• There are no items in your cart

EN 12158-2:2000+A1:2010

Current
Current

The latest, up-to-date edition.

Builders' hoists for goods - Part 2: Inclined hoists with non-accessible load carrying devices
Published date

07-21-2010

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of hazards
5 Safety requirements and/or measures
6 Verification
7 User Information
Annex A (normative) - European stormwind map
Annex B (informative) - Electric safety devices
Annex ZA (informative) - Relationship between this
         European Standard and the Essential
         Requirements of EU Directive 2006/42/EC
Bibliography

1.1This standard deals with power operated temporarily installed builders hoists intended for use by persons who are permitted to enter sites of engineering and construction, serving either one upper landing or a work area extending to the end of the guides, (e.g. a roof) having a load carrying device (lcd):-which is intended for the transportation of goods only;-where it is forbidden for persons to step upon it at any time;-which is guided;-which is designed to travel at an angle of at least 30 degrees to the vertical but may be used at any angle between the vertical and the maximum inclination as specified by the manufacturer;-which is sustained by steel wire rope and a positive drive system;-which is controlled by hold-to-run controls by the operator;-which does not benefit from the use of any counterweight;-which has a maximum rated load of 300 kg;-which has a maximum speed of 1,00 m/s;and where the guides require support from separate structures.1.2The standard identifies hazards as listed in clause 4, which arise during the various phases in the life of such equipment and describes methods for the elimination or reduction of these hazards when used as intended by the manufacturer.1.3This European standard does not specify the additional requirements for:-operation in severe conditions (e.g. extreme climates, strong magnetic fields);-lightning protection;-operation subject to special rules (e.g. potentially explosive atmospheres);-electromagnetic compatibility (emission, immunity);-handling of loads the nature of which could lead to dangerous situations (e.g. molten metal, acids/bases, radiating materials, fragile loads);-the use of combustion engines;-the use of remote controls;-hazards occurring during manufacture;-hazards occurring as a result of mobility;-hazards occurring as a result of being erected over a public road;-earthquakes;-noise.(...)

Committee
CEN/TC 10
DevelopmentNote
2000 Edition Re-issued in July 2010 & incorporates AMD 1 2010. (08/2010)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current

BS EN 81-43:2009 Safety rules for the construction and installation of lifts. Special lifts for the transport of persons and goods Lifts for cranes
04/102158 DC : 0 BS EN 81-43 - SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - SPECIAL LIFTS FOR THE TRANSPORT OF PERSONS AND GOODS - PART 43: SPECIAL PURPOSE LIFTS FOR CRANES
DIN EN 81-43:2010-05 Safety rules for the construction and installation of lifts - Special lifts for the transport of persons and goods - Part 43: Lifts for cranes
PD ISO/TR 12603:2010 Building construction machinery and equipment. Classification
ISO/TR 12603:2010 Building construction machinery and equipment Classification
DIN EN 12158-1:2011-06 Builders' hoists for goods - Part 1: Hoists with accessible platforms (includes Amendment A1:2010)
UNE-EN 12159:2013 Builders hoists for persons and materials with vertically guided cages
BS EN 12159:2012 Builders hoists for persons and materials with vertically guided cages
UNI EN 12158-1 : 2010 BUILDERS' HOISTS FOR GOODS - PART 1: HOISTS WITH ACCESSIBLE PLATFORMS
NF EN 12158-1 : 2000 + A1 2010 BUILDERS' HOISTS FOR GOODS - PART 1: HOISTS WITH ACCESSIBLE PLATFORMS
UNI EN 81-43 : 2009 SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - SPECIAL LIFTS FOR THE TRANSPORT OF PERSONS AND GOODS - PART 43: LIFTS FOR CRANES
DIN EN 12159:2013-03 BUILDERS HOISTS FOR PERSONS AND MATERIALS WITH VERTICALLY GUIDED CAGES
I.S. EN 12158-1:2000 BUILDERS' HOISTS FOR GOODS - PART 1: HOISTS WITH ACCESSIBLE PLATFORMS
I.S. EN 12159:2012 BUILDERS HOISTS FOR PERSONS AND MATERIALS WITH VERTICALLY GUIDED CAGES
11/30215034 DC : DRAFT MAR 2011 BS EN 12159 - BUILDERS HOISTS FOR PERSONS AND MATERIALS WITH VERTICALLY GUIDED CAGES
I.S. EN 16719:2018 TRANSPORT PLATFORMS
UNI EN 12159 : 2013 BUILDERS HOISTS FOR PERSONS AND MATERIALS WITH VERTICALLY GUIDED CAGES
08/30181434 DC : DRAFT DEC 2008 BS EN 12159 AMD1 - BUILDERS HOISTS FOR PERSONS AND MATERIALS WITH VERTICALLY GUIDED CAGES
UNE-EN 12158-1:2001 Builders hoists for goods. Part 1: Hoists with accessible platforms.
EN 81-43:2009 Safety rules for the construction and installation of lifts - Special lifts for the transport of persons and goods - Part 43: Lifts for cranes
EN 12159:2012 Builders hoists for persons and materials with vertically guided cages
I.S. EN 81-43:2009 SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - SPECIAL LIFTS FOR THE TRANSPORT OF PERSONS AND GOODS - PART 43: LIFTS FOR CRANES
EN 16719:2018 Transport platforms
BS EN 12158-1 : 2000 BUILDERS' HOISTS FOR GOODS - PART 1: HOISTS WITH ACCESSIBLE PLATFORMS
EN 12158-1:2000+A1:2010 Builders' hoists for goods - Part 1: Hoists with accessible platforms

