• There are no items in your cart

EN 12566-3:2016

Current
Current

The latest, up-to-date edition.

Small wastewater treatment systems for up to 50 PT - Part 3: Packaged and/or site assembled domestic wastewater treatment plants
Published date

08-31-2016

European foreword
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviated
  terms
4 Product characteristics
5 Testing, assessment and sampling methods
6 Assessment and verification of constancy of
  performance - AVCP
7 Classification and designation (Nominal
  designation)
8 Marking, labelling and packaging
Annex A (normative) - Watertightness test
Annex B (normative) - Treatment efficiency test
        procedure
Annex C (normative) - Test methods for structural
        behaviour
Annex D (normative) - Mechanical characteristics
        used for structural behaviour calculation
Annex E (informative) - Analysis method
Annex ZA (informative) - Clauses of this European
         Standard addressing the provisions of the
         EU Construction Products Regulation
Bibliography

This European Standard specifies requirements, test methods, the marking and evaluation of conformity for packaged and/or site assembled domestic wastewater treatment plants (including guest houses and businesses) used for populations up to 50 inhabitants. Small wastewater treatment plants according to this European Standard are used for the treatment of raw domestic wastewater. It covers plants with tanks made of concrete, steel, PVC-U, Polyethylene (PE), Polypropylene (PP) and Glass Reinforced Polyester (GRP-UP). The test methods specified in this European Standard establish the performance of the plant, needed to verify its suitability for the end use. This European Standard applies for small wastewater treatment plants for use buried in the ground where no vehicle loads are applied to the product. This European Standard applies to plants where all prefabricated components are factory or site-assembled by one manufacturer and which are tested as a whole.

Committee
CEN/TC 165
DevelopmentNote
Supersedes PREN 12566-3. (09/2016)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current

S.R. CEN/TR 16394:2014 CHARACTERIZATION OF SLUDGES - PROTOCOL FOR PREPARING SYNTHETIC SUSPENSIONS
17/30362689 DC : 0 BS EN 16941-2 - ON-SITE NON-POTABLE WATER SYSTEMS - PART 2: SYSTEMS FOR THE USE OF TREATED GREYWATER
06/30148351 DC : 0 EN 12566-6 - SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 6: PREFABRICATED TREATMENT UNITS FOR SEPTIC TANK EFFLUENT
I.S. EN 12566-7:2016 SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 7: PREFABRICATED TERTIARY TREATMENT UNITS
BS EN 12566-6:2013 Small wastewater treatment systems for up to 50 PT Prefabricated treatment units for septic tank effluent
EN 12566-6:2016 Small wastewater treatment systems for up to 50 PT - Part 6: Prefabricated treatment units for septic tank effluent
EN 12566-7:2016 Small wastewater treatment systems for up to 50 PT - Part 7: Prefabricated tertiary treatment units
CEN/TR 16394:2014/AC:2015 CHARACTERIZATION OF SLUDGES - PROTOCOL FOR PREPARING SYNTHETIC SUSPENSIONS
EN 12566-1:2016 Small wastewater treatment systems for up to 50 PT - Part 1: Prefabricated septic tanks
CEN/TR 12566-5:2008 Small wastewater treatment systems up to 50 PT - Part 5: Pre-treated Effluent Filtration systems
S.R. CEN/TR 12566-5:2008 SMALL WASTEWATER TREATMENT SYSTEMS UP TO 50 PT - PART 5: PRETREATED EFFLUENT FILTRATION SYSTEMS
I.S. EN 12566-1:2016 SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 1: PREFABRICATED SEPTIC TANKS
VDI 2050 Blatt 2:2011-11 Requirements for mechanical equipment rooms - Sanitary engineering
09/30203912 DC : 0 BS EN 12566-7 - SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 7: PREFABRICATED TERTIARY TREATMENT UNITS
15/30317327 DC : 0 BS EN 16941-1 - ON-SITE NON-POTABLE WATER SYSTEMS - PART 1: SYSTEMS FOR THE USE OF RAINWATER
UNE-EN 12566-6:2017 Small wastewater treatment systems for up to 50 PT - Part 6: Prefabricated treatment units for septic tank effluent
UNE-EN 12566-7:2017 Small wastewater treatment systems for up to 50 PT - Part 7: Prefabricated tertiary treatment units
UNE-EN 12566-1:2017 Small wastewater treatment systems for up to 50 PT - Part 1: Prefabricated septic tanks
08/30187745 DC : 0 BS EN 12566-6 - SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 6: PREFABRICATED TREATMENT UNITS FOR SEPTIC TANK EFFLUENT
I.S. EN 12566-6:2016 SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 6: PREFABRICATED TREATMENT UNITS FOR SEPTIC TANK EFFLUENT
BS EN 12566-7:2013 Small wastewater treatment systems for up to 50 PT Prefabricated tertiary treatment units
BS EN 12566-1:2000 Small wastewater treatment systems for up to 50 PT Prefabricated septic tanks

