• There are no items in your cart

EN 12201-2:2011+A1:2013

Withdrawn
Withdrawn

A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes
Withdrawn date

03-31-2014

Published date

09-25-2013

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviations
4 Material
5 General characteristics
6 Geometrical characteristics
7 Mechanical characteristics
8 Physical characteristics
9 Chemical characteristics of pipes in contact with
   chemicals
10 Performance requirements
11 Marking
Annex A (informative) - Relationship between PN, MRS, S
        and SDR
Annex B (normative) - Pipes with co-extruded layers
Annex C (normative) - Pipes with peelable layer
Annex D (normative) - Pipe stiffness for vacuum sewer
        systems
Bibliography

This part of EN 12201 specifies the characteristics of pipes made from polyethylene (PE 100, PE 80 and PE 40) for buried and above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drainage and sewerage under pressure, vacuum sewer systems, and water for other purposes.NOTE 1For PE components intended for the conveyance of water for human consumption and raw water prior to treatment attention is drawn to 5.3 of this European Standard. Components manufactured for water for general purposes, drainage and sewerage may not be suitable for water supply for human consumption.It also specifies the test parameters for the test methods referred to in this standard.In conjunction with Part 1 and Parts 3 to 5 of EN 12201, it is applicable to PE pipes, their joints and to joints with components of PE and other materials intended to be used under the following conditions:a)allowable operating pressure, PFA, up to 25 bar );b)an operating temperature of 20 °C as a reference temperature;c)buried in the ground;d)sea outfalls;e)laid in water;f)above ground, including pipes suspended below bridges. NOTE 2For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see Annex A of EN 12201-1:2011.NOTE 3Pipes constructions including barrier layers are not covered by this document. EN 12201 covers a range of allowable operating pressures and gives requirements concerning colours and additives.It covers three types of pipe:-PE pipes (outside diameter dn) including any identification stripes;-PE pipes with co-extruded layers on either or both the outside and/or inside of the pipe (total outside diameter dn) as specified in Annex B, where all layers have the same MRS rating;-PE pipes (outside diameter dn) with a peelable, contiguous thermoplastics additional layer on the outside of the pipe (‘coated pipe’) as specified in Annex C.NOTE 4It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes.NOTE 5Assessment of the resistance to slow crack growth of the PE pipe compound used for the manufacture of products to this document is required in accordance with Table 2 of EN 12201-1:2011.

Committee
CEN/TC 155
DevelopmentNote
Supersedes EN 13244-2 & PREN 12201-2. (09/2011) 2011 Edition Re-Issued in September 2013 & incorporates AMD 1 2013. (10/2013)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Withdrawn
Supersedes

