• There are no items in your cart

DIN EN 12864:2006-03

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

LOW-PRESSURE, NON ADJUSTABLE REGULATORS HAVING A MAXIMUM OUTLET PRESSURE OF LESS THAN OR EQUAL TO 200 MBAR, WITH A CAPACITY OF LESS THAN OR EQUAL TO 4 KG/H, AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES
Available format(s)

Hardcopy , PDF

Superseded date

08-01-2013

Language(s)

English

Published date

01-01-2006

1 Scope
2 Normative references
3 Terms and definitions
   3.1 General definitions
   3.2 Definitions concerning gas
   3.3 Definitions concerning pressures
   3.4 Definitions concerning rates
4 Terminology
5 Structural characteristics
   5.1 General
   5.2 Materials
   5.3 Special requirements
   5.4 Mechanical strength
   5.5 Soundness
   5.6 Mechanical endurance
   5.7 Resistance to humidity changes
   5.8 Resistance to corrosion
6 Performance characteristics
7 Test methods
   7.1 General conditions
   7.2 Verification of structural characteristics
   7.3 Verification of performance characteristics
8 Marking - Packaging - Instructions
   8.1 General
   8.2 Marking of the regulator
   8.3 Packaging
   8.4 Instructions for use and maintenance
Annex A (normative) Special requirements for regulators
        fitted with pressure or rate operated safety
        devices
   A.1 Regulators fitted with an overpressure relief
        valve of a limited flow rate
   A.2 Regulators fitted with an overpressure shut off
        device
   A.3 Regulators fitted with an underpressure shut off
        safety device
   A.4 Regulators fitted with an excess flow valve
Annex B (normative) Special requirements for regulators
        fitted with a temperature operated safety device
   B.1 Definition
   B.2 Structural characteristics
   B.3 Performance characteristics
   B.4 Test methods
Annex C (normative) Special requirements for low pressure
        regulators under extreme temperature conditions
Annex D (normative) Multimode connection regulator for
        LPG cylinders to supply appliances installed in
        caravans and motor caravans
   D.1 Scope
   D.2 Design characteristics
   D.3 Structural characteristics
   D.4 Operating characteristics
   D.5 Marking - Packaging - Instructions
Annex E (normative) Complementary test requirements for
        non metallic thermoplastic or thermosetting
        materials used in the construction of regulators
   E.1 Scope
   E.2 Materials
   E.3 Special conditions for carrying out the test
        mentioned in the body of the standard
   E.4 Special requirements
Annex F (normative) Supplementary requirements for
        reinforced diaphragms and elastomeric seals
        used in LPG appliances and their associated
        equipment
Annex G (normative) Inlet connections
Annex H (normative) Outlet connections
Annex I (normative) Special requirements for low pressure
        non adjustable regulators fitted with two or
        three outlets for outdoor use
   I.1 Structural characteristics
   I.2 Performance characteristics
   I.3 Test methods
   I.4 Marking
Annex J (normative) Method for measuring leaks at test
        pressures less than or equal to 20 bar
   J.1 Scope
   J.2 Diagram of the test bench
   J.3 Determination of coefficient K
   J.5 Checks
Annex K (normative) Special requirements for regulators
        fitted with an inlet valve
   K.1 Definition
   K.2 Structural characteristics
   K.3 Performance characteristics: mechanical strength
   K.4 Test method
Annex L (informative) Alternative test method for
        resistance to corrosion
   L.1 Principle
   L.2 Reagents
   L.3 Apparatus
   L.4 Test method
   L.5 Results
Annex ZA (informative) Clauses of this European Standard
         addressing essential requirements or other
         provisions of EU directives

Specifies the structural and operational characteristics, the safety requirements and test methods, the marking, of low-pressure, non adjustable regulators for butane, propane or their mixtures, referred to in the body of the text as "regulators".

