• There are no items in your cart

EN 10346:2015

Current
Current

The latest, up-to-date edition.

Continuously hot-dip coated steel flat products for cold forming - Technical delivery conditions
Published date

07-15-2015

European foreword
1 Scope
2 Normative References
3 Terms and definitions
4 Classification and designation
5 Information to be supplied by the purchaser
6 Manufacturing and processing
7 Requirements
8 Inspection
9 Marking
10 Packing
11 Storage and transportation
Annex A (normative) - Reference method for determination
        of the zinc, zinc-iron, zinc-aluminium, zinc-magnesium
        and aluminium-zinc coating mass
Annex B (normative) - Reference method for determination
        of the aluminium-silicon coating mass
Annex C (normative) - Method for determination of the mass
        of the Al-Fe-Si alloy layer
Annex D (informative) - Technical changes from the previous
        edition
Bibliography

This European Standard specifies requirements for continuously hot-dip coated products made of low carbon steels for cold forming, of steels for construction, of steels with high proof strength for cold forming and coated with zinc (Z), zinc-iron alloy (ZF), zinc-aluminium alloy (ZA), aluminium-zinc alloy (AZ), aluminium-silicon alloy (AS) or zinc-magnesium alloy (ZM) and for continuously hot-dip coated products made of multiphase steels for cold forming coated with zinc (Z), zinc-iron alloy (ZF), zinc-aluminium alloy (ZA) or zinc-magnesium alloy (ZM) in thicknesses of 0,20 mm ≤ t < 3,0 mm.

By agreement at the time of enquiry and order, this European Standard is applicable to continuously hot-dip coated flat products of an expanded validity range defined for thicknesses t < 0,20mm or in thicknesses 3,0mm < t < 6,5mm with agreed mechanical properties and test specimens, adhesion of coating and surface condition requirements.

The thickness is the final thickness of the delivered product after coating.

This document applies to strip of all widths and to sheets cut from it (≥ 600 mm width) and cut lengths

(< 600 mm width).

NOTE 1Products coated with (pure) aluminium can also be available, but are not covered by this European standard.

NOTE 2The products covered by this European Standard are used where cold formability, high strength, a defined minimum yield strength and corrosion resistance are the most important factors. Corrosion resistance of the product is proportional to the coating thickness, hence to its mass (see also 7.3.2). The products covered by this European Standard can be used as substrates for organic coated flat products specified in EN 10169 for building and general engineering applications.

NOTE 3By agreement at the time of enquiry and order, this European standard is applicable to other continuously hot-dip coated hot rolled steel flat products (e.g. in accordance with EN 10149-2).

Committee
CEN/TC 459/SC 9
DevelopmentNote
Supersedes EN 10292, EN 10326 and EN 10327. Together with EN 10152 supersedes EN 10336. (03/2009) Supersedes FORD WSD M1A295 A1/A2/A3 & FORD WSA M1A297 A1. (12/2014) Supersedes PREN 10346. (07/2015)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current
Supersedes

Standards Relationship
UNI EN 10346:2015 Identical
I.S. EN 10346:2015 Identical
PN EN 10346 : 2015 Identical
DIN EN 10346:2015-10 Identical
NEN EN 10346 : 2015 Identical
BS EN 10346:2015 Identical
UNE-EN 10346:2015 Identical
NF EN 10346 : 2015 Identical
NBN EN 10346 : 2015 Identical
UNI EN 10346 : 2009 Identical
SN EN 10346:2015 Identical
NS EN 10346 : 2015 Identical

