DIN EN 12864 E : 2006 AMD 3 2010
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
LOW PRESSURE, NON ADJUSTABLE REGULATORS HAVING A MAXIMUM OUTLET PRESSURE OF LESS THAN OR EQUAL TO 200 MBAR, WITH A CAPACITY OF LESS THAN OR EQUAL TO 4 KG/H, AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES
08-01-2013
01-12-2013
Foreword to EN 12864:2001
Foreword to EN 12864:2001/A1:2003
Foreword to EN 12864:2001/A2:2005
1 Scope
2 Normative references
3 Terms and definitions
3.1 General definitions
3.2 Definitions concerning gas
3.3 Definitions concerning pressures
3.4 Definitions concerning rates
4 Terminology
5 Structural characteristics
5.1 General
5.2 Materials
5.3 Special requirements
5.4 Mechanical strength
5.5 Soundness
5.6 Mechanical endurance
5.7 Resistance to humidity changes
5.8 Resistance to corrosion
6 Performance characteristics
7 Test methods
7.1 General conditions
7.2 Verification of structural characteristics
7.3 Verification of performance characteristics
8 Marking - Packaging - Instructions
8.1 General
8.2 Marking of the regulator
8.3 Packaging
8.4 Instructions for use and maintenance
Annex A (normative) Special requirements for regulators fitted
with pressure or rate operated safety devices
A.1 Regulators fitted with an overpressure relief valve
of a limited flow rate
A.2 Regulators fitted with an overpressure shut off device
A.3 Regulators fitted with an underpressure shut off
safety device
A.4 Regulators fitted with an excess flow valve
Annex B (normative) Special requirements for regulators fitted
with a temperature operated safety device
B.1 Definition
B.2 Structural characteristics
B.3 Performance characteristics
B.4 Test methods
Annex C (normative) Special requirements for low pressure
regulators under extreme temperature conditions
Annex D (normative) Multimode connection regulator for LPG
cylinders to supply appliances installed in caravans
and motor caravans or freshwater boats
D.1 Scope
D.2 Design characteristics
D.3 Structural characteristics
D.4 Operating characteristics
D.5 Marking - Packaging - Instructions
Annex E (normative) Complementary test requirements for non
metallic thermoplastic or thermosetting materials used
in the construction of regulators
E.1 Scope
E.2 Materials
E.3 Special conditions for carrying out the tests mentioned
in the body of the standard
E.4 Special requirements
E.5 Sampling and order of tests
Annex F (normative) Supplementary requirements for reinforced
diaphragms and elastomeric seals used in LPG appliances
and their associated equipment
Annex G (normative) Inlet connections
Annex H (normative) Outlet connections
Annex I (normative) Special requirements for low pressure non
adjustable regulators fitted with two or three outlets
for outdoor use
I.1 Structural characteristics
I.2 Performance characteristics
I.3 Test methods
I.4 Marking
Annex J (normative) Method for measuring leaks at test pressures
less than or equal to 20 bar
J.1 Scope
J.2 Diagram of the test bench
J.3 Determination of coefficient K
J.4 Measurement of the leak
J.5 Checks
Annex K (normative) Special requirements for regulators fitted
with an inlet valve
K.1 Definition
K.2 Structural characteristics
K.3 Performance characteristics: mechanical strength
K.4 Test method
Annex L (informative) Alternative test method for resistance
to corrosion
L.1 Principle
L.2 Reagents
L.3 Apparatus
L.4 Test method
L.5 Results
Annex M (normative) Regulator for LPG cylinders to supply
appliances installed in seawater boats
M.1 Scope
M.2 General
M.3 Maximum guaranteed rate
M.4 Regulators fitted with a pressure relief valve
M.5 Vent
M.6 Connections
M.7 Material
M.8 Corrosion
M.9 Marking
M.10 Instructions for use and maintenance
Annex ZA (informative) Clauses of this European Standard
addressing essential requirements or other provisions
of EU directives
National Annex NA (informative) Bibliography
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.