DevelopmentNote
Supersedes DIN 4811-1, DIN 4811-4 and DIN 4811-7. (12/2001) Supersedes DIN 4811-2. (06/2008)
DocumentType
Standard
Pages
124
PublisherName
German Institute for Standardisation (Deutsches Institut für Normung)
Status
Superseded
SupersededBy
Supersedes

BGR 146 : 2003 FLUESSIGGASANLAGEN ZU HAUSHALTSZWECKEN AUF WASSERFAHRZEUGEN IN DER BINNENSCHIFFAHRT

DIN 50021:1988-06 SPRAY TESTS WITH DIFFERENT SODIUM CHLORIDE SOLUTIONS
ISO 426-1:1983 Wrought copper-zinc alloys — Chemical composition and forms of wrought products — Part 1: Non-leaded and special copper-zinc alloys
ISO 8434-1:2007 Metallic tube connections for fluid power and general use Part 1: 24 degree cone connectors
DIN EN 2155-13:1993-04 AEROSPACE SERIES - TEST METHODS FOR TRANSPARENT MATERIALS FOR AIRCRAFT GLAZING - PART 13: DETERMINATION OF TEMPERATURE AT DEFLECTION UNDER LOAD
DIN 17660:1983-12 WROUGHT COPPER ALLOYS - COPPER-ZINC ALLOYS - (BRASS) - (SPECIAL BRASS) - COMPOSITION
ISO 75:1987 Plastics and ebonite Determination of temperature of deflection under load
ISO 426-2:1983 Wrought copper-zinc alloys — Chemical composition and forms of wrought products — Part 2: Leaded copper-zinc alloys
ISO 565:1990 Test sieves — Metal wire cloth, perforated metal plate and electroformed sheet — Nominal sizes of openings
EN 561:2002 Gas welding equipment - Quick-action coupling with shut-off valves for welding, cutting and allied processes
EN 560:2005/AC:2007 GAS WELDING EQUIPMENT - HOSE CONNECTIONS FOR EQUIPMENT FOR WELDING, CUTTING AND ALLIED PROCESSES
EN ISO 7253 : 2001 PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO NEUTRAL SALT SPRAY (FOG)
DIN EN 1179:2003-09 ZINC AND ZINC ALLOYS - PRIMARY ZINC
EN ISO 3166-1:2014 Codes for the representation of names of countries and their subdivisions - Part 1: Country codes (ISO 3166-1:2013)
DIN ISO 565:1998-12 TEST SIEVES - METAL WIRE CLOTH, PERFORATED METAL PLATE AND ELECTROFORMED SHEET - NOMINAL SIZES OF OPENINGS
VDE 0471-11-10 : 2014 COR 1 2015 FIRE HAZARD TESTING - PART 11-10: TEST FLAMES - 50 W HORIZONTAL AND VERTICAL FLAME TEST METHODS (IEC 60695-11-10:2013)
DIN 2999-1:1983-07 PIPE THREADS FOR TUBES AND FITTINGS - PARALLEL INTERNAL THREAD AND TAPER EXTERNAL THREAD - TREAD DIMENSIONS
ISO 4628-3:2016 Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 3: Assessment of degree of rusting
DIN EN ISO 180:2013-08 PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH (ISO 180:2000 + AMD.1:2006 + AMD.2:2013)
DIN EN 12844:1999-01 ZINC AND ZINC ALLOYS - CASTINGS - SPECIFICATIONS
ISO 7253:1996 Paints and varnishes — Determination of resistance to neutral salt spray (fog)
EN ISO 4628-3:2016 Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 3: Assessment of degree of rusting (ISO 4628-3:2016)
ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation
EN 437:2003+A1:2009 Test gases - Test pressures - Appliance categories
ISO 180:2000 Plastics Determination of Izod impact strength
ISO 1210:1992 Plastics — Determination of the burning behaviour of horizontal and vertical specimens in contact with a small-flame ignition source
ISO 4892-3:2016 Plastics Methods of exposure to laboratory light sources Part 3: Fluorescent UV lamps
DIN EN ISO 527-3:2003-07 PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 3: TEST CONDITIONS FOR FILMS AND SHEETS
EN ISO 8434-1:2007/AC:2009 METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - PART 1: 24 DEGREE CONE CONNECTORS
ISO 9227:2017 Corrosion tests in artificial atmospheres — Salt spray tests
ISO 3166-1:2013 Codes for the representation of names of countries and their subdivisions Part 1: Country codes
EN 549:1994 Rubber materials for seals and diaphragms for gas appliances and gas equipment
ISO 301:2006 Zinc alloy ingots intended for castings
DIN EN ISO 4892-3:2016-10 PLASTICS - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 3: FLUORESCENT UV LAMPS (ISO 4892-3:2016)
ISO 178:2010 Plastics Determination of flexural properties
ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation

View more information
US$202.35
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.