PREN 13658-2 : DRAFT 2017 METAL LATH AND BEADS - DEFINITIONS, REQUIREMENTS AND TEST METHODS - PART 2: EXTERNAL RENDERING
BS ISO 9364:2017 Steel sheet, 55 % aluminium-zinc alloy-coated by the continuous hot-dip process, of commercial, drawing and structural qualities
17/30355209 DC : 0 BS EN ISO 18592 - RESISTANCE WELDING - DESTRUCTIVE TESTING OF WELDS - METHOD FOR THE FATIGUE TESTING OF MULTI-SPOT-WELDED SPECIMENS
BS EN 14509:2013 Self-supporting double skin metal faced insulating panels. Factory made products. Specifications
DIN EN 10152:2009-07 ELECTROLYTICALLY ZINC COATED COLD ROLLED STEEL FLAT PRODUCTS FOR COLD FORMING - TECHNICAL DELIVERY CONDITIONS
DIN EN 13381-5:2015-02 TEST METHODS FOR DETERMINING THE CONTRIBUTION TO THE FIRE RESISTANCE OF STRUCTURAL MEMBERS - PART 5: APPLIED PROTECTION TO CONCRETE/PROFILED SHEET STEEL COMPOSITE MEMBER
I.S. EN ISO 14713-2:2009 ZINC COATINGS - GUIDELINES AND RECOMMENDATIONS FOR THE PROTECTION AGAINST CORROSION OF IRON AND STEEL IN STRUCTURES - PART 2: HOT DIP GALVANIZING
EN 15773:2018 Industrial application of powder organic coatings to hot dip galvanized or sherardized steel articles [duplex systems] - Specifications, recommendations and guidelines
13/30280536 DC : 0 BS ISO 4998 - CONTINUOUS HOT-DIP ZINC-COATED CARBON STEEL SHEET OF STRUCTURAL QUALITY
UNI EN 13381-5 : 2014 TEST METHODS FOR DETERMINING THE CONTRIBUTION TO THE FIRE RESISTANCE OF - STRUCTURAL MEMBERS - PART 5: APPLIED PROTECTION TO CONCRETE/PROFILED SHEET STEEL COMPOSITE MEMBER
12/30265747 DC : 0 BS EN 845-2 - SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 2: LINTELS
FD CEN/TR 16239 : 2011 FD INSTALLATION RULES OF FIBROUS (GYPSUM) PLASTER WORKS
15/30320416 DC : 0 BS EN 1090-2 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
11/30251991 DC : 0 BS EN 14195 - METAL FRAMING COMPONENTS FOR GYPSUM PLASTERBOARD SYSTEMS - DEFINITIONS, REQUIREMENTS AND TEST METHODS
BS EN 16475-3 : 2016 CHIMNEYS - ACCESSORIES - PART 3: DRAUGHT REGULATORS, STANDSTILL OPENING DEVICES AND COMBINED SECONDARY AIR DEVICES - REQUIREMENTS AND TEST METHODS
DIN EN 14509:2013-12 SELF-SUPPORTING DOUBLE SKIN METAL FACED INSULATING PANELS - FACTORY MADE PRODUCTS - SPECIFICATIONS
12/30265759 DC : 0 BS EN 845-3 - SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 3: BED JOINT REINFORCEMENT OF STEEL MESHWORK
PREN 14353 : DRAFT 2016 METAL BEADS AND FEATURE PROFILES FOR USE WITH GYPSUM PLASTERBOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS
PREN 845-1 : DRAFT 2012 SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 1: WALL TIES, TENSION STRAPS, HANGERS AND BRACKETS
12/30265756 DC : 0 BS EN 845-1 - SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 1: WALL TIES, TENSION STRAPS, HANGERS AND BRACKETS
17/30357663 DC : 0 BS ISO 5000 - STEEL SHEET, ALUMINIUM-SILICON ALLOY-COATED BY THE CONTINUOUS HOT-DIP PROCESS, OF COMMERCIAL AND DRAWING QUALITIES
PREN 13658-1 : DRAFT 2017 METAL LATH AND BEADS - DEFINITIONS, REQUIREMENTS AND TEST METHODS - PART 1: INTERNAL PLASTERING
PREN 16002 : DRAFT 2016 FLEXIBLE SHEETS FOR WATERPROOFING - DETERMINATION OF THE RESISTANCE TO WIND LOAD OF MECHANICALLY FASTENED FLEXIBLE SHEETS FOR ROOF WATERPROOFING
PREN 12574-2 : DRAFT 2015 STATIONARY WASTE CONTAINERS - PART 2: PERFORMANCE REQUIREMENTS AND TEST METHODS
15/30323520 DC : 0 BS EN 12574-2 - STATIONARY WASTE CONTAINERS - PART 2: PERFORMANCE REQUIREMENTS AND TEST METHODS
BS EN 10169 : 2010 CONTINUOUSLY ORGANIC COATED (COIL COATED) STEEL FLAT PRODUCTS - TECHNICAL DELIVERY CONDITIONS
DIN EN 14353 E : 2017 METAL BEADS AND FEATURE PROFILES FOR USE WITH GYPSUM PLASTERBOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS
UNE-EN 1317-5:2008 Road restraint systems - Part 5: Product requirements and evaluation of conformity for vehicle restraint systems
DIN EN 16002:2016-10 (Draft) FLEXIBLE SHEETS FOR WATERPROOFING - DETERMINATION OF THE RESISTANCE TO WIND LOAD OF MECHANICALLY FASTENED FLEXIBLE SHEETS FOR ROOF WATERPROOFING
I.S. EN 10169:2010 CONTINUOUSLY ORGANIC COATED (COIL COATED) STEEL FLAT PRODUCTS - TECHNICAL DELIVERY CONDITIONS
BS EN 14353 : 2007 METAL BEADS AND FEATURE PROFILES FOR USE WITH GYPSUM PLASTERBOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS
UNI EN 912 : 2011 TIMBER FASTENERS - SPECIFICATIONS FOR CONNECTORS FOR TIMBER
I.S. EN 16002:2010 FLEXIBLE SHEETS FOR WATERPROOFING - DETERMINATION OF THE RESISTANCE TO WIND LOAD OF MECHANICALLY FASTENED FLEXIBLE SHEETS FOR ROOF WATERPROOFING
BS EN ISO 18592:2009 Resistance welding. Destructive testing of welds. Method for the fatigue testing of multispot- welded specimens
EN 1995-1-1:2004/A2:2014 EUROCODE 5: DESIGN OF TIMBER STRUCTURES - PART 1-1: GENERAL - COMMON RULES AND RULES FOR BUILDINGS
DIN EN 12574-2:2015-08 (Draft) STATIONARY WASTE CONTAINERS - PART 2: PERFORMANCE REQUIREMENTS AND TEST METHODS
DIN EN 1317-5:2012-06 ROAD RESTRAINT SYSTEMS - PART 5: PRODUCT REQUIREMENTS AND EVALUATION OF CONFORMITY FOR VEHICLE RESTRAINT SYSTEMS
