• There are no items in your cart

DEFSTAN 02-304(PT2)/2(2002) : 2002

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

SHAFTING SYSTEMS AND PROPULSORS - PART 2: DESIGN REQUIREMENTS FOR MAIN PROPULSION SHAFTING AUXILIARIES
Superseded date

10-19-2015

Published date

01-12-2013

TITLE PAGE
SCOPE
FOREWORD
Sponsorship
Conditions of Release
Categories of Defence Standard
Related Documents
Health and Safety
Additional Information
CONTENTS
SECTION 1 - PERFORMANCE SPECIFICATION
SECTION 2 - NATIONAL/INTERNATIONAL REGULATIONS
SECTION 3 - MILITARY STANDARDS/REQUIREMENTS
            3.1 Environmental Conditions
            3.2 Drawings
            3.3 Materials
            3.4 Manufacture, Installation and Trials
                3.4.1 General
                3.4.2 Welding
                3.4.3 Seating
                3.4.4 Limits and Fits
                3.4.5 Finish
                3.4.6 Marking
                3.4.7 Testing
                3.4.8 Installation
                3.4.9 Trials
SECTION 4 - DESIGN REQUIREMENTS/GUIDANCE
            4.1 Main Shaft Bearings
                4.1.1 General
                4.1.2 Stern Tube and Bracket Bearing Barrels
                4.1.3 Stern Tube and Bracket Bearing Bushes
                4.1.4 Stern Tube and Bracket Bearings - Preferred
                       Types and Materials
                4.1.5 Alternative Bearing Materials
                4.1.6 Bearing Length/Diameter Ratio
                4.1.7 Bearing Pressures
                4.1.8 Bearing Clearance
                4.1.9 Lubrication
                4.1.10 Plummer Bearings - General
                4.1.11 Seatings
                4.1.12 Plummer Bearing Types
                4.1.13 Design Requirements
            4.2 Design Requirements - Bulkhead Glands
                4.2.1 General
                4.2.2 HM Surface Ships
                4.2.3 Submarines
            4.3 Stern Seals
                4.3.1 General
                4.3.2 General Design Requirements
                4.3.3 Design Requirements for HM Surface
                      Ship Stern Seals
                4.3.4 Design Requirements for Submarine
                      Stern Seals
                4.3.5 Design Requirements for Soft Packed
                      Glands
            4.4 Shaft Brake and Locking Gear
                4.4.1 Shaft Brake General
                4.4.2 Design Requirements
                4.4.3 Shaft Locking Gear - General
                4.4.4 Design Requirements
            4.5 Thrust Block Bearings
                4.5.1 General
                4.5.2 Seatings
                4.5.3 Design Requirements
                4.5.4 Thrustmeter/Resonance Changer
                4.5.5 Trailing Thrust Bearing
            4.6 Thrustmeters
            4.7 Resonance Changers
                4.7.1 General
                4.7.2 Design Procedure
            4.8 Shaft Earthing and Cathodic Protection Devices
                4.8.1 General
                4.8.2 Interface Requirements
            4.9 Shaft Interface for Shaft Driven Auxiliaries
                4.9.1 General
                4.9.2 Design Requirements
SECTION 5 - CORPORATE KNOWLEDGE AND EXPERIENCE
            5.1 Special Service Air Transfer Box
                5.1.1 General
                5.1.2 Design Requirements
                5.1.3 Design Information
ANNEX A - RELATED DOCUMENTS
ANNEX B - ABBREVIATIONS AND DEFINITIONS
ANNEX C - PROCUREMENT CHECK LIST
ALPHABETICAL INDEX

Defines the design requirements for shafting auxiliaries fitted in HM Surface Ships and Submarines.

