EEMUA 153 : 96 AMD 1 2002

FOREWORD
CHAPTER 1: SCOPE AND DEFINITIONS
    300 GENERAL STATEMENTS
    300.4 Status of Appendices
CHAPTER II: DESIGN
    301 DESIGN CONDITIONS
    301.1 General
    301.2 Design Pressure
    301.2.1 General
    301.3 Design Temperature
    302 DESIGN CRITERIA
    306 FITTINGS, BENDS, MITERS, LAPS AND BRANCH
              CONNECTIONS
    308 FLANGES, BLANKS, FLANGE FACINGS AND GASKETS
    308.2 Specific Requirements for Flanges
    308.2.1 Slip-on Flanges
    314 THREADED JOINTS
    314.2.1 Taper-Threaded Joints
    319 PIPING FLEXIBILITY
    319.2.3 Displacement Stress Range
    321 PIPING SUPPORT
    321.1.5 Threads
    322 SPECIFIC PIPING SYSTEMS
    322.6 Pressure Relieving Systems
    322.6.3 Pressure Relieving Devices
CHAPTER III: MATERIALS
    323 GENERAL REQUIREMENTS
    323.2 Temperature Limitations
    323.2.2 Lower Temperature Limits, Listed Materials
    323.2.3 Temperature Limits, Unlisted Materials
    323.3 Impact Testing Methods and Acceptance Criteria
    323.3.1 General
CHAPTER V: FABRICATION, ASSEMBLY AND ERECTION
    328 WELDING
    328.2.1 Qualification Requirements
    328.3.2 Weld Backing Material
    328.3.3 Consumable Inserts
CHAPTER VI: INSPECTION, EXAMINATION AND TESTING
    340 INSPECTION
    340.4 Qualifications of the Owner's Inspector
    341 EXAMINATION
    341.3 Examination Requirements
    341.3.1 General
    341.4.2 Examination - Category D Fluid Service
    343 EXAMINATION PROCEDURES
    344 TYPES OF EXAMINATION
    345 TESTING
    345.1 Required Leak Test
    345.7 Initial Service Leak Test
    345.9 Alternative Leak Test
CHAPTER VII: NONMETALLIC PIPING AND PIPING LINED WITH
              NONMETALS
CHAPTER VIII: PIPING FOR CATEGORY M FLUID SERVICE
CHAPTER IX: HIGH PRESSURE PIPING
    K300 GENERAL STATEMENTS
APPENDIX A: ALLOWABLE STRESSES AND QUALITY FACTORS FOR
              METALLIC PIPING AND BOLTING MATERIALS
              NOTES FOR APPENDIX A TABLES
APPENDIX B: STRESS TABLES AND ALLOWABLE PRESSURE TABLES
              FOR NONMETALS
APPENDIX C: PHYSICAL PROPERTIES OF PIPING MATERIALS
APPENDIX G: SAFEGUARDING
    G300 GENERAL
APPENDIX SA: REQUIREMENTS FOR CARBON, CARBON-MANGANESE AND
              SOME LOW ALLOY STEEL PIPING FOR APPLICATION
              BELOW 0 DEG C
         SA1 SCOPE
         SA2 GENERAL REQUIREMENTS
         SA3 NOTCH DUCTILITY REQUIREMENTS
         SA4 DESIGNED PARAMETERS
              SA4.1 Design Reference Temperature
              SA4.2 Material Reference Temperature
              SA4.3 Reference Thickness
                     SA4.3.1 Butt Welding Piping Components
                     SA4.3.2 Socket Welding Piping Components
                     SA4.3.3 Weld Neck Flanges, Plate and
                              Slip-on (or hubbed) Flanges
                     SA4.3.4 Branches and Reinforcement Rings
                     SA4.3.5 Attachments
                     SA4.3.6 Unwelded Components
         SA5 ALLOWABLE DISPLACEMENT STRESS RANGE FOR COLD
              DUTIES
         SA6 IMPACT TESTING
              SA6.1 General
              SA6.2 Impact Test Requirements at Material
                     Reference Temperature
                     SA6.2.1 Attachments
                     SA6.2.2 Castings
                     SA6.2.3 Welds
                              SA6.2.3.1 Testing of Welds
                              SA6.2.3.2 Weld Procedure
                                         Qualification Test
                                         Pieces
                              SA6.2.3.3 Position of Impact
                                         Test Specimens
                              SA6.2.3.4 Required Impact
                                         Values
                              SA6.2.3.5 Heat Affected Zones
                              SA6.2.3.6 Retests
              SA6.3 Bolting
         SA7 DESIGN, MANUFACTURE AND WORKMANSHIP
              SA7.1 Design
              SA7.2 Manufacture
              SA7.3 Heat Treatment of Piping Components
              SA7.4 Welding
Figure SA(1) Permissible design reference temperature/
              reference thickness/material reference
              temperature relationships for as-welded piping
              components
Figure SA(2) Permissible design reference temperature (etc.)
              relationships for post-weld heat treated
              piping components
figure SA(3) Reference thickness: flanges and flat ends
APPENDIX SB: WORKED EXAMPLES RELATING TO APPENDIX SA
     INTRODUCTION
     EXAMPLE 1
     EXAMPLE 2
     EXAMPLE 3
     EXAMPLE 4
     EXAMPLE 5
EEMUA PUBLICATIONS - SUMMARY LIST