BS EN 845-2 : 2013 SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 2: LINTELS
BS EN 912:2011 Timber fasteners. Specifications for connectors for timbers
BS EN 1995-1-1 : 2012 EUROCODE 5: DESIGN OF TIMBER STRUCTURES - PART 1-1: GENERAL - COMMON RULES AND RULES FOR BUILDINGS
UNE-EN 505:2013 Roofing products from metal sheet - Specification for fully supported roofing products of steel sheet
BS EN 505:2013 Roofing products from metal sheet. Specification for fully supported roofing products of steel sheet
I.S. EN 912:2011 TIMBER FASTENERS - SPECIFICATIONS FOR CONNECTORS FOR TIMBERS
I.S. EN 13914-1:2016 DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 1: EXTERNAL RENDERING
DIN EN 14195:2015-03 METAL FRAMING COMPONENTS FOR GYPSUM BOARD SYSTEMS - DEFINITIONS, REQUIREMENTS AND TEST METHODS
DIN EN 508-1:2000-12 ROOFING AND CLADDING PRODUCTS FROM METAL SHEET - SPECIFICATION FOR SELF-SUPPORTING OF STEEL, ALUMINIUM OR STAINLESS STEEL SHEET - PART 1: STEEL
EN 12574-2:2017 Stationary waste containers - Part 2: Performance requirements and test methods
EN 10152:2017 Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions
EN 1075:2014 Timber structures - Test methods - Joints made with punched metal plate fasteners
DIN EN 1090-2:2011-10 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
UNI EN 508-1 : 2014 ROOFING AND CLADDING PRODUCTS FROM METAL SHEET - SPECIFICATION FOR SELF-SUPPORTING OF STEEL, ALUMINIUM OR STAINLESS STEEL SHEET - PART 1: STEEL
EN 13438:2013 Paints and varnishes - Powder organic coatings for hot dip galvanised or sherardised steel products for construction purposes
EN 10169:2010+A1:2012 Continuously organic coated (coil coated) steel flat products - Technical delivery conditions
EN 13381-5:2014 Test methods for determining the contribution to the fire resistance of structural members - Part 5: Applied protection to concrete/profiled sheet steel composite member
I.S. EN 16475-2:2017 CHIMNEYS - ACCESSORIES - PART 2: CHIMNEY FANS - REQUIREMENTS AND TEST METHODS
DIN EN ISO 14713-2 E : 2010 ZINC COATINGS - GUIDELINES AND RECOMMENDATIONS FOR THE PROTECTION AGAINST CORROSION OF IRON AND STEEL IN STRUCTURES - PART 2: HOT DIP GALVANIZING
13/30266550 DC : 0 BS EN 14509 - SELF-SUPPORTING DOUBLE SKIN METAL FACED INSULATING PANELS - FACTORY MADE PRODUCTS - SPECIFICATIONS
13/30265753 DC : 0 BS EN 13914-2 - DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 2: DESIGN CONSIDERATIONS AND ESSENTIAL PRINCIPLES FOR INTERNAL PLASTERING
17/30334103 DC : 0 BS ISO 9364 - CONTINUOUS HOT-DIP 55% ALUMINIUM/ZINC ALLOY-COATED STEEL SHEET OF COMMERCIAL, DRAWING AND STRUCTURAL QUALITIES
PREN 1317-5 : DRAFT 2013 ROAD RESTRAINT SYSTEMS - PART 5: PRODUCT REQUIREMENTS, TEST AND ASSESSMENT METHODS AND ACCEPTANCE CRITERIA
15/30327671 DC : 0 BS EN 10152 - ELECTROLYTICALLY ZINC COATED COLD ROLLED STEEL FLAT PRODUCTS FOR COLD FORMING - TECHNICAL DELIVERY CONDITIONS
17/30337809 DC : DRAFT JAN 2017 BS EN 15512 - STEEL STATIC STORAGE SYSTEMS - ADJUSTABLE PALLET RACKING SYSTEMS - PRINCIPLES FOR STRUCTURAL DESIGN
PREN 1090-2 : DRAFT 2015 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
UNE-EN 1090-2:2011 Execution of steel structures and aluminium structures - Part 2: Technical requirements for steel structures
PREN 14783 : DRAFT 2012 FULLY SUPPORTED METAL SHEET AND STRIP FOR ROOFING, EXTERNAL CLADDING AND INTERNAL LINING - PRODUCT SPECIFICATION AND REQUIREMENTS
ISO 9364:2017 Steel sheet, 55 % aluminium-zinc alloy-coated by the continuous hot-dip process, of commercial, drawing and structural qualities
EN 16002:2010 Flexible sheets for waterproofing - Determination of the resistance to wind load of mechanically fastened flexible sheets for roof waterproofing
UNI EN ISO 14713-2 : 2010 ZINC COATINGS - GUIDELINES AND RECOMMENDATIONS FOR THE PROTECTION AGAINST CORROSION OF IRON AND STEEL IN STRUCTURES - PART 2: HOT DIP GALVANIZING
BS EN 1090-2 : 2008 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
DIN EN 1090-2:2015-07 (Draft) EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
UNI EN 1090-2 : 2011 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
I.S. EN 14353:2017 METAL BEADS AND FEATURE PROFILES FOR USE WITH GYPSUM PLASTERBOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS
EN ISO 14713-2:2009 Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 2: Hot dip galvanizing (ISO 14713-2:2009)
ISO 4998:2014 Continuous hot-dip zinc-coated and zinc-iron alloy-coated carbon steel sheet of structural quality
DIN EN 1075:2015-03 TIMBER STRUCTURES - TEST METHODS - JOINTS MADE WITH PUNCHED METAL PLATE FASTENERS
DIN EN 13438:2013-12 PAINTS AND VARNISHES - POWDER ORGANIC COATINGS FOR HOT DIP GALVANISED OR SHERARDISED STEEL PRODUCTS FOR CONSTRUCTION PURPOSES
DIN EN 505:2013-06 ROOFING PRODUCTS FROM METAL SHEET - SPECIFICATION FOR FULLY SUPPORTED ROOFING PRODUCTS OF STEEL SHEET
BS EN 14195:2014 Metal framing components for gypsum board systems. Definitions, requirements and test methods
