Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012)

Available format(s)

Hardcopy , PDF

Language(s)

English, German

Published date

06-01-2012

Publisher

German Institute for Standardisation (Deutsches Institut für Normung)

DevelopmentNote	Together with DIN EN ISO 527-1 E supersedes DIN 53455 E. (11/1999) Supersedes DIN 53457 E (08/2002)
DocumentType	Standard
Pages	18
PublisherName	German Institute for Standardisation (Deutsches Institut für Normung)
Status	Current
Supersedes	DIN EN ISO 527-2:1996-07

Standards	Relationship
UNE-EN ISO 527-2:1997	Identical
SN EN ISO 527-2:2012	Identical
BS EN ISO 527-2:1996	Identical
NS EN ISO 527-2 : 2012	Identical
NF EN ISO 527-2 : 2012	Identical
I.S. EN ISO 527-2:2012	Identical
EN ISO 527-2:2012	Identical
NEN EN ISO 527-2 : 2012	Identical
UNI EN ISO 527-2 : 2012	Identical
ISO 527-2:2012	Identical
NBN EN ISO 527-2 : 2012	Identical

DIN EN ISO 11833-1:2012-11	PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS - PART 1: SHEETS OF THICKNESS NOT LESS THAN 1 MM (ISO 11833-1:2012)
DIN EN ISO 80369-7:2017-10	Small-bore connectors for liquids and gases in healthcare applications - Part 7: Connectors for intravascular or hypodermic applications (ISO 80369-7:2016, Corrected version 2016-12-01)
DIN EN ISO 11296-7:2013-05	PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 7: LINING WITH SPIRALLY-WOUND PIPES (ISO 11296-7:2011)
DIN ISO 23013:2017-10	ROAD VEHICLES - DETERMINATION OF RESISTANCE TO FORCED ENTRY OF SECURITY GLASS CONSTRUCTIONS USED IN VEHICLE GLAZING - TEST OF GLAZING SYSTEMS (ISO 23013:2016)
DIN EN ISO 14910-2:2013-06	PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 14910-2:2013)
DIN EN ISO 15013:2008-01	Plastics - Extruded sheets of polypropylene (PP) - Requirements and test methods (ISO 15013:2007); German version EN ISO 15013:2007
DIN ISO 11040-4:2017-07	PREFILLED SYRINGES - PART 4: GLASS BARRELS FOR INJECTABLES AND STERILIZED SUBASSEMBLED SYRINGES READY FOR FILLING (ISO 11040-4:2015)
DIN EN ISO 3672-2:2002-07	PLASTICS - UNSATURATED-POLYESTER RESINS (UP-R) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
DIN EN ISO 11439:2013-09	Gas cylinders - High pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles (ISO 11439:2013)
DIN EN 12864 E : 2006 AMD 3 2010	LOW PRESSURE, NON ADJUSTABLE REGULATORS HAVING A MAXIMUM OUTLET PRESSURE OF LESS THAN OR EQUAL TO 200 MBAR, WITH A CAPACITY OF LESS THAN OR EQUAL TO 4 KG/H, AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES
DIN EN ISO 11963:2013-03	PLASTICS - POLYCARBONATE SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS (ISO 11963:2012)
DIN EN 10288:2003-12	STEEL TUBES AND FITTINGS FOR ONSHORE AND OFFSHORE PIPELINES - EXTERNAL TWO-LAYER EXTRUDED POLYETHYLENE BASED COATINGS
DIN ISO 9523:2016-05	TOURING SKI-BOOTS FOR ADULTS - INTERFACE WITH TOURING SKI-BINDINGS - REQUIREMENTS AND TEST METHODS (ISO 9523:2015)
DIN 30678:2013-09	Polypropylene coatings on steel pipes and fittings - Requirements and testing
DIN EN ISO 12215-5:2014-10	SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 5: DESIGN PRESSURES FOR MONOHULLS, DESIGN STRESSES, SCANTLINGS DETERMINATION (ISO 12215-5:2008 + AMD 1:2014)
DIN EN ISO 6224:2012-02	Thermoplastics hoses, textile-reinforced, for general-purpose water applications - Specification (ISO 6224:2011)
DIN ISO 7148-2:2001-03	PLAIN BEARINGS - TESTING OF THE TRIBOLOGICAL BEHAVIOUR OF BEARING MATERIALS - PART 2: TESTING OF POLYMER-BASED PLAIN BEARING MATERIALS (ISO 7148-2:2012)

ISO 293:2004	Plastics — Compression moulding of test specimens of thermoplastic materials
ISO 3167:2014	Plastics Multipurpose test specimens
DIN ISO 5725-2:2002-12	Accuracy (trueness and precision) of measurement methods and results - Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method (ISO 5725-2:1994 including Technical Corrigendum 1:2002)
ISO 11403-3:2014	Plastics Acquisition and presentation of comparable multipoint data Part 3: Environmental influences on properties
ISO 294-3:2002	Plastics Injection moulding of test specimens of thermoplastic materials Part 3: Small plates
DIN EN ISO 2818:1997-06	PLASTICS - PREPARATION OF TEST SPECIMENS BY MACHINING
DIN EN ISO 11403-3 E : 2002	PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 3: ENVIRONMENTAL INFLUENCES ON PROPERTIES (ISO 11403-3:2014)
ISO 295:2004	Plastics — Compression moulding of test specimens of thermosetting materials
ISO 10724-1:1998	Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens
DIN EN ISO 295 E : 2004	PLASTICS - COMPRESSION MOULDING TEST SPECIMENS OF THERMOSETTING MATERIALS
ISO 1926:2009	Rigid cellular plastics Determination of tensile properties
ISO 294-2:1996	Plastics Injection moulding of test specimens of thermoplastic materials Part 2: Small tensile bars
ISO 5725-2:1994	Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method
ISO 294-1:2017	Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
ISO 37:2017	Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
ISO 2818:1994	Plastics — Preparation of test specimens by machining
DIN EN ISO 527-1:2012-06	PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 1: GENERAL PRINCIPLES (ISO 527-1:2012)
DIN EN ISO 293 E : 2005	PLASTICS - COMPRESSION MOULDING TEST SPECIMENS OF THERMOPLASTIC MATERIALS
ISO 20753:2008	Plastics Test specimens
ISO 527-1:2012	Plastics Determination of tensile properties Part 1: General principles