EN 12206-1:2004
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
05-19-2021
07-07-2004
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Test methods
Annex A (normative) Methods for the determination of the
mass per unit area of conversion layers and for
the identification of chromium, phosphorus and zinc
Annex B (normative) Requirements for alternative pretreatment
Annex C (normative) Measurement of film thickness
Annex D (normative) Falling weight test apparatus
Annex E (informative) Sequence of pretreatment stages
Annex F (normative) Enhanced durability coating powders
Bibliography
This Part of EN 12206 specifies requirements and the corresponding methods of test relating to the organic coating of aluminium and aluminium alloy extrusions, sheet and preformed sections for architectural purposes, using exclusively coating powders. It also describes :a) the pretreatment of the substrate prior to the coating process ;b) the coating powder ;c) the coating process ;d) the final product.Each item is dealt with separately in this Part of EN 12206 so that any interested party can ensure compliance appropriate to its area of responsibility.CAUTION : The procedures describes in this standard are intended to be carried out by suitably trained and/or supervised personnel. The substances and procedures used in this method may be injurious to health if adequate precautions are not taken. Attention is drawn in the text to specific hazards. This standard refers only to its technical suitability and does not absolve the user from statutory obligations relating to health and safety.
| Committee |
CEN/TC 139
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| DIN EN 12206-1:2004-09 | Identical |
| NEN-EN 12206-1:2019 Ontw | Identical |
| SN EN 12206-1 : 2004 | Identical |
| NS EN 12206-1 : 1ED 2004 | Identical |
| NF EN 12206-1 : 2011 | Identical |
| I.S. EN 12206-1:2004 | Identical |
| BS EN 12206-1:2004 | Identical |
| NBN EN 12206-1 : 2004 | Identical |
| PN EN 12206-1 : NOV 2005 | Identical |
| UNE-EN 12206-1:2005 | Identical |
| NEN EN 12206-1 : 2004 | Identical |
| UNI EN 12206-1 : 2005 | Identical |
| ONORM EN 12206-1 : 2004 | Identical |
| UNI EN 1090-3 : 2008 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES |
| ONORM EN 1090-3 : 2008 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES |
| DIN EN 1090-3:2008-09 | EXECUTION OF STEEL AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL RULES FOR EXECUTION OF ALUMINIUM STRUCTURES |
| BS IEC 60092-306:2009 | Electrical installations in ships Equipment. Luminaires and lighting accessories |
| PREN 1090-3 : DRAFT 2017 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES |
| ISO/TS 16688:2017 | Guidelines for the selection of coating types, tests and methods of assessing the performance of coated aluminium in architectural applications |
| UNE-IEC 60092-306:2010 | Electrical installations in ships - Part 306: Equipment - Luminaires and lighting accessories |
| I.S. EN 12020-1:2008 | ALUMINIUM AND ALUMINIUM ALLOYS - EXTRUDED PRECISION PROFILES IN ALLOYS EN AW-6060 AND EN AW-6063 - PART 1: TECHNICAL CONDITIONS FOR INSPECTION AND DELIVERY |
| PD ISO/TS 16688:2017 | Guidelines for the selection of coating types, tests and methods of assessing the performance of coated aluminium in architectural applications |
| I.S. EN 1090-3:2008 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES |
| PREN 16759 : DRAFT 2014 | STRUCTURAL SEALANT GLAZING SYSTEMS (SSGS) |
| EN 1090-3:2008 | Execution of steel structures and aluminium structures - Part 3: Technical requirements for aluminium structures |
| ONORM EN 12020-1 : 2008 | ALUMINIUM AND ALUMINIUM ALLOYS - EXTRUDED PRECISION PROFILES IN ALLOYS EN AW-6060 AND EN AW-6063 - PART 1: TECHNICAL CONDITIONS FOR INSPECTION AND DELIVERY |
| 08/30186163 DC : DRAFT JULY 2008 | BS IEC 60092-306 - ELECTRICAL INSTALLATIONS IN SHIPS - PART 306: EQUIPMENT - LUMINAIRES AND LIGHTING ACCESSORIES |