BS EN 13914-2:2016 Design, preparation and application of external rendering and internal plastering Internal plastering
BS EN 12574-2:2017 Stationary waste containers Performance requirements and test methods
BS EN ISO 1514:2004 Paints and varnishes. Standard panels for testing
I.S. EN 12574-2:2017 STATIONARY WASTE CONTAINERS - PART 2: PERFORMANCE REQUIREMENTS AND TEST METHODS
I.S. EN 1317-5:2007 ROAD RESTRAINT SYSTEMS - PART 5: PRODUCT REQUIREMENTS AND EVALUATION OF CONFORMITY FOR VEHICLE RESTRAINT SYSTEMS
DIN EN 12574-2:2017-05 STATIONARY WASTE CONTAINERS - PART 2: PERFORMANCE REQUIREMENTS AND TEST METHODS
EN 508-1:2014 Roofing and cladding products from metal sheet - Specification for self-supporting of steel, aluminium or stainless steel sheet - Part 1: Steel
I.S. EN 10152:2017 ELECTROLYTICALLY ZINC COATED COLD ROLLED STEEL FLAT PRODUCTS FOR COLD FORMING - TECHNICAL DELIVERY CONDITIONS
DIN EN 13611:2019-06 Safety and control devices for burners and appliances burning gaseous and/or liquid fuels - General requirements
I.S. EN 505:2013 ROOFING PRODUCTS FROM METAL SHEET - SPECIFICATION FOR FULLY SUPPORTED ROOFING PRODUCTS OF STEEL SHEET
I.S. EN 14783:2013 FULLY SUPPORTED METAL SHEET AND STRIP FOR ROOFING, EXTERNAL CLADDING AND INTERNAL LINING - PRODUCT SPECIFICATION AND REQUIREMENTS
I.S. EN 845-2:2013 SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 2: LINTELS
I.S. EN 508-1:2014 ROOFING AND CLADDING PRODUCTS FROM METAL SHEET - SPECIFICATION FOR SELF-SUPPORTING OF STEEL, ALUMINIUM OR STAINLESS STEEL SHEET - PART 1: STEEL
I.S. EN 13438:2013 PAINTS AND VARNISHES - POWDER ORGANIC COATINGS FOR HOT DIP GALVANISED OR SHERARDISED STEEL PRODUCTS FOR CONSTRUCTION PURPOSES
I.S. EN 845-3:2013 SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 3: BED JOINT REINFORCEMENT OF STEEL MESHWORK
I.S. EN 14195:2014 METAL FRAMING COMPONENTS FOR GYPSUM BOARD SYSTEMS - DEFINITIONS, REQUIREMENTS AND TEST METHODS
I.S. EN 1075:2014 TIMBER STRUCTURES - TEST METHODS - JOINTS MADE WITH PUNCHED METAL PLATE FASTENERS
I.S. EN 13914-2:2016 DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 2: INTERNAL PLASTERING
I.S. EN ISO 1514:2016 PAINTS AND VARNISHES - STANDARD PANELS FOR TESTING (ISO 1514:2016)
I.S. EN 13964:2014 SUSPENDED CEILINGS - REQUIREMENTS AND TEST METHODS
I.S. EN 845-1:2013 SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 1: WALL TIES, TENSION STRAPS, HANGERS AND BRACKETS
DIN EN ISO 18592:2010-05 RESISTANCE WELDING - DESTRUCTIVE TESTING OF WELDS - METHOD FOR THE FATIGUE TESTING OF MULTI-SPOT-WELDED SPECIMENS
DIN EN 10169:2012-06 Continuously organic coated (coil coated) steel flat products - Technical delivery conditions (includes Amendment A1:2012)
12/30264367 DC : 0 BS EN 505 - ROOFING PRODUCTS FROM METAL SHEET - SPECIFICATION FOR FULLY SUPPORTED ROOFING PRODUCTS OF STEEL SHEET
I.S. EN 15773:2018 INDUSTRIAL APPLICATION OF POWDER ORGANIC COATINGS TO HOT DIP GALVANIZED OR SHERARDIZED STEEL ARTICLES [DUPLEX SYSTEMS] - SPECIFICATIONS, RECOMMENDATIONS AND GUIDELINES
12/30264370 DC : 0 BS EN 14783 - FULLY SUPPORTED METAL SHEET AND STRIP FOR ROOFING, EXTERNAL CLADDING AND INTERNAL LINING - PRODUCT SPECIFICATION AND REQUIREMENTS
16/30323507 DC : 0 BS EN 15773 - INDUSTRIAL APPLICATION OF POWDER ORGANIC COATINGS TO HOT DIP GALVANIZED OR SHERARDIZED STEEL ARTICLES [DUPLEX SYSTEMS] - SPECIFICATIONS, RECOMMENDATIONS AND GUIDELINES
11/30234437 DC : 0 BS ISO 9364 - CONTINUOUS HOT-DIP 55% ALUMINIUM/ZINC ALLOY-COATED STEEL SHEET OF COMMERCIAL, DRAWING AND STRUCTURAL QUALITIES
PREN 14782 : DRAFT 2015 SELF-SUPPORTING METAL SHEET FOR ROOFING, EXTERNAL CLADDING AND INTERNAL LINING - PRODUCT SPECIFICATION AND REQUIREMENTS
12/30265304 DC : 0 BS EN 124-3 - GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS - PART 3: GULLY TOPS AND MANHOLE TOPS MADE FROM STEEL OR ALUMINIUM ALLOY
BS EN ISO 14713-2:2009 Zinc coatings. Guidelines and recommendations for the protection against corrosion of iron and steel in structures Hot dip galvanizing
UNE-EN 13381-5:2016 Test methods for determining the contribution to the fire resistance of structural members - Part 5: Applied protection to concrete/profiled sheet steel composite member
CEN/TR 16239:2011 Installation rules of fibrous (gypsum) plaster works
14/30297831 DC : 0 BS EN 1090-4 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 4: TECHNICAL REQUIREMENTS FOR THIN-GAUGE, COLD-FORMED STEEL ELEMENTS AND STRUCTURES FOR ROOF, CEILING, FLOOR AND WALL APPLICATIONS
PREN 14509 : DRAFT 2013 SELF-SUPPORTING DOUBLE SKIN METAL FACED INSULATING PANELS - FACTORY MADE PRODUCTS - SPECIFICATIONS
PREN 505 : DRAFT 2012 ROOFING PRODUCTS FROM METAL SHEET - SPECIFICATION FOR FULLY SUPPORTED ROOFING PRODUCTS OF STEEL SHEET
UNI EN 16002 : 2010 FLEXIBLE SHEETS FOR WATERPROOFING - DETERMINATION OF THE RESISTANCE TO WIND LOAD OF MECHANICALLY FASTENED FLEXIBLE SHEETS FOR ROOF WATERPROOFING
EN 1090-2:2008+A1:2011 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
UNE-EN ISO 14713-2:2011 Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 2: Hot dip galvanizing (ISO 14713-2:2009)