DevelopmentNote
Supersedes DEFSTAN 02-304(PT2)/1(2000) (01/2003)
DocumentType
Standard
PublisherName
UK Ministry of Defence Standards
Status
Superseded
SupersededBy
Supersedes

DEFSTAN 02-304(PT1)/2(2002) : 2002 SHAFTING SYSTEMS AND PROPULSORS - PART 1: DESIGN REQUIREMENTS FOR MAIN PROPULSION SHAFTING
DEFSTAN 02-304(PT1)/3(2015) : 2015 SHAFTING SYSTEMS & PROPULSORS - PART 1: DESIGN REQUIREMENTS FOR MAIN PROPULSION SHAFTING
DEFSTAN 02-136/2(2004) : 2004 DESIGN, TESTING AND ACCEPTANCE REQUIREMENTS FOR WATERTIGHT INTEGRITY OF SUBMARINES CATEGORY 1
DEFSTAN 02-136/3(2010) : 2010 DESIGN POLICY, PRINCIPLES, TESTING AND ACCEPTANCE REQUIREMENTS FOR WATERTIGHT INTEGRITY OF SUBMARINES
DEFSTAN 02-747(PT3)/2(2011) : 2011 REQUIREMENTS FOR NICKEL ALUMINIUM BRONZE CASTINGS AND INGOTS - PART 3: NICKEL ALUMINIUM BRONZE COMMERCIAL ALLOY INGOTS AND SAND CASTINGS