ISO 2408:2017 Steel wire ropes — Requirements
EN 982:1996+A1:2008 Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics
ISO 4871:1996 Acoustics — Declaration and verification of noise emission values of machinery and equipment
ISO 4302:2016 Cranes Wind load assessment
EN 1088:1995+A2:2008 Safety of machinery - Interlocking devices associated with guards - Principles for design and selection
IEC 60947-4-1:2009+AMD1:2012 CSV Low-voltage switchgear and controlgear - Part 4-1: Contactors and motor-starters - Electromechanical contactors and motor-starters
ISO 6336-2:2006 Calculation of load capacity of spur and helical gears Part 2: Calculation of surface durability (pitting)
EN 349:1993+A1:2008 Safety of machinery - Minimum gaps to avoid crushing of parts of the human body
EN ISO 13850:2015 Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015)
IEC 60947-5-1 : 4.0 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-1: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - ELECTROMECHANICAL CONTROL CIRCUIT DEVICES
ISO 6336-3:2006 Calculation of load capacity of spur and helical gears Part 3: Calculation of tooth bending strength
IEC 60204-32:2008 Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines
EN ISO 13857:2008 Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)
ISO 6336-5:2016 Calculation of load capacity of spur and helical gears Part 5: Strength and quality of materials
HD 22-1 : 200S4 CABLES OF RATED VOLTAGES UP TO AND INCLUDING 450/750 V AND HAVING THERMOSETTING INSULATION - GENERAL REQUIREMENTS
EN 60204-32:2008 Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines
EN ISO 12100-1:2003/A1:2009 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY
ISO 4309:2010 Cranes Wire ropes Care and maintenance, inspection and discard
EN 60947-4-1 : 2010 AMD 1 2012 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-1: CONTACTORS AND MOTOR-STARTERS - ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS (IEC 60947-4-1:2009/A1:2012)
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
ISO 12100-2:2003 Safety of machinery Basic concepts, general principles for design Part 2: Technical principles
ISO 13857:2008 Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs
EN ISO 12100-2:2003/A1:2009 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES
ISO 6336-1:2006 Calculation of load capacity of spur and helical gears Part 1: Basic principles, introduction and general influence factors
ISO 12100-1:2003 Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology
ISO 13850:2015 Safety of machinery Emergency stop function Principles for design
EN ISO 4871:2009 Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.