UNE-EN 14353:2017 Metal beads and feature profiles for use with gypsum plasterboards - Definitions, requirements and test methods
PREN 1090-4 : DRAFT 2014 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 4: TECHNICAL REQUIREMENTS FOR THIN-GAUGE, COLD-FORMED STEEL ELEMENTS AND STRUCTURES FOR ROOF, CEILING, FLOOR AND WALL APPLICATIONS
ISO 5000:2011 Continuous hot-dip aluminium-silicon-coated cold-reduced carbon steel sheet of commercial and drawing qualities
I.S. EN 14509:2013 SELF-SUPPORTING DOUBLE SKIN METAL FACED INSULATING PANELS - FACTORY MADE PRODUCTS - SPECIFICATIONS
DIN EN 508-1:2014-08 Roofing and cladding products from metal sheet - Specification for self-supporting of steel, aluminium or stainless steel sheet - Part 1: Steel
DIN EN 13914-1:2016-09 DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 1: EXTERNAL RENDERING
DIN EN 13914-2:2016-09 DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 2: INTERNAL PLASTERING
DIN EN 13964:2014-08 SUSPENDED CEILINGS - REQUIREMENTS AND TEST METHODS
DIN EN 14783 E : 2013 FULLY SUPPORTED METAL SHEET AND STRIP FOR ROOFING, EXTERNAL CLADDING AND INTERNAL LINING - PRODUCT SPECIFICATION AND REQUIREMENTS
UNE-EN 14509:2014 Self-supporting double skin metal faced insulating panels - Factory made products - Specifications
EN 13914-1:2016 Design, preparation and application of external rendering and internal plastering - Part 1: External rendering
EN 13964:2014 Suspended ceilings - Requirements and test methods
UNI EN 14509 : 2013 SELF-SUPPORTING DOUBLE SKIN METAL FACED INSULATING PANELS - FACTORY MADE PRODUCTS - SPECIFICATIONS
UNI EN 14783 : 2013 FULLY SUPPORTED METAL SHEET AND STRIP FOR ROOFING, EXTERNAL CLADDING AND INTERNAL LINING - PRODUCT SPECIFICATION AND REQUIREMENTS
UNI EN 505 : 2013 ROOFING PRODUCTS FROM METAL SHEET - SPECIFICATION FOR FULLY SUPPORTED ROOFING PRODUCTS OF STEEL SHEET
UNI EN 1317-5 : 2012 ROAD RESTRAINT SYSTEMS - PART 5: PRODUCT REQUIREMENTS AND EVALUATION OF CONFORMITY FOR VEHICLE RESTRAINT SYSTEMS
UNI EN 13964 : 2014 SUSPENDED CEILINGS - REQUIREMENTS AND TEST METHODS
UNI EN 13438 : 2013 PAINTS AND VARNISHES - POWDER ORGANIC COATINGS FOR HOT DIP GALVANISED OR SHERARDIZED STEEL PRODUCTS FOR CONSTRUCTION PURPOSES
UNI EN 1995-1-1 : 2014 EUROCODE 5 - DESIGN OF TIMBER STRUCTURES - PART 1-1: GENERAL - COMMON RULES AND RULES FOR BUILDINGS
17/30357430 DC BS EN 13658-2. Metal lath and beads. Definitions, requirements and test methods. Part 2. External rendering
DIN EN 16475-2:2013-08 (Draft) CHIMNEYS - ACCESSORIES - PART 2: CHIMNEY FANS - REQUIREMENTS AND TEST METHODS
UNI EN ISO 18592 : 2010 RESISTANCE WELDING - DESTRUCTIVE TESTING OF WELDS - METHOD FOR THE FATIGUE TESTING OF MULTI-SPOT-WELDED SPECIMENS
PREN 13914-2 : DRAFT 2013 DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 2: DESIGN CONSIDERATIONS AND ESSENTIAL PRINCIPLES FOR INTERNAL PLASTERING
I.S. EN 1995-1-1:2005 EUROCODE 5: DESIGN OF TIMBER STRUCTURES - PART 1-1: GENERAL - COMMON RULES AND RULES FOR BUILDINGS
DIN EN 16475-2 E : 2017 CHIMNEYS - ACCESSORIES - PART 2: CHIMNEY FANS - REQUIREMENTS AND TEST METHODS
NF EN ISO 14713-2 : 2010 ZINC COATINGS - GUIDELINES AND RECOMMENDATIONS FOR THE PROTECTION AGAINST CORROSION OF IRON AND STEEL IN STRUCTURES - PART 2: HOT DIP GALVANIZING
I.S. EN 13381-5:2014 TEST METHODS FOR DETERMINING THE CONTRIBUTION TO THE FIRE RESISTANCE OF STRUCTURAL MEMBERS - PART 5: APPLIED PROTECTION TO CONCRETE/PROFILED SHEET STEEL COMPOSITE MEMBER
DIN EN 14353:2016-02 (Draft) METAL BEADS AND FEATURE PROFILES FOR USE WITH GYPSUM PLASTERBOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS
PREN 13438 : DRAFT 2012 PAINTS AND VARNISHES - POWDER ORGANIC COATINGS FOR GALVANIZED OR SHERARDIZED STEEL PRODUCTS FOR CONSTRUCTION PURPOSES
DIN EN 10152:2015-10 (Draft) ELECTROLYTICALLY ZINC COATED COLD ROLLED STEEL FLAT PRODUCTS FOR COLD FORMING - TECHNICAL DELIVERY CONDITIONS
14/30266796 DC : 0 BS EN ISO 1514 - PAINTS AND VARNISHES - STANDARD PANELS FOR TESTING
BS EN ISO 14713-1:2017 Zinc coatings. Guidelines and recommendations for the protection against corrosion of iron and steel in structures General principles of design and corrosion resistance
DIN EN ISO 14713-1:2010-05 ZINC COATINGS - GUIDELINES AND RECOMMENDATIONS FOR THE PROTECTION AGAINST CORROSION OF IRON AND STEEL IN STRUCTURES - PART 1: GENERAL PRINCIPLES OF DESIGN AND CORROSION RESISTANCE (ISO 14713-1:2017)
13/30217369 DC : 0 BS EN 13964 - SUSPENDED CEILINGS - REQUIREMENTS AND TEST METHODS
12/30258236 DC : 0 BS EN 10358 - UNALLOYED STEEL PLUMBING FITTINGS - FITTINGS WITH PRESS ENDS FOR UNALLOYED STEEL TUBES
PREN 14566 : DRAFT 2014 MECHANICAL FASTENERS FOR GYPSUM BOARD SYSTEMS - DEFINITIONS, REQUIREMENTS AND TESTS METHODS
DIN EN 14509 E : 2013 SELF-SUPPORTING DOUBLE SKIN METAL FACED INSULATING PANELS - FACTORY MADE PRODUCTS - SPECIFICATIONS
BS ISO 3575:2011 Continuous hot-dip zinc-coated carbon steel sheet of commercial and drawing qualities