ISO 5664:1984 Water quality — Determination of ammonium — Distillation and titration method
EN ISO 13229:2011 Thermoplastics piping systems for non-pressure applications - Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings - Determination of the viscosity number and K-value (ISO 13229:2010)
EN 14150:2006 Geosynthetic barriers - Determination of permeability to liquids
ISO 6778:1984 Water quality — Determination of ammonium — Potentiometric method
ISO 13229:2010 Thermoplastics piping systems for non-pressure applications Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings Determination of the viscosity number and K-value
ISO 5663:1984 Water quality — Determination of Kjeldahl nitrogen — Method after mineralization with selenium
EN ISO 11885:2009 Water quality - Determination of selected elements by inductively coupled plasma optical emission spectrometry (ICP-OES) (ISO 11885:2007)
EN ISO 9967:2016 Thermoplastics pipes - Determination of creep ratio (ISO 9967:2016)
EN 978:1997 Underground tanks of glass-reinforced plastics (GRP) - Determination of factor alpha and factor beta
ISO 5815:1989 Water quality Determination of biochemical oxygen demand after 5 days (BOD 5) Dilution and seeding method
EN 1899-1 : 1998 WATER QUALITY - DETERMINATION OF BIOCHEMICAL OXYGEN DEMAND AFTER N DAYS (BODN) - DILUTION AND SEEDING METHOD WITH ALLYTHIOUREA ADDITION
ISO 1133-1:2011 Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method
EN 872:2005 Water quality - Determination of suspended solids - Method by filtration through glass fibre filters
EN 976-1:1997 Underground tanks of glass-reinforced plastics (GRP) - Horizontal cylindrical tanks for the non-pressure storage of liquid petroleum based fuels - Part 1: Requirements and test methods for single wall tanks
EN ISO 11732:2005 Water quality - Determination of ammonium nitrogen - Method by flow analysis (CFA and FIA) and spectrometric detection (ISO 11732:2005)
EN ISO 527-2:2012 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012)
EN 25663 : 1993 WATER QUALITY - DETERMINATION OF KJELDAHL NITROGEN - METHOD AFTER MINERALIZATION WITH SELENIUM
EN ISO 178:2010/A1:2013 PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010/AMD 1:2013)
ISO 11732:2005 Water quality — Determination of ammonium nitrogen — Method by flow analysis (CFA and FIA) and spectrometric detection
EN ISO 1133-2:2011 Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 2: Method for materials sensitive to time-temperature history and/or moisture (ISO 1133-2:2011)
EN ISO 11905-1 : 1998 WATER QUALITY - DETERMINATION OF NITROGEN - METHOD USING OXIDATIVE DIGESTION WITH PEROXODISULFATE
EN 12311-2:2013 Flexible sheets for waterproofing - Determination of tensile properties - Part 2: Plastic and rubber sheets for roof waterproofing
ISO 11905-1:1997 Water quality — Determination of nitrogen — Part 1: Method using oxidative digestion with peroxodisulfate
ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
EN 16323:2014 Glossary of wastewater engineering terms
ISO 6060:1989 Water quality — Determination of the chemical oxygen demand
ISO 11885:2007 Water quality Determination of selected elements by inductively coupled plasma optical emission spectrometry (ICP-OES)
EN 12260:2003 Water quality - Determination of nitrogen - Determination of bound nitrogen (TNb), following oxidation to nitrogen oxides
ISO 15681-2:2003 Water quality Determination of orthophosphate and total phosphorus contents by flow analysis (FIA and CFA) Part 2: Method by continuous flow analysis (CFA)
ISO 10304-1:2007 Water quality Determination of dissolved anions by liquid chromatography of ions Part 1: Determination of bromide, chloride, fluoride, nitrate, nitrite, phosphate and sulfate
EN ISO 15681-2:2004 Water quality - Determination of orthophosphate and total phosphorus contents by flow analysis (FIA and CFA) - Part 2: Method by continuous flow analysis (CFA) (ISO 15681-2:2003)