I.S. EN 14409-3:2004 PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND WATER SUPPLY NETWORKS - PART 3: LINING WITH CLOSE FIT-PIPES
UNI EN 15014 : 2008 PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND SYSTEMS FOR WATER AND OTHER FLUIDS UNDER PRESSURE - PERFORMANCE CHARACTERISTICS FOR PIPES, FITTINGS AND THEIR JOINTS
11/30239906 DC : 0 BS EN 15014 - PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND PIPING COMPONENTS FOR WATER AND OTHER LIQUIDS UNDER PRESSURE - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS
17/30341312 DC : 0 BS EN ISO 21225-1 - PLASTICS PIPING SYSTEMS FOR THE TRENCHLESS REPLACEMENT OF UNDERGROUND PIPELINE NETWORKS - PART 1: REPLACEMENT ON THE LINE BY PIPE BURSTING AND PIPE EXTRACTION
S.R. CEN/TS 12201-7:2014 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY
I.S. EN ISO 11297-2:2018 PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND DRAINAGE AND SEWERAGE NETWORKS UNDER PRESSURE - PART 2: LINING WITH CONTINUOUS PIPES (ISO 11297-2:2018)
DIN EN 12201-5:2011-11 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system
DIN EN 12201-1:2011-11 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General
BS EN 14525:2004 Ductile iron wide tolerance couplings and flange adaptors for use with pipes of different materials: ductile iron, grey iron, steel, PVC-U, PE, fibre-cement
BS EN 12201-4:2012 Plastics piping systems for water supply, and for drainage and sewerage under pressure. Polyethylene (PE) Valves
EN 12201-1:2011 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General
EN 12201-5:2011 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system
EN 12201-4:2012 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 4: Valves
17/30341315 DC : 0 BS EN ISO 21225-2 - PLASTICS PIPING SYSTEMS FOR THE TRENCHLESS REPLACEMENT OF UNDERGROUND PIPELINE NETWORKS - PART 2: REPLACEMENT OFF THE LINE BY HORIZONTAL DIRECTIONAL DRILLING AND IMPACT MOLING
10/30216654 DC : 0 BS EN 12842 - DUCTILE IRON FITTINGS FOR PVC-U OR PE PIPING SYSTEMS - REQUIREMENTS AND TEST METHODS
PREN 15014 : DRAFT 2014 PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND PIPING COMPONENTS FOR WATER UNDER PRESSURE - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS
DD CEN/TS 12201-7:2003 Plastics piping systems for water supply. Polyethylene (PE) Guidance for the assessment of conformity
I.S. EN ISO 11297-3:2013 PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND DRAINAGE AND SEWERAGE NETWORKS UNDER PRESSURE - PART 3: LINING WITH CLOSE-FIT PIPES (ISO 11297-3:2013)
EN ISO 11297-2:2018 Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 2: Lining with continuous pipes (ISO 11297-2:2018)
DIN EN 1366-3:2009-07 Fire resistance tests for service installations - Part 3: Penetration seals
DIN EN 12842:2012-11 Ductile iron fittings for PVC-U or PE piping systems - Requirements and test methods
UNE-EN 12201-5:2012 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system
I.S. EN 12201-4:2012 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 4: VALVES FOR WATER SUPPLY SYSTEMS
I.S. EN 12842:2012 DUCTILE IRON FITTINGS FOR PVC-U OR PE PIPING SYSTEMS - REQUIREMENTS AND TEST METHODS
I.S. EN 12201-5:2011 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 5: FITNESS FOR PURPOSE OF THE SYSTEM
I.S. EN 12201-3:2011 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 3: FITTINGS
DIN EN 14409-3:2004-12 PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND WATER SUPPLY NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES
I.S. EN 12201-1:2011 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 1: GENERAL
I.S. EN 14125:2013 THERMOPLASTIC AND FLEXIBLE METAL PIPEWORK FOR UNDERGROUND INSTALLATION AT PETROL FILLING STATIONS
I.S. EN 1366-3:2009 FIRE RESISTANCE TESTS FOR SERVICE INSTALLATIONS - PART 3: PENETRATION SEALS
ISO 11298-2:2018 Plastics piping systems for renovation of underground water supply networks — Part 2: Lining with continuous pipes
11/30231856 DC : 0 BS EN 14125 - THERMOPLASTIC AND FLEXIBLE METAL PIPEWORK FOR UNDERGROUND INSTALLATION AT PETROL FILLING STATIONS
12/30258383 DC : 0 BS EN ISO 11297-3 - PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND DRAINAGE AND SEWERAGE NETWORKS UNDER PRESSURE - PART 3: LINING WITH CLOSE-FIT PIPES
07/19990369 DC : 0 BS EN 806-4 - SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 4 - INSTALLATION
PD CEN/TS 12201-7:2014 Plastics piping systems for water supply, and for drainage and sewerage under pressure. Polyethylene (PE) Guidance for the assessment of conformity
EN ISO 11297-3:2013 PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND DRAINAGE AND SEWERAGE NETWORKS UNDER PRESSURE - PART 3: LINING WITH CLOSE-FIT PIPES (ISO 11297-3:2013)
EN ISO 11298-2:2018 Plastics piping systems for renovation of underground water supply networks - Part 2: Lining with continuous pipes (ISO 11298-2:2018)
DIN EN 14525 E : 2005 DUCTILE IRON WIDE TOLERANCE COULINGS AND FLANGE ADAPTORS FOR USE WITH PIPES OF DIFFERENT MATERIALS: DUCTILE IRON, GREY IRON, STEEL, PVC-U, PE, FIBRE-CEMENT
BS EN 14409-3:2004 Plastics piping systems for renovation of underground water supply networks Lining with close fit pipes
BS EN 12201-3 : 2011 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 3: FITTINGS
BS EN 12201-1:2011 Plastics piping systems for water supply, and for drainage and sewerage under pressure. Polyethylene (PE) General
UNE-EN 12842:2013 Ductile iron fittings for PVC-U or PE piping systems - Requirements and test methods
UNI EN 14525 : 2005 DUCTILE IRON WIDE TOLERANCE COUPLINGS AND FLANGE ADAPTORS FOR USE WITH PIPES OF DIFFERENT MATERIALS: DUCTILE IRON, GREY IRON, STEEL, PVC-U PE, FIBRE-CEMENT
UNI EN 12201-1 : 2012 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 1: GENERAL
UNI EN 12842 : 2012 DUCTILE IRON FITTINGS FOR PVC-U OR PE PIPING SYSTEMS - REQUIREMENTS AND TEST METHODS