17/30357427 DC BS EN 13658-1. Metal lath and beads. Definitions, requirements and test methods. Part 1. Internal plastering
ISO 3575:2016 Continuous hot-dip zinc-coated and zinc-iron alloy-coated carbon steel sheet of commercial and drawing qualities
PREN 845-3 : DRAFT 2012 SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 3: BED JOINT REINFORCEMENT OF STEEL MESHWORK
PREN 845-2 : DRAFT 2012 SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 2: LINTELS
UNE-EN 13611:2016 Safety and control devices for burners and appliances burning gaseous and/or liquid fuels - General requirements
NF EN 16002 : 2010 FLEXIBLE SHEETS FOR WATERPROOFING - DETERMINATION OF THE RESISTANCE TO WIND LOAD OF MECHANICALLY FASTENED FLEXIBLE SHEETS FOR ROOF WATERPROOFING
16/30346712 DC : 0 BS EN 16002 - FLEXIBLE SHEETS FOR WATERPROOFING - DETERMINATION OF THE RESISTANCE TO WIND LOAD OF MECHANICALLY FASTENED FLEXIBLE SHEETS FOR ROOF WATERPROOFING
PREN 14195 : DRAFT 2011 METAL FRAMING COMPONENTS FOR GYPSUM BOARD SYSTEMS - DEFINITIONS, REQUIREMENTS AND TEST METHODS
I.S. EN 13611:2015 SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS
DIN EN 912:2011-09 Timber fasteners - Specifications for connectors for timbers
ISO 14713-2:2009 Zinc coatings Guidelines and recommendations for the protection against corrosion of iron and steel in structures Part 2: Hot dip galvanizing
BS EN 845-1 : 2013 SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 1: WALL TIES, TENSION STRAPS, HANGERS AND BRACKETS
BS EN 508-1:2014 Roofing and cladding products from metal sheet. Specification for self-supporting of steel, aluminium or stainless steel sheet Steel
ISO 14713-1:2017 Zinc coatings — Guidelines and recommendations for the protection against corrosion of iron and steel in structures — Part 1: General principles of design and corrosion resistance
BS EN 10152:2017 Electrolytically zinc coated cold rolled steel flat products for cold forming. Technical delivery conditions
BS EN 13914-1:2016 Design, preparation and application of external rendering and internal plastering External rendering
BS EN 845-3 : 2013 SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 3: BED JOINT REINFORCEMENT OF STEEL ESHWORK
UNE-EN ISO 1514:2017 Paints and varnishes - Standard panels for testing (ISO 1514:2016)
UNE-EN 14195:2015 Metal framing components for gypsum board systems - Definitions, requirements and test methods
UNE-EN 1995-1-1:2016 Eurocode 5: Design of timber structures - Part 1-1: General - Common rules and rules for buildings.
UNE-EN 10152:2017 Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions
BS EN 14783:2013 Fully supported metal sheet and strip for roofing, external cladding and internal lining. Product specification and requirements
DIN EN 14783:2013-07 FULLY SUPPORTED METAL SHEET AND STRIP FOR ROOFING, EXTERNAL CLADDING AND INTERNAL LINING - PRODUCT SPECIFICATION AND REQUIREMENTS
BS EN 1075:2014 Timber structures. Test methods. Joints made with punched metal plate fasteners
BS EN 13438:2013 Paints and varnishes. Powder organic coatings for hot dip galvanised or sherardised steel products for construction purposes
UNE-EN 1075:2015 Timber structures - Test methods - Joints made with punched metal plate fasteners
ISO 18592:2009 Resistance welding Destructive testing of welds Method for the fatigue testing of multi-spot-welded specimens
UNE-EN 10169:2011 Continuously organic coated (coil coated) steel flat products - Technical delivery conditions
BS EN 1317-5 : 2007 ROAD RESTRAINT SYSTEMS - PART 5: PRODUCT REQUIREMENTS AND EVALUATION OF CONFORMITY FOR VEHICLE RESTRAINT SYSTEMS
EN 845-3:2013+A1:2016 SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 3: BED JOINT REINFORCEMENT OF STEEL MESHWORK
EN 845-2:2013+A1:2016 SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 2: LINTELS
EN ISO 18592:2009 Resistance welding - Destructive testing of welds - Method for the fatigue testing of multi-spot-welded specimens (ISO 18592:2009)
EN 845-1:2013+A1:2016 Specification for ancillary components for masonry - Part 1: Wall ties, tension straps, hangers and brackets
EN 14509:2013 Self-supporting double skin metal faced insulating panels - Factory made products - Specifications
EN 505:2013 Roofing products from metal sheet - Specification for fully supported roofing products of steel sheet
EN ISO 14713-1:2017 Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 1: General principles of design and corrosion resistance (ISO 14713-1:2017)
EN ISO 1514:2016 Paints and varnishes - Standard panels for testing (ISO 1514:2016)
EN 14353:2017 Metal beads and feature profiles for use with gypsum plasterboards - Definitions, requirements and test methods
EN 16475-2:2017 Chimneys - Accessories - Part 2: Chimney fans - Requirements and test methods
EN 14195:2014 Metal framing components for gypsum board systems - Definitions, requirements and test methods
EN 912:2011 Timber fasteners - Specifications for connectors for timbers
