US$335.40
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.