ISO 2555:1989 Plastics Resins in the liquid state or as emulsions or dispersions Determination of apparent viscosity by the Brookfield Test method
EN 476:2011 General requirements for components used in drains and sewers
EN ISO 1133-1:2011 Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2011)
ISO 13395:1996 Water quality — Determination of nitrite nitrogen and nitrate nitrogen and the sum of both by flow analysis (CFA and FIA) and spectrometric detection
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
ISO 899-2:2003 Plastics Determination of creep behaviour Part 2: Flexural creep by three-point loading
EN 727:1994 Plastics piping and ducting systems - Thermoplastics pipes and fittings - Determination of Vicat softening temperature (VST)
ISO 15705:2002 Water quality Determination of the chemical oxygen demand index (ST-COD) Small-scale sealed-tube method
EN ISO 9969:2016 Thermoplastics pipes - Determination of ring stiffness (ISO 9969:2016)
EN ISO 6878:2004 Water quality - Determination of phosphorus - Ammonium molybdate spectrometric method (ISO 6878:2004)
EN ISO 14125:1998/A1:2011 FIBRE-REINFORCED PLASTIC COMPOSITES - DETERMINATION OF FLEXURAL PROPERTIES
ISO 9001:2015 Quality management systems — Requirements
EN 580:2003 Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) pipes - Test method for the resistance to dichloromethane at a specified temperature (DCMT)
ISO 14125:1998 Fibre-reinforced plastic composites Determination of flexural properties
EN 858-1:2002/A1:2004 SEPARATOR SYSTEMS FOR LIGHT LIQUIDS (E.G. OIL AND PETROL) - PART 1: PRINCIPLES OF PRODUCT DESIGN, PERFORMANCE AND TESTING, MARKING AND QUALITY CONTROL
ISO 9967:2016 Thermoplastics pipes Determination of creep ratio
ISO 6878:2004 Water quality — Determination of phosphorus — Ammonium molybdate spectrometric method
EN 1905:1998 Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) pipes, fittings and material - Method for assessment of the PVC content based on total chlorine content
ISO 1133-2:2011 Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 2: Method for materials sensitive to time-temperature history and/or moisture
EN ISO 2505:2005 Thermoplastics pipes - Longitudinal reversion - Test method and parameters (ISO 2505:2005)
EN 1992-1-1:2004/A1:2014 EUROCODE 2: DESIGN OF CONCRETE STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS
ISO 7150-1:1984 Water quality — Determination of ammonium — Part 1: Manual spectrometric method
EN ISO 899-2:2003/A1:2015 Plastics - Determination of creep behaviour - Part 2: Flexural creep by three-point loading - Amendment 1 (ISO 899-2:2003/Amd 1:2015)
ISO 178:2010 Plastics Determination of flexural properties
ISO 9969:2016 Thermoplastics pipes Determination of ring stiffness
EN ISO 10304-1:2009 Water quality - Determination of dissolved anions by liquid chromatography of ions - Part 1: Determination of bromide, chloride, fluoride, nitrate, nitrite, phosphate and sulfate (ISO 10304-1:2007)
EN 206:2013+A1:2016 Concrete - Specification, performance, production and conformity
EN ISO 14911 : 1999 WATER QUALITY - DETERMINATION OF DISSOLVED LI+, NA+, NH4+, K+, MN2+, CA2+, MG2+, SR2+ AND BA2+ USING ION CHROMATOGRAPHY - METHOD FOR WATER AND WASTE WATER
EN 1993-1-1:2005/A1:2014 EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS
ISO 14911:1998 Water quality Determination of dissolved Li+, Na+, NH4+, K+, Mn2+, Ca2+, Mg2+, Sr2+ and Ba2+ using ion chromatography Method for water and waste water
EN 10088-1:2014 Stainless steels - Part 1: List of stainless steels
ISO 2505:2005 Thermoplastics pipes — Longitudinal reversion — Test method and parameters
EN ISO 13395 : 1996 WATER QUALITY - DETERMINATION OF NITRITE NITROGEN AND NITRATE NITROGEN AND THE SUM OF BOTH BY FLOW ANALYSIS (CFA AND FIA) AND SPECTROMETRIC DETECTION

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.