• There are no items in your cart

EN 12244-1:1998

Withdrawn
Withdrawn

A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

DIRECT GAS-FIRED WASHING MACHINES, OF NOMINAL HEAT INPUT NOT EXCEEDING 20 KW - PART 1: SAFETY
Withdrawn date

01-31-2011

Published date

01-12-2013

FOREWORD
1 Scope
2 Normative references
3 Definitions
    3.1 Direct gas-fired washing appliance
    3.2 Gases
    3.3 Appliance construction
    3.4 Immobilizing an adjuster or a control
    3.5 Appliance performance
    3.6 Marking of the appliance and packaging
4 Classification
    4.1 Classification of gases
    4.2 Classification of appliances
5 Construction and design requirements
    5.1 General
          5.1.1 Conversion to different gases
          5.1.2 Materials and method of construction
          5.1.3 Screws
          5.1.4 Maintenance and use
          5.1.5 Thermal insulation
          5.1.6 Connections
          5.1.7 Supply of combustion air and evacuation
                  of combustion products
          5.1.8 Soundness
          5.1.9 Water filter
          5.1.10 Checking the state of operation
          5.1.11 Electrical equipment
          5.1.12 Motors
          5.1.13 Operational safety in the event of
                  fluctuation, interruption and restoration
                  of the auxiliary energy
    5.2 Requirements for adjusting, control and safety
          devices
          5.2.1 General
          5.2.2 Automatic shut-off valves
          5.2.3 Multifunctional controls
          5.2.4 Flame supervision devices
          5.2.5 Governors
          5.2.6 Gas rate adjusters
          5.2.7 Automatic burner control systems
          5.2.8 Gas strainers
          5.2.9 Atmosphere sensing device
          5.2.10 Spillage monitoring device
    5.3 Ignition devices
          5.3.1 General
          5.3.2 Ignition device for the main burner
          5.3.3 Ignition burners
    5.4 Ignition burner or start-gas flame establishment
    5.5 Main flame establishment
          5.5.1 Establishment by means of an ignition
                  burner or start-gas flame
          5.5.2 Direct establishment of the main flame
                  e.g. spark ignition hot surface igniter
    5.6 Burners
    5.7 Thermostats and control of water temperature
          5.7.1 General requirements
          5.7.2 Temperature limiting device
    5.8 Water level control device
    5.9 Clocks and timing devices
    5.10 Pressure test points
    5.11 Mechanical hazards
          5.11.1 General
          5.11.2 Requirements for appliances with an
                  opening dimension exceeding 30 cm and a
                  drum having a volume exceeding 100 dm
    5.12 Appliance stability
6 Operational safety
    6.1 General
          6.1.1 Characteristics of test gases: reference
                  and limit gases
          6.1.2 Conditions for preparation of test gases
          6.1.3 Practical application of test gases
          6.1.4 Test pressures
          6.1.5 Test procedures
          6.1.6 Test room
          6.1.7 Preparation of the appliance
          6.1.8 Test conditions
    6.2 Screws
          6.2.1 Requirements
          6.2.2 Tests
    6.3 Manually operated devices of the automatic
          burner control system
          6.3.1 Requirements
          6.3.2 Tests
    6.4 Mechanical hazards
          6.4.1 General
          6.4.2 Additional requirements for appliances
                  with an opening dimension exceeding
                  30 cm and a drum having a volume
                  exceeding 100 dm
    6.5 Stability of appliances
          6.5.1 Requirements
          6.5.2 Tests
    6.6 Soundness
          6.6.1 Soundness of the gas circuit
          6.6.2 Soundness of the water circuit
          6.6.3 Soundness of the combustion circuit and
                  correct evacuation of the combustion
                  products for type B appliances
    6.7 Nominal heat input
          6.7.1 General
          6.7.2 Requirements
          6.7.3 Tests
    6.8 Heat input of ignition burners
          6.8.1 Requirements
          6.8.2 Tests
    6.9 Burners
          6.9.1 Resistance to overheating
          6.9.2 Escape of unburnt gas
    6.10 Limiting temperature of various parts of the
          appliance
    6.11 Limiting temperature of floor, walls and worktop
    6.12 Limiting temperature of components
    6.13 Motor limiting temperatures
    6.14 Flue gas temperature
    6.15 Ignition, cross-lighting and flame stability
    6.16 Flame supervision devices
    6.17 Governors
    6.18 Atmosphere sensing device
    6.19 Spillage monitoring device
    6.20 Combustion
    6.21 Soot deposition
    6.22 Cyclic operation
    6.23 Temperature limiting device
    6.24 Water level control device
7 Marking
    7.1 Marking of the appliance
    7.2 Marking of the packaging
    7.3 Utilization of symbols on the appliance and
          packaging
    7.4 Instructions
    7.5 Presentation
Annex A (informative) National situations
    A.1 Categories listed in the body of the standard
           marketed in the different countries
    A.2 Appliance supply pressures corresponding to the
           categories given in A.1
    A.3 Special categories marketed nationally or
           locally and corresponding test gases
    A.4 Test gases corresponding to the special categories
           given in A.3
    A.5 Gas connections in the various countries
    A.6 Water connection conditions in common use in
           the various countries
    A.7 Flue connections in the various countries
    A.8 Equivalence rules
Annex B (normative) Protection against electric shock for
         high voltage ignition devices
    B.1 Protection against accessibility to live parts
    B.2 Requirements
    B.3 Test
    B.4 Measurement
    B.5 Protection
Annex C (normative) Description of the sealed room for the
         test appliances with atmosphere sensing devices
    C.1 Configuration of the sealed room
    C.2 Soundness of the room
    C.3 Effectiveness of mixing
Annex D (normative) Special national conditions
Annex ZA (informative) Clauses of this European Standard
         addressing essential requirements or other
         provisions of EU Directives

