SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR MACHINERY AND EQUIPMENT FOR CONTINUOUS CASTING OF STEEL

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-01-2008

Publisher

German Institute for Standardisation (Deutsches Institut für Normung)

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or measures
  5.1 General
      5.1.1 Introduction
      5.1.2 CCM-arrangement, site inspection
      5.1.3 Safety layout
      5.1.4 Safety devices
      5.1.5 Hydraulic, pneumatic, gas, cooling and lubrication
            systems
      5.1.6 Fluid systems carrying or containing fluids
      5.1.7 Fluids to be discharged to drains
      5.1.8 Personal protective equipment
      5.1.9 Warning devices and safety signs
      5.1.10 Access
      5.1.11 Escape ways
      5.1.12 Electrical equipment
      5.1.13 Safety control system
      5.1.14 Surface temperatures and heat radiation
      5.1.15 Ergonomic principles
      5.1.16 Fire protection
      5.1.17 Operating positions of the CCM
      5.1.18 Movable control box
      5.1.19 Loss of energy
      5.1.20 Harmful areas
      5.1.21 Cooling water systems
      5.1.22 Radioactive sources
      5.1.23 Ladle/tundish emergency systems
      5.1.24 Shroud manipulators
      5.1.25 Cooling chamber
  5.2 List of significant hazards, hazardous situations, safety
      requirements and/or measures
      5.2.1 General
      5.2.2 General
      5.2.3 Casting platform
      5.2.4 Casting machine equipment
      5.2.5 Cutting systems
      5.2.6 Run-out (discharge) area
  5.3 Special safety requirements or measures
      5.3.1 General
      5.3.2 Hold-to-run control device
      5.3.3 Mechanical restraint devices
      5.3.4 Accessible rotating/moving parts
  5.4 Noise reduction as a safety requirement
      5.4.1 Noise sources
      5.4.2 Noise reduction at source by design
      5.4.3 Noise reduction by protective measures
      5.4.4 Noise reduction by information
6 Verification of the safety requirements and/or measures
7 Information for use
  7.1 Signs and warning devices
  7.2 Accompanying documents
      7.2.1 Instruction handbook
      7.2.2 Machine/equipment declaration
      7.2.3 Instruction for transport, setting up/installation
      7.2.4 Information about commissioning and dismantling
      7.2.5 Operation instructions concerning the equipment
      7.2.6 Maintenance manual
  7.3 Minimum marking
  7.4 Training of personnel
Annex A (normative) Safety requirements and/or measures for
        electrical equipment and controls
      A.1 General
      A.2 Special requirements for controls
      A.3 Special requirements for shut-down equipment
          A.3.1 Stop and emergency-off functions
          A.3.2 Emergency stops
          A.3.3 Emergency stop functions
          A.3.4 Emergency stop assigned to areas
Annex B (normative) Equipment of a CCM covered by this standard
      B.1 Casting platform
      B.2 Casting machine equipment
      B.3 Cutting area
      B.4 Run-out (discharge) area
      B.5 General equipment
Annex C (normative) Noise test code
      C.1 Introduction
      C.2 Determination of sound power level
      C.3 Determination of emission sound pressure levels
          C.3.1 Determination of the emission sound pressure level
                at specified measuring points
          C.3.2 Determination of emission sound pressure level at
                work stations
      C.4 Measurement uncertainty
      C.5 Operating conditions
      C.6 Information to be recorded and reported
      C.7 Declaration and verification of noise emission values
Annex ZA (informative) Relationship between this European Standard
         and the Essential Requirements of EU Directive 98/37/EC
Annex ZB (informative) Relationship between this European Standard
         and the Essential Requirements of EU Directive 2006/42/EC
Bibliography
National Annex NA (informative) Bibliography

Defines the safety requirements to be met during design, assembly, transport, commissioning, operation, maintenance and decommissioning of the equipment.