| 17/30348949 DC : 0 | BS EN 1090-3 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES |
| BS EN 12020-1:2008 | Aluminium and aluminium alloys. Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 Technical conditions for inspection and delivery |
| UNI EN 12020-1 : 2008 | ALUMINIUM AND ALUMINIUM ALLOYS - EXTRUDED PRECISION PROFILES IN ALLOYS EN AW-6060 AND EN AW-6063 - PART 1: TECHNICAL CONDITIONS FOR INSPECTION AND DELIVERY |
| EN 12020-1:2008 | Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 1: Technical conditions for inspection and delivery |
| BS EN 1090-3:2008 | Execution of steel structures and aluminium structures Technical requirements for aluminium structures |
| UNE-EN 1090-3:2011 | Execution of steel structures and aluminium structures - Part 3: Technical requirements for aluminium structures |
| 14/30300917 DC : 0 | BS EN 16759 - STRUCTURAL SEALANT GLAZING SYSTEMS (SSGS) |
| IEC 60092-306:2009 | Electrical installations in ships - Part 306: Equipment - Luminaires and lighting accessories |
| DIN EN 12020-1:2008-06 | Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 1: Technical conditions for inspection and delivery |
| EN 971-1 : 1996 | PAINTS AND VARNISHES - TERMS AND DEFINITIONS FOR COATING MATERIALS - PART 1: GENERAL TERMS |
| EN ISO 3668:2001 | Paints and varnishes - Visual comparison of the colour of paints (ISO 3668:1998) |
| EN ISO 3231:1997 | Paints and varnishes - Determination of resistance to humid atmospheres containing sulfur dioxide (ISO 3231:1993) |
| EN ISO 2360:2017 | Non-conductive coatings on non-magnetic electrically conductive base metals - Measurement of coating thickness - Amplitude-sensitive eddy-current method (ISO 2360:2017) |
| ISO 6270-1:1998 | Paints and varnishes Determination of resistance to humidity Part 1: Continuous condensation |
| ISO 1520:2006 | Paints and varnishes Cupping test |
| EN ISO 2409:2013 | Paints and varnishes - Cross-cut test (ISO 2409:2013) |
| EN ISO 8130-9:1999 | Coating powders - Part 9: Sampling (ISO 8130-9:1992) |
| ISO 3668:2017 | Paints and varnishes — Visual comparison of colour of paints |
| ISO 2859-2:1985 | Sampling procedures for inspection by attributes — Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection |
| ISO 2810:2004 | Paints and varnishes Natural weathering of coatings Exposure and assessment |
| ISO 7724-3:1984 | Paints and varnishes Colorimetry Part 3: Calculation of colour differences |
| EN ISO 11341:2004 | Paints and varnishes - Artificial weathering and exposure to artificial radiation - Exposure to filtered xenon-arc radiation (ISO 11341:2004) |
| ISO 11341:2004 | Paints and varnishes Artificial weathering and exposure to artificial radiation Exposure to filtered xenon-arc radiation |
| EN ISO 1520:2006 | Paints and varnishes - Cupping test (ISO 1520:2006) |
| ISO 3696:1987 | Water for analytical laboratory use — Specification and test methods |
| ISO 9227:2017 | Corrosion tests in artificial atmospheres — Salt spray tests |
| EN ISO 3696:1995 | Water for analytical laboratory use - Specification and test methods (ISO 3696:1987) |
| ISO 8130-9:1992 | Coating powders Part 9: Sampling |
| ISO 1519:2011 | Paints and varnishes Bend test (cylindrical mandrel) |
| EN ISO 1519:2011 | Paints and varnishes - Bend test (cylindrical mandrel) (ISO 1519:2011) |
| ISO 2409:2013 | Paints and varnishes Cross-cut test |
| ISO 8565:2011 | Metals and alloys Atmospheric corrosion testing General requirements |
| EN ISO 8565:2011 | Metals and alloys - Atmospheric corrosion testing - General requirements (ISO 8565:2011) |
| EN 573-3:2013 | Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products |
| ISO 2813:2014 | Paints and varnishes — Determination of gloss value at 20°, 60° and 85° |
| EN ISO 2813:2014 | Paints and varnishes - Determination of gloss value at 20°, 60° and 85° (ISO 2813:2014) |
| ISO 3231:1993 | Paints and varnishes — Determination of resistance to humid atmospheres containing sulfur dioxide |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.