UNI EN 12201-3 : 2013 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 3: FITTINGS
I.S. EN 14525:2005 DUCTILE IRON WIDE TOLERANCE COUPLINGS AND FLANGE ADAPTORS FOR USE WITH PIPES OF DIFFERENT MATERIALS: DUCTILE IRON, GREY IRON, STEEL, PVC-U PE, FIBRE-CEMENT
UNI EN 14125 : 2013 THERMOPLASTIC AND FLEXIBLE METAL PIPEWORK FOR UNDERGROUND INSTALLATION AT PETROL FILLING STATIONS
ONORM EN 1366-3 : 2009 FIRE RESISTANCE TESTS FOR SERVICE INSTALLATIONS - PART 3: PENETRATION SEALS
UNI EN 12201-4 : 2012 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 4: VALVES FOR WATER SUPPLY SYSTEMS
UNI EN 12201-5 : 2012 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 5: FITNESS FOR PURPOSE OF THE SYSTEM
DIN EN ISO 11297-3 E : 2013 PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND DRAINAGE AND SEWERAGE NETWORKS UNDER PRESSURE - PART 3: LINING WITH CLOSE-FIT PIPES (ISO 11297-3:2013)
UNI CEN/TS 12201-7 : 2014 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY
PREN 12842 : DRAFT 2010 DUCTILE IRON FITTINGS FOR PVC-U OR PE PIPING SYSTEMS - REQUIREMENTS AND TEST METHODS
PREN 14125 : DRAFT 2011 THERMOPLASTIC AND FLEXIBLE METAL PIPEWORK FOR UNDERGROUND INSTALLATION AT PETROL FILLING STATIONS
UNI EN ISO 11297-3 : 2013 PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND DRAINAGE AND SEWERAGE NETWORKS UNDER PRESSURE - PART 3: LINING WITH CLOSE-FIT PIPES
BS EN ISO 11297-3:2013 Plastics piping systems for renovation of underground drainage and sewerage networks under pressure Lining with close-fit pipes
I.S. CEN TS 12201-7:2003 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY - POLYETHYLENE (PE) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY
DIN EN 12201-3:2013-01 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 3: FITTINGS
UNE-EN 12201-4:2012 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 4: Valves
BS EN 1366-3:2009 Fire resistance tests for service installations Penetration seals
UNE-EN 1366-3:2011 Fire resistance tests for service installations - Part 3: Penetration seals
UNE-EN 14125:2013 Thermoplastic and flexible metal pipework for underground installation at petrol filling stations
BS EN 806-2:2005 Specifications for installations inside buildings conveying water for human consumption Design
BS EN 14125:2013 Thermoplastic and flexible metal pipework for underground installation at petrol filling stations
BS EN 12201-5:2011 Plastics piping systems for water supply, and for drainage and sewerage under pressure. Polyethylene (PE) Fitness for purpose of the system
EN 14409-3:2004 Plastics piping systems for renovation of underground water supply networks - Part 3: Lining with close fit-pipes
UNI EN 1366-3 : 2009 FIRE RESISTANCE TESTS FOR SERVICE INSTALLATIONS - PART 3: PENETRATION SEALS
EN 806-2:2005 Specification for installations inside buildings conveying water for human consumption - Part 2: Design
EN 14525:2004 Ductile iron wide tolerance couplings and flange adaptors for use with pipes of different materials: ductile iron, Grey iron, Steel, PVC-U PE, Fibre-cement
EN 14125:2013 Thermoplastic and flexible metal pipework for underground installation at petrol filling stations
EN 12842:2012 Ductile iron fittings for PVC-U or PE piping systems - Requirements and test methods
17/30361344 DC : 0 BS EN ISO 11298-3 - PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND WATER SUPPLY NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES
ISO 11297-2:2018 Plastics piping systems for renovation of underground drainage and sewerage networks under pressure — Part 2: Lining with continuous pipes
I.S. EN ISO 11298-2:2018 PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND WATER SUPPLY NETWORKS - PART 2: LINING WITH CONTINUOUS PIPES (ISO 11298-2:2018)
07/30150249 DC : 0 BS EN ISO 23936-1 - PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - NON-METALLIC MATERIALS IN CONTACT WITH MEDIA RELATED TO OIL AND GAS PRODUCTION - PART 1: THERMOPLASTICS
ISO 21225-1:2018 Plastics piping systems for the trenchless replacement of underground pipeline networks — Part 1: Replacement on the line by pipe bursting and pipe extraction
UNI EN 806-2 : 2008 SPECIFICATION FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 2: DESIGN
14/30297465 DC : 0 BS EN 15014 - PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND PIPING COMPONENTS FOR WATER UNDER PRESSURE - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS
UNE-EN ISO 11297-3:2014 Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 3: Lining with close-fit pipes (ISO 11297-3:2013)
DIN EN ISO 11297-3:2013-11 PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND DRAINAGE AND SEWERAGE NETWORKS UNDER PRESSURE - PART 3: LINING WITH CLOSE-FIT PIPES (ISO 11297-3:2013)
NORSOK M 630 : REV 6 MATERIAL DATA SHEETS AND ELEMENT DATA SHEETS FOR PIPING
DIN EN 12201-4:2012-04 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 4: Valves
DIN EN 806-2:2005-06 Specification for installations inside buildings conveying water for human consumption - Part 2: Design
DIN EN 14125:2013-09 THERMOPLASTIC AND FLEXIBLE METAL PIPEWORK FOR UNDERGROUND INSTALLATION AT PETROL FILLING STATIONS
UNE-EN 12201-1:2012 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General
BS EN 12842:2012 Ductile iron fittings for PVC-U or PE piping systems. Requirements and test methods
EN 1366-3:2009 Fire resistance tests for service installations - Part 3: Penetration seals
DIN EN 14525:2005-02 Ductile iron wide tolerance couplings and flange adaptors for use with pipes of different materials: Ductile iron, grey iron, steel, PVC-U, PE, fibre-cement
CEN/TS 12201-7:2014 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity
EN 12201-3:2011+A1:2012 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 3: Fittings
UNE-EN 12201-3:2012 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 3: Fittings

