DIN EN 14382 E : 2009
Current
Current
The latest, up-to-date edition.
SAFETY DEVICES FOR GAS PRESSURE REGULATING STATIONS AND INSTALLATIONS - GAS SAFETY SHUT-OFF DEVICES FOR INLET PRESSURES UP TO 100 BAR
Available format(s)
Hardcopy , PDF
Language(s)
English
Published date
01-01-2009
Foreword
1 Scope
2 Normative references
3 Terms, definitions and symbols
4 Construction requirements
5 Functional requirements
6 Testing
7 Test and verification methods
8 Documentation
9 Marking
Annex A (informative) Ice formation
Annex B (informative) Compliance evaluation
Annex C (informative) Pressure drop and flow coefficient
Annex D (informative) Alternative test method
for verification of the strength of the trip
mechanism, valve seat and closing member
Annex E (informative) Sizing equation
Annex F (informative) Inspection certificate
Annex G (informative) Order specification
Annex H (informative) Acceptance test
Annex I (informative) Seat leakage (alternative requirement)
Annex J (normative) Materials
Annex K (informative) Suitability of safety shut-off device
for damp operating conditions
Annex L (informative) Glossary
Annex ZA (informative) Relationship between this
European Standard and the Essential
Requirements of EU Directive 97/23/EC
Bibliography
Defines constructional, functional, testing and marking requirements, sizing and documentation of gas safety shut-off devices used in the pressure regulating stations in accordance with EN 12186 or EN 12279: - for inlet pressures up to 100 bar and nominal diameters up to DN 400; - for an operating temperature range from -20 degree C to +60 degree C, which operate with fuel gases of the 1st and 2nd family in accordance with EN 437 in transmission and distribution networks and also in commercial and industrial installations.
| DevelopmentNote |
Supersedes DIN 3381 E. (11/2005)
|
| DocumentType |
Standard
|
| Pages |
94
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| NBN EN 14382 : 2005 + A1 2009 | Identical |
| NEN EN 14382 : 2005 + A1/C1 2009 | Identical |
| I.S. EN 14382:2005 | Identical |
| SN EN 14382 : 2009 CORR 2009 | Identical |
| UNI EN 14382 : 2009 | Identical |
| UNE-EN 14382:2005 | Identical |
| BS EN 14382 : 2005 | Identical |
| EN 14382:2005+A1:2009/AC:2009 | Identical |
| NF EN 14382 : 2005 + A1 2009 | Identical |
| ONORM EN 14382 : AUG 2009 | Identical |
| EN 12732:2013+A1:2014 | Gas infrastructure - Welding steel pipework - Functional requirements |
| EN 10002-1 : 2001 | METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| EN 1759-3:2003/AC:2004 | FLANGES AND THEIR JOINTS - CIRCULAR FLANGES FOR PIPES, VALVES, FITTINGS AND ACCESSORIES, CLASS DESIGNATED - PART 3: COPPER ALLOY FLANGES |
| ISO 9606-4:1999 | Approval testing of welders — Fusion welding — Part 4: Nickel and nickel alloys |
| ISO/IEC 17050-1:2004 | Conformity assessment Supplier's declaration of conformity Part 1: General requirements |
| ISO 9606-2:2004 | Qualification test of welders — Fusion welding — Part 2: Aluminium and aluminium alloys |
| EN 10226-2:2005 | Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads - Dimensions, tolerances and designation |
| EN 60534-1:2005 | Industrial-process control valves - Part 1: Control valve terminology and general considerations |
| EN ISO 15613:2004 | Specification and qualification of welding procedures for metallic materials - Qualification based on pre-production welding test (ISO 15613:2004) |
| ISO 15614-2:2005 | Specification and qualification of welding procedures for metallic materials Welding procedure test Part 2: Arc welding of aluminium and its alloys |
| EN 13906-1:2013 | Cylindrical helical springs made from round wire and bar - Calculation and design - Part 1 : Compression springs |
| EN 1349:2009 | Industrial process control valves |