BS 4500-4:1985 ISO limits and fits Specification for system of cone (taper) fits for cones from <i>C</i>=1:3 to 1:500, lengths from 6 mm to 630 mm and diameters up to 500 mm
BS 1916-2:1953 Limits and fits for engineering Guide to the selection of fits in BS 1916:Part 1
DEFSTAN 02-704(PT5)/1(2000) : 2000 REQUIREMENTS FOR CATHODIC PROTECTION - PART 5: GENERAL INFORMATION ON BI-METALLIC COUPLES
DEFSTAN 02-362/1(2000) : 2000 TYPE AND PRODUCTION TESTING OF MECHANICAL EQUIPMENT
BS 4500-5:1988 ISO limits and fits. Specification for system of cone tolerances for conical workpieces from $7IC$7R = 1:3 to 1:500 and lengths from 6 mm to 630 mm
DEFSTAN 02-747(PT4)/1(2000) : 2000 REQUIREMENTS FOR NICKEL ALUMINIUM BRONZE CASTINGS AND INGOTS - PART 4: NICKEL ALUMINIUM BRONZE NAVAL ALLOY WELDING RESTRICTED TO THE NON-WETTED SURFACE (CLASS 1 AND 2 CASTINGS ONLY)
BS EN 1564:2011 Founding. Ausferritic spheroidal graphite cast irons
DEFSTAN 02-849/1(2000) : 2000 STEEL CASTINGS FOR STRUCTURAL, ENGINEERING AND PRESSURE PURPOSES
DEFSTAN 02-745(PT2)/1(2000) : 2000 CLASSIFICATION, INSPECTION REQUIREMENTS AND ACCEPTANCE STANDARDS FOR CASTINGS - PART 2: STEEL CASTINGS
DEFSTAN 02-791(PT2)/1(2000) : 2000 REQUIREMENTS FOR WELDABLE STRUCTURAL STEELS - PART 2: NOTCH TOUGH MILD STEEL-PLATE
DEFSTAN 02-723/1(2000) : 2000 REQUIREMENTS FOR MARKER PLATES
BS EN 20286-1:1993 ISO system of limits and fits ISO system of limits and fits. Bases of tolerances, deviations and fits
BS EN 1563:2011 Founding. Spheroidal graphite cast irons
DEFSTAN 02-747(PT3)/1(2000) : 2000 REQUIREMENTS FOR NICKEL ALUMINIUM BRONZE CASTINGS AND INGOTS - PART 3: NICKEL ALUMINIUM BRONZE COMMERCIAL ALLOY INGOTS AND SAND CASTINGS
DEFSTAN 02-704(PT2)/1(2000) : 2000 REQUIREMENTS FOR CATHODIC PROTECTION - PART 2: IMPRESSED CURRENT CATHODIC PROTECTION SYSTEM CATEGORY 2
BS 4500-1:1969 ISO limits and fits General, tolerances and deviations
DEFSTAN 02-863/1(2000) : 2000 REQUIREMENTS FOR THE CLASSIFICATION, DIMENSIONS, TOLERANCES AND GENERAL STANDARDS OF ACCEPTANCE FOR COPPER AND NICKEL ALLOY CASTINGS
DEFSTAN 02-704(PT3)/1(2000) : 2000 REQUIREMENTS FOR CATHODIC PROTECTION - PART 3: SACRIFICIAL ANODE OR SELF-ENERGIZED SYSTEM
DEFSTAN 02-747(PT1)/1(2000) : 2000 REQUIREMENTS FOR NICKEL ALUMINIUM BRONZE CASTINGS AND INGOTS - PART 1: NICKEL ALUMINIUM BRONZE NAVAL ALLOY CENTRIFUGALLY CAST
DEFSTAN 02-352/1(2000) : 2000 SECOND MACHINERY INSPECTION AND CONTRACTORS SEA TRIALS OF PROPULSION MACHINERY IN HM SURFACE SHIPS
DEFSTAN 02-722/1(2000) : 2000 REQUIREMENTS FOR THE PREPARATION, IDENTIFICATION AND MANAGEMENTS OF DRAWINGS
DEFSTAN 02-747(PT5)/1(2000) : 2000 REQUIREMENTS FOR NICKEL ALUMINIUM BRONZE CASTINGS AND INGOTS - PART 5: DESIGN AND MANUFACTURE OF NICKEL-ALUMINIUM-BRONZE SAND CASTINGS
BS 1134-2:1990 Assessment of surface texture. Guidance and general information
DEFSTAN 02-791(PT1)/1(2000) : 2000 REQUIREMENTS FOR WELDABLE STRUCTURAL STEELS - PART 1: MILD STEEL - PLATE, SECTIONS AND BARS
DEFSTAN 02-839/1(2000) : 2000 REQUIREMENTS FOR WHITE METAL INGOTS
DEFSTAN 02-704(PT4)/1(2000) : 2000 REQUIREMENTS FOR CATHODIC PROTECTION - PART 4: SHIPS FITTING OUT, SHIPS IN REFIT OR LAID-UP
BS EN 20286-2:1993 ISO system of limits and fits ISO system of limits and fits. Tables of standard tolerance grades and limit deviations for holes and shafts
DEFSTAN 02-791(PT3)/1(2000) : 2000 REQUIREMENTS FOR WELDABLE STRUCTURAL STEELS - PART 3: B QUALITY STEEL-PLATES AND SECTIONS
DEFSTAN 02-791(PT4)/1(2000) : 2000 REQUIREMENTS FOR WELDABLE STRUCTURAL STEELS - PART 4: 'BX' QUALITY STEEL-PLATES
DEFSTAN 02-823/1(2000) : 2000 REQUIREMENTS FOR THE WELDING OF CAST NICKEL ALLOY 625 CATEGORY 2
DEFSTAN 02-304(PT1)/2(2002) : 2002 SHAFTING SYSTEMS AND PROPULSORS - PART 1: DESIGN REQUIREMENTS FOR MAIN PROPULSION SHAFTING
DEFSTAN 02-747(PT2)/1(2000) : 2000 REQUIREMENTS FOR NICKEL ALUMINIUM BRONZE CASTINGS AND INGOTS - PART 2: NICKEL ALUMINIUM BRONZE NAVAL ALLOY INGOTS AND SAND CASTINGS WITH WELDING PERMITTED TO THE WETTED SURFACE
BS 1916-3:1963 Limits and fits for engineering Recommendations for tolerances, limits and fits for large diameters
DEFSTAN 02-704(PT1)/1(2000) : 2000 REQUIREMENTS FOR CATHODIC PROTECTION - PART 1: SYSTEMS GENERAL

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.