EN ISO 3126:2005 Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005)
ISO/TR 10358:1993 Plastics pipes and fittings Combined chemical-resistance classification table
ISO 1167-2:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces
EN 12201-3:2011+A1:2012 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 3: Fittings
89/106/EEC : 1988 COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS
EN ISO 1167-2:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces (ISO 1167-2:2006)
EN ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006)
ISO 13968:2008 Plastics piping and ducting systems — Thermoplastics pipes — Determination of ring flexibility
EN ISO 178:2010/A1:2013 PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010/AMD 1:2013)
ISO 4433-1:1997 Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 1: Immersion test method
EN ISO 6259-1:2015 Thermoplastics pipes - Determination of tensile properties - Part 1: General test method (ISO 6259-1:2015)
CEN/TR 15438:2007 Plastics piping systems - Guidance for coding of products and their intended uses
ISO 6259-1:2015 Thermoplastics pipes Determination of tensile properties Part 1: General test method
ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
ISO 11922-1:1997 Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series
EN 12201-5:2011 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system
ISO 4433-2:1997 Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 2: Polyolefin pipes
ISO 21004:2006 Plastics piping systems Multilayer pipes and their joints, based on thermoplastics, for water supply
EN ISO 13968:2008 Plastics piping and ducting systems - Thermoplastics pipes - Determination of ring flexibility (ISO 13968:2008)
EN ISO 9969:2016 Thermoplastics pipes - Determination of ring stiffness (ISO 9969:2016)
ISO 11357-6:2008 Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
ISO 4065:1996 Thermoplastics pipes Universal wall thickness table
ISO 6259-3:2015 Thermoplastics pipes Determination of tensile properties Part 3: Polyolefin pipes
EN ISO 2505:2005 Thermoplastics pipes - Longitudinal reversion - Test method and parameters (ISO 2505:2005)
EN ISO 1133:2005 PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND THE MELT VOLUME-FLOW RATE (MVR) OF THE THERMOPLASTICS
EN 12201-1:2011 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General
ISO 178:2010 Plastics Determination of flexural properties
ISO 9969:2016 Thermoplastics pipes Determination of ring stiffness
ISO 1133:2005 Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
CEN/TS 12201-7:2014 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity
ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
ISO 2505:2005 Thermoplastics pipes — Longitudinal reversion — Test method and parameters

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.