| EN ISO 15612:2004 | Specification and qualification of welding procedures for metallic materials - Qualification by adoption of a standard welding procedure (ISO 15612:2004) |
| ISO 15610:2003 | Specification and qualification of welding procedures for metallic materials — Qualification based on tested welding consumables |
| EN 1759-1:2004 | Flanges and their joint - Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 1: Steel flanges, NPS 1/2 to 24 |
| IEC 60534-3-1:2000 | Industrial-process control valves - Part 3-1: Dimensions - Face-to-face dimensions for flanged, two-way, globe-type, straight pattern and centre-to-face dimensions for flanged, two-way, globe-type, angle pattern control valves |
| EN 1759-4:2003 | Flanges and their joint - Circular flanges for pipes, valves, fittings and accessories, class designated - Part 4: Aluminium alloy flanges |
| ISO 188:2011 | Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests |
| EN 1092-3:2003/AC:2007 | FLANGES AND THEIR JOINTS - CIRCULAR FLANGES FOR PIPES, VALVES, FITTINGS AND ACCESSORIES, PN DESIGNATED - PART 3: COPPER ALLOY FLANGES |
| EN ISO 2409:2013 | Paints and varnishes - Cross-cut test (ISO 2409:2013) |
| EN 12516-1:2014 | Industrial valves - Shell design strength - Part 1: Tabulation method for steel valve shells |
| EN ISO 9606-4:1999 | Approval testing of welders - Fusion welding - Part 4: Nickel and nickel alloys (ISO 9606-4:1999) |
| EN 12516-4:2014 | Industrial valves - Shell design strength - Part 4: Calculation method for valve shells manufactured in metallic materials other than steel |
| ISO 6708:1995 | Pipework components Definition and selection of DN (nominal size) |
| EN 45011 : 1998 | GENERAL REQUIREMENTS FOR BODIES OPERATING PRODUCT CERTIFICATION SYSTEMS |
| EN 473:2008 | Non-destructive testing - Qualification and certification of NDT personnel - General principles |
| EN 10045-1 : 1990 | METALLIC MATERIALS - CHARPY IMPACT TEST - PART 1: TEST METHOD |
| ISO 15612:2004 | Specification and qualification of welding procedures for metallic materials Qualification by adoption of a standard welding procedure |
| EN ISO 6708:1995 | Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995) |
| EN ISO 15611:2003 | Specification and qualification of welding procedures for metallic materials - Qualification based on previous welding experience (ISO 15611:2003) |
| ISO 15614-1:2017 | Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys |
| EN 13906-2:2013 | Cylindrical helical springs made from round wire and bar - Calculation and design - Part 2: Extension springs |
| EN 13445-4 : 2014 COR 2017 | UNFIRED PRESSURE VESSELS - PART 4: FABRICATION |
| ISO 1431-1:2012 | Rubber, vulcanized or thermoplastic Resistance to ozone cracking Part 1: Static and dynamic strain testing |
| EN 12279:2000/A1:2005 | GAS SUPPLY SYSTEMS - GAS PRESSURE REGULATING INSTALLATIONS ON SERVICE LINES - FUNCTIONAL REQUIREMENTS |
| ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 1: Arc welding |
| EN 1092-4:2002 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 4: Aluminium alloy flanges |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| ISO 15611:2003 | Specification and qualification of welding procedures for metallic materials — Qualification based on previous welding experience |
| EN 437:2003+A1:2009 | Test gases - Test pressures - Appliance categories |
| ISO 5752:1982 | Metal valves for use in flanged pipe systems Face-to-face and centre-to-face dimensions |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| ISO 148:1983 | Steel — Charpy impact test (V-notch) |
| EN ISO 15614-2:2005 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 2: Arc welding of aluminium and its alloys (ISO 15614-2:2005) |
