|
DIN 15400:1990-06
|
LIFTING HOOKS - MATERIALS, MECHANICAL PROPERTIES, LIFTING CAPACITY AND STRESSES |
|
DIN 7354:1978-08
|
WOOD AND LEATHER MARKING PUNCHES |
|
DIN 50150:2000-10
|
TESTING OF METALLIC MATERIALS - CONVERSION OF HARDNESS VALUES |
|
DIN 59361:1981-10
|
GRINDED AND POLISHED BRIGHT ROUND STEEL; DIMENSIONS, TOLERANCES ACCORDING TO ISO TOLERANCES ZONE H6 |
|
DIN 65038-1:1989-08
|
AEROSPACE; STEEL, NICKEL- AND COBALT-ALLOYS BARS; TECHNICAL SPECIFICATION |
|
DIN 1016:1987-06
|
STEEL FLAT PRODUCTS - HOT ROLLED SHEET AND STRIP - LIMIT DEVIATIONS, FORM AND MASS TOLERANCES |
|
DIN 48065-1:1980-10
|
BALL EYES WITHOUT PROTECTIVE FITTING ATTACHMENT, FOR U-SHAPED STRAPS, FOR OVERHEAD POWER LINES |
|
DIN 740-1:1986-08
|
POWER TRANSMISSION ENGINEERING; FLEXIBLE SHAFT COUPLINGS; TECHNICAL DELIVERY CONDITIONS |
|
DIN 3761-7:1984-01
|
ROTARY SHAFT LIP TYPE SEALS FOR AUTOMOBILES; TEST; SKITTLE MEASURING MANDREL |
|
DIN 6916:1989-10
|
ROUND WASHERS FOR HIGH-TENSILE STRUCTURAL BOLTING |
|
DIN 43763:1986-03
|
MEASUREMENT AND CONTROL - ELECTRICAL TEMPERATURE SENSORS - METAL PROTECTING TUBES FOR THERMOMETERS WITH INSERTED SENSOR UNITS |
|
ISO 18265:2013
|
Metallic materials Conversion of hardness values |
|
DIN 17240:1976-07
|
HEAT RESISTING AND HIGHLY HEAT RESISTING MATERIALS FOR BOLTS AND NUTS - QUALITY SPECIFICATIONS |
|
I.S. EN ISO 18265:2013
|
METALLIC MATERIALS - CONVERSION OF HARDNESS VALUES (ISO 18265:2013) |
|
VDE 0210 : 1985
|
PLANNING AND DESIGN OF OVERHEAD POWER LINES WITH RATED VOLTAGES ABOVE 1 KV |
|
11/30210148 DC : 0
|
BS EN ISO 18265 - METALLIC MATERIALS - CONVERSION OF HARDNESS VALUES |
|
DIN 1651:1988-04
|
FREE-CUTTING STEELS - TECHNICAL DELIVERY CONDITIONS |
|
DIN EN 12812:2008-12
|
FALSEWORK - PERFORMANCE REQUIREMENTS AND GENERAL DESIGN |
|
UNI EN ISO 18265 : 2014
|
METALLIC MATERIALS - CONVERSION OF HARDNESS VALUES |
|
DIN 50191:1987-09
|
HARDENABILITY TEST BY END QUENCHING |
|
VDE 0220-1 : 1971
|
SPECIFICATION FOR DETACHABLE CABLE CLAMPS TO BE USED IN POWER CABLE INSTALLATIONS UP TO 1000 V |
|
DIN 65299:1988-12
|
AEROSPACE; UNIVERSAL JOINTS, NEEDLE BEARING SUPPORTED, LONG-TIME LUBRICATED, FOR ROTARY SHAFTS; DOUBLE JOINTS; CONNECTION DIMENSIONS, LOADS MASSES |
|
DIN 4420-2:1990-12
|
SERVICE AND WORKING SCAFFOLDS - LADDER SCAFFOLDS - SAFETY REQUIREMENTS |
|
DIN 4112 : 1983 AMD 1 2006
|
TEMPORARY STRUCTURES; CODE OF PRACTICE FOR DESIGN AND CONSTRUCTION |
|
DIN VDE 0210 : 1985
|
PLANNING AND DESIGN OF OVERHEAD POWER LINES WITH RATED VOLTAGES ABOVE 1 KV |
|
DIN 17140-1:1983-03
|
WIRE ROD FOR COLD DRAWING - TECHNICAL DELIVERY CONDITIONS FOR BASIC STEEL AND UNALLOYED QUALITY STEELS |
|
DIN 1654-4:1989-10
|
COLD HEADING AND COLD EXTRUDING STEELS - TECHNICAL DELIVERY CONDITIONS FOR STEELS FOR QUENCHING AND TEMPERING |
|
DIN 15155:1986-12
|
PALLETS - BOX PALLET WITH MESH SIDE PANELS AND 2 FRONTSIDE FLAPS |
|
DIN 3990-5:1987-12
|
CALCULATION OF LOAD CAPACITY OF CYLINDRICAL GEARS; ENDURANCE LIMITS AND MATERIAL QUALITIES |
|
DIN 17014-1:1988-08
|
HEAT TREATMENT OF FERROUS MATERIALS - TERMINOLOGY |
|
DIN EN ISO 18265:2014-02
|
METALLIC MATERIALS - CONVERSION OF HARDNESS VALUES (ISO 18265:2013) |
|
UNE-EN ISO 18265:2014
|
Metallic materials - Conversion of hardness values (ISO 18265:2013) |
|
EN ISO 18265:2013
|
Metallic materials - Conversion of hardness values (ISO 18265:2013) |
|
DIN 8166:1992-03
|
ROLLERS FOR CONVEYOR CHAINS WITH SOLID PINS, TYPE FV AND FVT; |
|
DIN 3341:1989-07
|
PLATE VALVES FOR DISPLACEMENT COMPRESSORS; SUCTION VALVES, DISCHARGE VALVES; MAIN DIMENSIONS, MATERIALS, INSTALLATION |
|
DIN 59360:1981-10
|
GROUND AND POLISHED BRIGHT ROUND STEEL; DIMENSIONS; PERMISSIBLE DEVIATIONS ACCORDING TO ISO TOLERANCE ZONE H7 |
|
DIN 6918:1990-04
|
SQUARE TAPER WASHERS FOR U-SECTIONS FOR HIGH-TENSILE STRUCTURAL BOLTING |
|
DIN 6917:1989-10
|
SQUARE TAPER WASHERS FOR I-SECTIONS FOR HIGH-TENSILE STRUCTURAL BOLTING |
|
DIN 54452:1981-11
|
TESTING OF ADHESIVES FOR METALS AND ADHESIVELY BONDED METAL JOINTS; COMPRESSION SHEAR TEST |
|
DIN 65298:1988-12
|
AEROSPACE; UNIVERSAL JOINTS, NEEDLE BEARING SUPPORTED, LONG-TIME LUBRICATED, FOR ROTARY SHAFTS; SINGLE JOINTS; CONNECTION DIMENSIONS, LOADS, MASSES |
|
DIN 15063:1977-12
|
LIFTING APPLIANCES; SHEAVES, TECHNICAL CONDITIONS |
|
BS EN ISO 18265:2013 (published 2013-10)
|
Metallic materials. Conversion of hardness values |