• There are no items in your cart

DIN EN 14042:2003-07

Withdrawn
Withdrawn

A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

WORKPLACE ATMOSPHERES - GUIDE FOR THE APPLICATION AND USE OF PROCEDURES FOR THE ASSESSMENT OF EXPOSURE TO CHEMICAL AND BIOLOGICAL AGENTS
Available format(s)

Hardcopy , PDF

Withdrawn date

03-01-2016

Language(s)

English

Published date

01-01-2003

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Measurement objectives and strategy
    4.1 General
    4.2 EN 689
         4.2.1 General
         4.2.2 Occupational exposure assessment
         4.2.3 Periodic measurements
         4.2.4 Reassessment
         4.2.5 Measurement strategy
    4.3 EN 482
    4.4 Other tasks
5 Selection of the measurement procedure or device
    5.1 General
    5.2 Selection flow chart
    5.3 Selectivity requirements
    5.4 The influence of environmental parameters
    5.5 Fitness for purpose
6 Operating principles and characteristics
    6.1 General
    6.2 Measurement of chemical agents
         6.2.1 Short term detector tubes
         6.2.2 Procedures using an impinger/bubbler as
                sampler
         6.2.3 Procedures using a denuder as sampler
         6.2.4 Procedures using a particle selector to
                sample size fractions
         6.2.5 Procedures to measure chemical agents
                present as mixtures of particles and vapour
         6.2.6 Procedures using pumped samplers for gases
                and vapours
         6.2.7 Procedures using diffusive samplers
         6.2.8 Procedures to measure metals and metalloids
                in airborne particles
         6.2.9 Procedures using bags and canisters for
                sampling
    6.3 Measurement of airborne micro-organisms and
         endotoxin
         6.3.1 Methods using an impactor as sampler
         6.3.2 Procedures using impingers as samplers
         6.3.3 Procedures using filtration samplers
7 Operation of the measuring devices
    7.1 Guidance for use of measuring procedures and
         personal, portable and transportable measuring
         devices
         7.1.1 General
         7.1.2 Transportation
         7.1.3 Storage conditions and shelf life
         7.1.4 Field measurements
         7.1.5 Inspection and field check
    7.2 Guidance for use of fixed measuring devices
         7.2.1 General
         7.2.2 Installation
         7.2.3 Location
         7.2.4 Inspection and field check
8 Recommendations on the use of sampling pumps
    8.1 General
    8.2 Factors influencing the flow rate stability of
         a pump
    8.3 Flow rate calibration
    8.4 Calculation of flow rates and sampling volumes
         8.4.1 Mean Volumetric flow rate
         8.4.2 Sampling volume
9 Maintenance and calibration
10 Disposal of measuring devices
11 Requirements for training
12 Quality assurance
Bibliography

Provides guidance on the selection of procedures, and the installation, use and maintenance of devices for determination of concentrations of chemical or biological agents in workplace atmospheres.

DocumentType
Standard
Pages
41
PublisherName
German Institute for Standardisation (Deutsches Institut für Normung)
Status
Withdrawn

Standards Relationship
UNI EN 14042 : 2005 Identical
NEN EN 14042 : 2003 Identical
NF EN 14042 : 2003 Identical
UNE-EN 14042:2004 Identical
I.S. EN 14042:2003 Identical
BS EN 14042:2003 Identical
EN 14042:2003 Identical
NBN EN 14042 : 2003 Identical
NS EN 14042 : 1ED 2003 Identical
SN EN 14042 : 2003 Identical

ISO 6144:2003 Gas analysis Preparation of calibration gas mixtures Static volumetric method
EN 12919:1999 Workplace atmospheres - Pumps for the sampling of chemical agents with a volume flow rate of over 5 l/min - Requirements and test methods
EN 838:2010 Workplace exposure - Procedures for measuring gases and vapours using diffusive samplers - Requirements and test methods
ENV 13936 : DRAFT 2001 WORKPLACE ATMOSPHERES - MEASUREMENT OF CHEMICAL AGENTS PRESENT AS MIXTURES OF AIRBORNE PARTICLES AND VAPOUR - REQUIREMENTS AND TEST METHODS
ISO 6145-7:2009 Gas analysis Preparation of calibration gas mixtures using dynamic volumetric methods Part 7: Thermal mass-flow controllers
EN 1076:2009 Workplace exposure - Procedures for measuring gases and vapours using pumped samplers - Requirements and test methods
EN 482:2012+A1:2015 Workplace exposure - General requirements for the performance of procedures for the measurement of chemical agents
EN 13890:2009 Workplace exposure - Procedures for measuring metals and metalloids in airborne particles - Requirements and test methods
ISO 6147:1979 Gas analysis Preparation of calibration gas mixtures Saturation method
ISO 6143:2001 Gas analysis — Comparison methods for determining and checking the composition of calibration gas mixtures
EN 13098:2000 Workplace atmosphere - Guidelines for measurement of airborne micro-organisms and endotoxin
ISO 6879:1995 Air quality — Performance characteristics and related concepts for air quality measuring methods
EN 45544-4 : 2016 WORKPLACE ATMOSPHERES - ELECTRICAL APPARATUS USED FOR THE DIRECT DETECTION AND DIRECT CONCENTRATION MEASUREMENT OF TOXIC GASES AND VAPOURS - PART 4 - GUIDE FOR SELECTION, INSTALLATION, USE AND MAINTENANCE
ISO 6142:2001 Gas analysis Preparation of calibration gas mixtures Gravimetric method
ISO 6145-10:2002 Gas analysis — Preparation of calibration gas mixtures using dynamic volumetric methods — Part 10: Permeation method
ISO 6145-2:2014 Gas analysis Preparation of calibration gas mixtures using dynamic methods Part 2: Piston pumps
EN 13205:2001 Workplace atmospheres - Assessment of performance of instruments for measurement of airborne particle concentrations
ISO 6145-5:2009 Gas analysis Preparation of calibration gas mixtures using dynamic volumetric methods Part 5: Capillary calibration devices
ISO 6145-4:2004 Gas analysis Preparation of calibration gas mixtures using dynamic volumetric methods Part 4: Continuous syringe injection method
EN 1231:1996 Workplace atmospheres - Short term detector tube measurement systems - Requirements and test methods
ISO 6145-9:2009 Gas analysis Preparation of calibration gas mixtures using dynamic volumetric methods Part 9: Saturation method
EN 1540:2011 Workplace exposure - Terminology
ISO 6145-1:2003 Gas analysis Preparation of calibration gas mixtures using dynamic volumetric methods Part 1: Methods of calibration
ISO 6141:2015 Gas analysis Contents of certificates for calibration gas mixtures
EN 1232:1997 Workplace atmospheres - Pumps for personal sampling of chemical agents - Requirements and test methods
ISO 6145-6:2017 Gas analysis — Preparation of calibration gas mixtures using dynamic methods — Part 6: Critical flow orifices
ISO 3534-1:2006 Statistics — Vocabulary and symbols — Part 1: General statistical terms and terms used in probability

View more information

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.