| EN ISO 9606-2:2004 | Qualification test of welders - Fusion welding - Part 2: Aluminium and aluminium alloys (ISO 9606-2:2004) |
| ISO 175:2010 | Plastics Methods of test for the determination of the effects of immersion in liquid chemicals |
| IEC 60534-3-2:2001 | Industrial-process control valves - Part 3-2: Dimensions - Face-to-face dimensions for rotary control valves except butterfly valves |
| EN 334:2005+A1:2009 | Gas pressure regulators for inlet pressures up to 100 bar |
| EN 60534-3-2:2001 | Industrial-process control valves - Part 3-2: Dimensions - Face-to-face dimensions for rotary control valves except butterfly valves |
| ISO 1518:1992 | Paints and varnishes Scratch test |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 1: Arc welding (ISO 15609-1:2004) |
| EN 60534-3-1:2000/corrigendum:2000 | INDUSTRIAL-PROCESS CONTROL VALVES - PART 3-1: DIMENSIONS - FACE-TO-FACE DIMENSIONS FOR FLANGED, TWO-WAY, GLOBE-TYPE, STRAIGHT PATTERN AND CENTRE-TO-FACE DIMENSIONS FOR FLANGED, TWO-WAY, GLOBE-TYPE, ANGLE PATTERN CONTROL VALVES |
| MSS SP 55 : 2011 | QUALITY STANDARD FOR STEEL CASTINGS FOR VALVES, FLANGES, FITTINGS, AND OTHER PIPING COMPONENTS - VISUAL METHOD FOR EVALUATION OF SURFACE IRREGULARITIES |
| ISO/IEC Guide 2:2004 | Standardization and related activities General vocabulary |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| ISO/IEC Guide 65:1996 | General requirements for bodies operating product certification systems |
| EN ISO/IEC 17050-1:2010 | Conformity assessment - Supplier's declaration of conformity - Part 1: General requirements (ISO/IEC 17050-1:2004, corrected version 2007-06-15) |
| EN ISO 1518:2000 | Paints and varnishes - Scratch test (ISO 1518:1992) |
| ISO 15613:2004 | Specification and qualification of welding procedures for metallic materials Qualification based on pre-production welding test |
| EN 45020 : 2006 | STANDARDIZATION AND RELATED ACTIVITIES - GENERAL VOCABULARY |
| EN 12516-2:2014 | Industrial valves - Shell design strength - Part 2: Calculation method for steel valve shells |
| ISO 2409:2013 | Paints and varnishes Cross-cut test |
| ISO 48:2010 | Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD) |
| EN ISO 15610:2003 | Specification and qualification of welding procedures for metallic materials - Qualification based on tested welding consumables (ISO 15610:2003) |
| ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials General rules |
| EN 1418:1997 | Welding personnel - Approval testing of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials |
| EN 1092-2:1997 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges |
| EN 970:1997 | Non-destructive examination of fusion welds - Visual examination |
| EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
| IEC 60534-1:2005 | Industrial-process control valves - Part 1: Control valve terminology and general considerations |
| EN ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials - General rules (ISO 15607:2003) |
| EN ISO 9606-3 : 1999 | Approval testing of welders - Fusion welding - Part 3: Copper and copper alloys (ISO 9606-3:1999) |
| IEC 60534-3:1976 | Industrial-process control valves. Part 3: Dimensions - Section One: Face-to-face dimensions for flanged, two-way, globe-type control valves |
| EN ISO 175:2010 | Plastics - Methods of test for the determination of the effects of immersion in liquid chemicals (ISO 175:2010) |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
| ISO 9606-3:1999 | Approval testing of welders — Fusion welding — Part 3: Copper and copper alloys |
| EN 287-1:2011 | Qualification test of welders - Fusion welding - Part 1: Steels |
| EN 12186:2014 | Gas infrastructure - Gas pressure regulating stations for transmission and distribution - Functional requirements |
US$216.68
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.