DocumentType	Standard
Pages	49
PublisherName	German Institute for Standardisation (Deutsches Institut für Normung)
Status	Current

Standards	Relationship
EN 14753:2007	Identical

EN 294:1992/AC:1993	SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE UPPER LIMBS
ISO 11202:2010	Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections
EN 894-3:2000+A1:2008	Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators
EN 12464-1:2011	Light and lighting - Lighting of work places - Part 1: Indoor work places
EN 982:1996+A1:2008	Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics
ISO 4871:1996	Acoustics — Declaration and verification of noise emission values of machinery and equipment
EN 1037:1995+A1:2008	Safety of machinery - Prevention of unexpected start-up
ISO 14122-3:2016	Safety of machinery — Permanent means of access to machinery — Part 3: Stairs, stepladders and guard-rails
PREN 15004-1 : DRAFT 2016	FIXED FIREFIGHTING SYSTEMS - GAS EXTINGUISHING SYSTEMS - PART 1: DESIGN, INSTALLATION AND MAINTENANCE (ISO 14520-1:2015, MODIFIED)
ISO 14122-1:2016	Safety of machinery — Permanent means of access to machinery — Part 1: Choice of fixed means and general requirements of access
EN 1088:1995+A2:2008	Safety of machinery - Interlocking devices associated with guards - Principles for design and selection
IEC 61310-2:2007	Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking
EN 981:1996+A1:2008	Safety of machinery - System of auditory and visual danger and information signals
ISO/TR 11688-1:1995	Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning
ISO 5598:2008	Fluid power systems and components Vocabulary
EN 61310-2:2008	Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking
EN 12094-1:2003	Fixed firefighting systems - Components for gas extinguishing systems - Part 1: Requirements and test methods for electrical automatic control and delay devices
ISO 13732-1:2006	Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces
EN 614-2:2000+A1:2008	Safety of machinery - Ergonomic design principles - Part 2: Interactions between the design of machinery and work tasks
EN 1837:1999+A1:2009	Safety of machinery - Integral lighting of machines
EN 811 : 1996	SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE LOWER LIMBS
EN 349:1993+A1:2008	Safety of machinery - Minimum gaps to avoid crushing of parts of the human body
EN 13478:2001+A1:2008	Safety of machinery - Fire prevention and protection
IEC 60204-1:2016	Safety of machinery - Electrical equipment of machines - Part 1: General requirements
EN ISO 13850:2015	Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015)
EN 1050 : 1996	SAFETY OF MACHINERY - PRINCIPLES FOR RISK ASSESSMENT
EN ISO 7731:2008	Ergonomics - Danger signals for public and work areas - Auditory danger signals (ISO 7731:2003)
EN ISO 11820 : 1996	ACOUSTICS - MEASUREMENTS ON SILENCERS IN SITU
EN 614-1:2006+A1:2009	Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles
EN ISO 11688-2 : 2000	ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 2: INTRODUCTION TO THE PHYSICS OF LOW-NOISE DESIGN
ISO 14122-4:2016	Safety of machinery — Permanent means of access to machinery — Part 4: Fixed ladders
ISO 7731:2003	Ergonomics Danger signals for public and work areas Auditory danger signals
EN 574:1996+A1:2008	Safety of machinery - Two-hand control devices - Functional aspects - Principles for design
EN ISO 13732-1:2008	Ergonomics of the thermal environment - Methods for the assessment of human responses to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1:2006)
ISO 11820:1996	Acoustics — Measurements on silencers in situ
EN 626-2:1996+A1:2008	Safety of machinery - Reduction of risk to health from hazardous substances emitted by machinery - Part 2: Methodology leading to verification procedures
IEC 60405:2003	Nuclear instrumentation - Constructional requirements and classification of radiometric gauges
EN ISO 12100-1:2003/A1:2009	SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY
EN ISO 14122-3:2016	Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2016)
EN 953:1997+A1:2009	Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards
EN 842:1996+A1:2008	Safety of machinery - Visual danger signals - General requirements, design and testing
EN ISO 14122-4:2016	Safety of machinery - Permanent means of access to machinery - Part 4: Fixed ladders (ISO 14122-4:2016)
EN ISO 14122-2:2016	Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways (ISO 14122-2:2016)
