PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - UNPLASTICIZED POLYAMIDE (PA-U) PIPING SYSTEMS WITH FUSION JOINTING AND MECHANICAL JOINTING - PART 3: FITTINGS (ISO 16486-3:2012 + AMD 1:2014)

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-01-2015

Publisher

German Institute for Standardisation (Deutsches Institut für Normung)

National foreword
National Annex NA (informative) - Bibliography
Introduction
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviated
   terms
4 Material
5 General characteristics
6 Geometrical characteristics
7 Mechanical characteristics
8 Physical characteristics
9 Chemical resistance of fittings in contact with
   chemicals
10 Performance requirements
11 Marking
12 Packaging
Annex A (informative) - Examples of typical terminal
        connections for electrofusion fittings
Annex B (normative) - Short-term pressure test method
Annex C (normative) - Tensile test fitting/pipe assemblies
Bibliography

Defines the physical and mechanical properties of fittings made from unplasticized polyamide (PA-U) in accordance with ISO 16486-1, intended to be buried and used for the supply of gaseous fuels.

DocumentType	Standard
Pages	23
PublisherName	German Institute for Standardisation (Deutsches Institut für Normung)
Status	Current

Standards	Relationship
ISO 16486-3:2012	Identical

EN 682:2002/A1:2005	ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR SEALS USED IN PIPES AND FITTINGS CARRYING GAS AND HYDROCARBON FLUIDS
ISO 16486-5:2012	Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing Part 5: Fitness for purpose of the system
ISO 13953:2001	Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
ISO 13956:2010	Plastics pipes and fittings Decohesion test of polyethylene (PE) saddle fusion joints Evaluation of ductility of fusion joint interface by tear test
ISO 1167-4:2007	Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies
ISO 4433-1:1997	Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 1: Immersion test method
ISO 13957:1997	Plastics pipes and fittings — Polyethylene (PE) tapping tees — Test method for impact resistance
DIN ISO 16486-1 E : 2015	PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - UNPLASTICIZED POLYAMIDE (PA-U) PIPING SYSTEMS WITH FUSION JOINTING AND MECHANICAL JOINTING - PART 1: GENERAL (ISO 16486-1:2012 + AMD 1:2014)
IEC 60364-1:2005	Low-voltage electrical installations - Part 1: Fundamental principles, assessment of general characteristics, definitions
ISO 3126:2005	Plastics piping systems Plastics components Determination of dimensions
ISO 11922-1:1997	Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV	Degrees of protection provided by enclosures (IP Code)
ISO 13954:1997	Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
ISO 307:2007	Plastics Polyamides Determination of viscosity number
ISO 291:2008	Plastics Standard atmospheres for conditioning and testing
ISO 13955:1997	Plastics pipes and fittings Crushing decohesion test for polyethylene (PE) electrofusion assemblies
ISO 16486-2:2012	Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing Part 2: Pipes
DIN ISO 16486-2 E : 2015	PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - UNPLASTICIZED POLYAMIDE (PA-U) PIPING SYSTEMS WITH FUSION JOINTING AND MECHANICAL JOINTING - PART 2: PIPES (ISO 16486-2:2012 + AMD 1:2014)
ISO 16486-1:2012	Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing Part 1: General
ISO 13951:2015	Plastics piping systems Test method for the resistance of plastic pipe/pipe or pipe/fitting assemblies to tensile loading
DIN ISO 16486-5 E : 2015	PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - UNPLASTICIZED POLYAMIDE (PA-U) PIPING SYSTEMS WITH FUSION JOINTING AND MECHANICAL JOINTING - PART 5: FITNESS FOR PURPOSE OF THE SYSTEM (ISO 16486-5:2012)
ISO 1167-1:2006	Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method

View more information

US$98.87

Excluding Tax where applicable

Product format

I agree to the DRM document license rules apply against the PDF selection made.

Please confirm that you agree to the document license rules for this document.

I agree to the document license rules .

Please confirm that you agree to the document license rules for this document.

Access your standards online with a subscription

Features

Simple online access to standards, technical information and regulations.
Critical updates of standards and customisable alerts and notifications.
Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

Get in touch with us

DIN ISO 16486-3 E : 2015

PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - UNPLASTICIZED POLYAMIDE (PA-U) PIPING SYSTEMS WITH FUSION JOINTING AND MECHANICAL JOINTING - PART 3: FITTINGS (ISO 16486-3:2012 + AMD 1:2014)

Table of Contents

Abstract

General Product Information

International Equivalents

Standards Referencing This Book

Category

Subcategory