• There are no items in your cart

DIN EN 13483:2013-09

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems - Specification
Available format(s)

Hardcopy , PDF

Superseded date

11-26-2022

Language(s)

German, English

Published date

09-01-2013

National foreword
National Annex NA (informative) - Bibliography
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Materials and construction
6 Pressure requirements
7 Dimensions and tolerances
8 Physical properties
9 End fittings
10 Type tests
11 Frequency of testing
12 Marking
Annex A (normative) - Test method for determination of low
        temperature class resistance at -30 degrees C (for
        normal temperature class) and -40 degrees C (for low
        temperature class)
Annex B (normative) - Test method for pressure requirements
        of vapour recovery hoses and tubes
Annex C (normative) - Test method for determination of
        change in length due to swelling
Annex D (normative) - Test method for determination of
        pressure loss
Annex E (normative) - Method for determination of adhesion
        between components
Annex F (normative) - Test method for the determination of
        low temperature flexibility
Annex G (normative) - Test method for the determination
        of rate of fuel permeation
Annex H (normative) - Test method for flammability
Annex I (normative) - Test method for the determination
        of leakage (leak test)
Annex J (normative) - Test method for fatigue strength under
        reversed bending stresses (flex test)
Annex K (normative) - End-fitting pull-off test
Annex L (normative) - Test frequency for type tests and routine
        tests
Annex M (informative) - Test frequency for production
        acceptance tests
Bibliography

This standard is included in DIN Handbook 380.

DevelopmentNote
Supersedes DIN 2824 (07/2002)
DocumentType
Standard
Pages
34
PublisherName
German Institute for Standardisation (Deutsches Institut für Normung)
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
NF EN 13483 : 2013 Identical
NBN EN 13483 : 2013 Identical
NEN EN 13483 : 2013 Identical
NS EN 13483 : 2013 Identical
I.S. EN 13483:2013 Identical
UNE-EN 13483:2013 Identical
SN EN 13483 : 2013 Identical
UNI EN 13483 : 2013 Identical
BS EN 13483:2013 Identical
EN 13483:2013 Identical
ONORM EN 13483 : 2013 Identical

EN ISO 8330:2014 Rubber and plastics hoses and hose assemblies - Vocabulary (ISO 8330:2014)
DIN 53504:2015-08 (Draft) TESTING OF RUBBER - DETERMINATION OF TENSILE STRENGTH AT BREAK, TENSILE STRESS AT YIELD, ELONGATION AT BREAK AND STRESS VALUES IN A TENSILE TEST
EN ISO 1402:2009 Rubber and plastics hoses and hose assemblies - Hydrostatic testing (ISO 1402:2009)
DIN 53508:2000-03 Accelerated ageing of rubber
EN ISO 4671:2007/A1:2011 Rubber and plastics hoses and hose assemblies - Methods of measurement of the dimensions of hoses and the lengths of hose assemblies - Amendment 1: Clarification of position at which outside diameter is measured (ISO 4671:2007/Amd 1:2011)
EN 228:2012+A1:2017 Automotive fuels - Unleaded petrol - Requirements and test methods
ISO 6801:1983 Rubber or plastics hoses Determination of volumetric expansion
ISO 4649:2017 Rubber, vulcanized or thermoplastic — Determination of abrasion resistance using a rotating cylindrical drum device
EN ISO 1307:2008 Rubber and plastics hoses - Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses (ISO 1307:2006)
ISO 188:2011 Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
EN ISO 8031:2009 Rubber and plastics hoses and hose assemblies - Determination of electrical resistance and conductivity (ISO 8031:2009)
DIN ISO 1817:2016-11 RUBBER, VULCANIZED OR THERMOPLASTIC - DETERMINATION OF THE EFFECT OF LIQUIDS (ISO 1817:2015)
EN ISO 7326:2016 Rubber and plastics hoses - Assessment of ozone resistance under static conditions (ISO 7326:2016)
ISO 7326:2016 Rubber and plastics hoses Assessment of ozone resistance under static conditions
EN ISO 8033:2017 Rubber and plastics hoses - Determination of adhesion between components (ISO 8033:2016)
ISO 8330:2007 Rubber and plastics hoses and hose assemblies Vocabulary
ISO 10619-1:2011 Rubber and plastics hoses and tubing Measurement of flexibility and stiffness Part 1: Bending tests at ambient temperature
EN 26801:1993/A1:2011 RUBBER OR PLASTICS HOSES - DETERMINATION OF VOLUMETRIC EXPANSION (ISO 6801:1983/AMD 1:2011)
ISO 37:2017 Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
ISO 4671:2007 Rubber and plastics hoses and hose assemblies Methods of measurement of the dimensions of hoses and the lengths of hose assemblies
ISO 554:1976 Standard atmospheres for conditioning and/or testing — Specifications
ISO 1402:2009 Rubber and plastics hoses and hose assemblies Hydrostatic testing
ISO 1307:2006 Rubber and plastics hoses — Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses
ISO 8033:2016 Rubber and plastics hoses Determination of adhesion between components
ISO 8031:2009 Rubber and plastics hoses and hose assemblies Determination of electrical resistance and conductivity
ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
ISO 1817:2015 Rubber, vulcanized or thermoplastic Determination of the effect of liquids

View more information
US$108.91
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.