ISO 12100-2:2003	Safety of machinery Basic concepts, general principles for design Part 2: Technical principles
EN ISO 12100-2:2003/A1:2009	SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES
EN ISO 6682:2008	Earth-moving machinery - Zones of comfort and reach for controls (ISO 6682:1986, including Amd 1:1989)
ISO 14520-1:2015	Gaseous fire-extinguishing systems — Physical properties and system design — Part 1: General requirements
EN 983:1996+A1:2008	Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics
ISO 11064-1:2000	Ergonomic design of control centres Part 1: Principles for the design of control centres
EN ISO 6743-4:2015	Lubricants, industrial oils and related products (class L) - Classification - Part 4: Family H (Hydraulic systems) (ISO 6743-4:2015)
ISO 12100-1:2003	Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology
EN ISO 13849-1:2015	Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015)
ISO 13850:2015	Safety of machinery Emergency stop function Principles for design
DIN VDE 0412-1 : 1998	NUCLEAR INSTRUMENTATION - ELECTRICAL MEASURING SYSTEMS AND INSTRUMENTS UTILIZING IONIZING RADIATION SOURCES - PART 1: TECHNOLOGICAL SAFETY REQUIREMENTS
EN ISO 4871:2009	Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)
ISO 11546-1:1995	Acoustics Determination of sound insulation performances of enclosures Part 1: Measurements under laboratory conditions (for declaration purposes)
IEC 61310-1:2007	Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals
EN 50171 : 2001 COR 2001	CENTRAL POWER SUPPLY SYSTEMS
EN 626-1:1994+A1:2008	Safety of machinery - Reduction of risks to health from hazardous substances emitted by machinery - Part 1: Principles and specifications for machinery manufacturers
EN ISO 11064-1:2000	Ergonomic design of control centres - Part 1: Principles for the design of control centres (ISO 11064-1:2000)
EN ISO 11691:2009	Acoustics - Measurement of insertion loss of ducted silencers without flow - Laboratory survey method (ISO 11691:1995)
EN ISO 11821 : 1997	ACOUSTICS - MEASUREMENT OF THE IN SITU SOUND ATTENUATION OF A REMOVABLE SCREEN
ISO 7000:2014	Graphical symbols for use on equipment Registered symbols
EN ISO 11546-1:2009	Acoustics - Determination of sound insulation performances of enclosures - Part 1: Measurements under laboratory conditions (for declaration purposes) (ISO 11546-1:1995)
ISO 14122-2:2016	Safety of machinery — Permanent means of access to machinery — Part 2: Working platforms and walkways
EN ISO 11688-1:2009	Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995)
EN ISO 14122-1:2016	Safety of machinery - Permanent means of access to machinery - Part 1: Choice of fixed means and general requirements of access (ISO 14122-1:2016)
ISO 13849-1:2015	Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design
ISO/TR 11688-2:1998	Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design
EN 61310-1:2008	Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals
EN ISO 11202:2010	Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010)
ISO 11691:1995	Acoustics Measurement of insertion loss of ducted silencers without flow Laboratory survey method
ISO 6743-4:2015	Lubricants, industrial oils and related products (class L) Classification Part 4: Family H (Hydraulic systems)
ISO 7745:2010	Hydraulic fluid power — Fire-resistant (FR) fluids — Requirements and guidelines for use
ISO 11821:1997	Acoustics — Measurement of the in situ sound attenuation of a removable screen
EN 60204-1 : 2006 COR 2010	SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS

View more information

US$149.99

Excluding Tax where applicable

Product format

I agree to the DRM document license rules apply against the PDF selection made.

Please confirm that you agree to the document license rules for this document.

I agree to the document license rules .

Please confirm that you agree to the document license rules for this document.

Access your standards online with a subscription

Features

Simple online access to standards, technical information and regulations.
Critical updates of standards and customisable alerts and notifications.
Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

Get in touch with us

Log into your Account

DIN EN 14753 E : 2008

Current

Table of Contents

Abstract

General Product Information

International Equivalents

Standards Referencing This Book

Category

Subcategory

Access your standards online with a subscription