Defines the requirements and test procedures for construction, safety and marking of direct gas-fired washing appliances with or without heat exchanger or spin dryer, for types not in excess of a heat input of 20 kW, and those not exceeding a heat input of 20 kW. Not applicable to catalytic combustion appliances, appliances meant for use in locations with special conditions, eg corrosive or explosive atmosphere or appliances for use in vehicles or on board ships or aircraft. Describes only type testing.

Committee
TC 299
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Withdrawn

I.S. EN 12244-2:1998 DIRECT GAS-FIRED WASHING MACHINES, OF NOMINAL HEAT INPUT NOT EXCEEDING 20 KW - PART 2: RATIONAL USE OF ENERGY
BS EN 12244-2:1998 Direct gas-fired washing machines, of nominal heat input not exceeding 20 kW Rational use of energy
EN 12244-2:1998 DIRECT GAS-FIRED WASHING MACHINES, OF NOMINAL HEAT INPUT NOT EXCEEDING 20 KW - PART 2: RATIONAL USE OF ENERGY

IEC TS 60479-1:2005+AMD1:2016 CSV Effects of current on human beings and livestock - Part 1: Generalaspects
ISO 6976:2016 Natural gas — Calculation of calorific values, density, relative density and Wobbe indices from composition
EN 1057:2006+A1:2010 Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications
EN 60730-2-9:2010 Automatic electrical controls for household and similar use - Part 2-9: Particular requirements for temperature sensing controls
EN 161:2011+A3:2013 Automatic shut-off valves for gas burners and gas appliances
ISO 1182:2010 Reaction to fire tests for products Non-combustibility test
ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation
EN 437:2003+A1:2009 Test gases - Test pressures - Appliance categories
EN 125:2010+A1:2015 Flame supervision devices for gas burning appliances - Thermoelectric flame supervision devices
EN 126:2012 Multifunctional controls for gas burning appliances
EN 60584-1:2013 Thermocouples - Part 1: EMF specifications and tolerances
CR 1472:1997 General guidance for the marking of gas appliances
EN 60335-2-7:2010/A11:2013 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-7: PARTICULAR REQUIREMENTS FOR WASHING MACHINES
EN 61058-1:2002/A2:2008 SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS
EN 60335-1:2012/A13:2017 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED)
EN 298:2012 Automatic burner control systems for burners and appliances burning gaseous or liquid fuels
EN 88:1991/A1:1996 PRESSURE GOVERNORS FOR GAS APPLIANCES FOR INLET PRESSURE UP TO 200 MBAR
EN 23166:1993/AC:1994 CODES FOR THE REPRESENTATION OF NAMES OF COUNTRIES
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
EN 60068-2-63 : 1994 ENVIRONMENTAL TESTING - PART 2: TEST METHODS - TEST EG: IMPACT, SPRING HAMMER
ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
EN 60730-1:2016 Automatic electrical controls - Part 1: General requirements
EN 257:2010 Mechanical thermostats for gas-burning appliances

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.