EN 14783:2013 Fully supported metal sheet and strip for roofing, external cladding and internal lining - Product specification and requirements
EN 13914-2:2016 Design, preparation and application of external rendering and internal plastering - Part 2: Internal plastering
09/30207859 DC : 0 BS EN 16002 - FLEXIBLE SHEETS FOR WATERPROOFING - DETERMINATION OF THE RESISTANCE TO WIND LOAD OF MECHANICALLY FASTENED FLEXIBLE SHEETS FOR ROOF WATERPROOFING
PD CEN/TR 16239:2011 Installation rules of fibrous (gypsum) plaster works
I.S. EN 16475-3:2016 CHIMNEYS - ACCESSORIES - PART 3: DRAUGHT REGULATORS, STANDSTILL OPENING DEVICES AND COMBINED SECONDARY AIR DEVICES - REQUIREMENTS AND TEST METHODS
12/30238456 DC : 0 BS EN 13438 - PAINTS AND VARNISHES - POWDER ORGANIC COATINGS FOR GALVANIZED OR SHERARDIZED STEEL PRODUCTS FOR CONSTRUCTION PURPOSES
BS EN 16475-2:2017 Chimneys. Accessories Chimney fans. Requirements and test methods
PREN 15773 : DRAFT 2016 INDUSTRIAL APPLICATION OF POWDER ORGANIC COATINGS TO HOT DIP GALVANIZED OR SHERARDIZED STEEL ARTICLES [DUPLEX SYSTEMS] - SPECIFICATIONS, RECOMMENDATIONS AND GUIDELINES
16/30332914 DC : 0 BS EN 14353 - METAL BEADS AND FEATURE PROFILES FOR USE WITH GYPSUM PLASTERBOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS
15/30312507 DC : 0 BS ISO 3575 - CONTINUOUS HOT-DIP ZINC-COATED AND ZINC-IRON ALLOY-COATED CARBON STEEL SHEET OF COMMERCIAL AND DRAWING QUALITIES
17/30360051 DC : 0 BS EN 13611 - SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS
BS EN 13381-5:2014 Test methods for determining the contribution to the fire resistance of structural members Applied protection to concrete/profiled sheet steel composite member
BS EN 13611:2015 Safety and control devices for burners and appliances burning gaseous and/or liquid fuels. General requirements
I.S. EN ISO 14713-1:2017 ZINC COATINGS - GUIDELINES AND RECOMMENDATIONS FOR THE PROTECTION AGAINST CORROSION OF IRON AND STEEL IN STRUCTURES - PART 1: GENERAL PRINCIPLES OF DESIGN AND CORROSION RESISTANCE (ISO 14713-1:2017)
DIN EN ISO 14713-1 E : 2010 ZINC COATINGS - GUIDELINES AND RECOMMENDATIONS FOR THE PROTECTION AGAINST CORROSION OF IRON AND STEEL IN STRUCTURES - PART 1: GENERAL PRINCIPLES OF DESIGN AND CORROSION RESISTANCE (ISO 14713-1:2017)
UNE-EN ISO 14713-1:2017 Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 1: General principles of design and corrosion resistance (ISO 14713-1:2017)
BS EN 16002:2010 Flexible sheets for waterproofing. Determination of the resistance to wind load of mechanically fastened flexible sheets for roof waterproofing
BS ISO 4998:2014 Continuous hot-dip zinc-coated and zinc-iron alloy-coated carbon steel sheet of structural quality
PREN 13964 : DRAFT 2013 SUSPENDED CEILINGS - REQUIREMENTS AND TEST METHODS
UNE-EN ISO 18592:2010 Resistance welding - Destructive testing of welds - Method for the fatigue testing of multi-spot-welded specimens (ISO 18592:2009)
I.S. EN 1090-2:2008 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
EN 16475-3:2016 Chimneys - Accessories - Part 3: Draught regulators, standstill opening devices and combined secondary air devices - Requirements and test methods
UNI EN 10169 : 2012 CONTINUOUSLY ORGANIC COATED (COIL COATED) STEEL FLAT PRODUCTS - TECHNICAL DELIVERY CONDITIONS
DIN EN 13611:2016-09 SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS
PREN 13611 : DRAFT 2017 SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS
EN 13611:2015/AC:2016 SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS
I.S. EN ISO 18592:2009 RESISTANCE WELDING - DESTRUCTIVE TESTING OF WELDS - METHOD FOR THE FATIGUE TESTING OF MULTI-SPOT-WELDED SPECIMENS
DIN EN 1995-1-1 E : 2010 EUROCODE 5: DESIGN OF TIMBER STRUCTURES - PART 1-1: GENERAL - COMMON RULES AND RULES FOR BUILDINGS
UNE-EN 13964:2016 Suspended ceilings - Requirements and test methods
UNE-EN 912:2011 Timber fasteners - Specifications for connectors for timbers
UNE-EN 508-1:2014 Roofing and cladding products from metal sheet - Specification for self-supporting of steel, aluminium or stainless steel sheet - Part 1: Steel
UNE-EN 12574-2:2017 Stationary waste containers - Part 2: Performance requirements and test methods
BS EN 13964:2014 Suspended ceilings. Requirements and test methods
ISO 1514:2016 Paints and varnishes — Standard panels for testing
DIN EN 16002:2010-10 FLEXIBLE SHEETS FOR WATERPROOFING - DETERMINATION OF THE RESISTANCE TO WIND LOAD OF MECHANICALLY FASTENED FLEXIBLE SHEETS FOR ROOF WATERPROOFING
DIN EN ISO 14713-2:2010-05 ZINC COATINGS - GUIDELINES AND RECOMMENDATIONS FOR THE PROTECTION AGAINST CORROSION OF IRON AND STEEL IN STRUCTURES - PART 2: HOT DIP GALVANIZING
EN 1317-5:2007+A2:2012/AC:2012 ROAD RESTRAINT SYSTEMS - PART 5: PRODUCT REQUIREMENTS AND EVALUATION OF CONFORMITY FOR VEHICLE RESTRAINT SYSTEMS
I.S. EN 13611:2015/AC:2016 SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS
DIN EN 14353:2017-09 METAL BEADS AND FEATURE PROFILES FOR USE WITH GYPSUM PLASTERBOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS

ISO 10275:2007 Metallic materials Sheet and strip Determination of tensile strain hardening exponent
EN 10079:2007 Definition of steel products
EN 10027-2:2015 DESIGNATION SYSTEMS FOR STEELS - PART 2: NUMERICAL SYSTEM
EN 10152:2017 Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions
EN ISO 6892-1:2016 Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016)
ISO 14713-1:2017 Zinc coatings — Guidelines and recommendations for the protection against corrosion of iron and steel in structures — Part 1: General principles of design and corrosion resistance
ISO 6892-1:2016 Metallic materials Tensile testing Part 1: Method of test at room temperature
EN 10149-2:2013 Hot rolled flat products made of high yield strength steels for cold forming - Part 2: Technical delivery conditions for thermomechanically rolled steels
EN 10169:2010+A1:2012 Continuously organic coated (coil coated) steel flat products - Technical delivery conditions
EN 10143:2006 (edition 2) Continuously hot-dip coated steel sheet and strip - Tolerances on dimensions and shape
EN 10021:2006 General technical delivery conditions for steel products
EN ISO 14713-1:2017 Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 1: General principles of design and corrosion resistance (ISO 14713-1:2017)
EN 10204:2004 Metallic products - Types of inspection documents
EN 10049:2013 Measurement of roughness average Ra and peak count RPc on metallic flat products
EN 10027-1:2016 Designation systems for steels - Part 1: Steel names
ISO 10113:2006 Metallic materials Sheet and strip Determination of plastic strain ratio
EN 10020:2000 Definition and classification of grades of steel
EN 606:2004 BAR CODING - TRANSPORT AND HANDLING LABELS FOR STEEL PRODUCTS
ISO 14713-2:2009 Zinc coatings Guidelines and recommendations for the protection against corrosion of iron and steel in structures Part 2: Hot dip galvanizing
EN 10325:2006 Steel - Determination of yield strength increase by the effect of heat treatment [Bake-Hardening-Index]
EN ISO 14713-2:2009 Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 2: Hot dip galvanizing (ISO 14713-2:2009)

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.