• There are no items in your cart

EN 12601:2010

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Reciprocating internal combustion engine driven generating sets - Safety
Superseded date

06-01-2016

Published date

12-01-2010

Foreword
Introduction
1 Scope
2 Normative References
3 Terms and definitions
4 General
5 Hazards
6 Safety Requirements
7 Operating and maintenance instructions
8 Safety labels
9 Marking
Annex A (normative) - List of hazards
Annex B (normative) - Application of EN 60204-1 for
        generating sets
Annex ZA (informative) - Relationship between this
         European Standard and the Essential
         Requirements of EU Directive 2006/42/EC
Bibliography

This European Standard specifies the safety requirements for reciprocating internal combustion (RIC) engine driven generating sets up to 1 000 V consisting of a RIC engine, an alternating current (a.c.) generator including the additional equipment required for operating, e.g. controlgear, switchgear, auxiliary equipment. This European Standard is not applicable for generating sets which are manufactured before the date of its publication as a national EN standard.It applies to generating sets for land and marine use, excluding generating sets used on board of seagoing vessels and mobile offshore units as well as on aircraft or to propel road vehicles and locomotives. The special requirements needed to cover operation in potentially explosive atmospheres are not covered in this standard.The hazards relevant to RIC engine driven generating sets are identified in Annex A.

Committee
CEN/TC 270
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

Standards Relationship
UNE-EN 12601:2011 Identical
PN EN 12601 : 2011 Identical
NBN EN 12601 : 2011 Identical
BS EN 12601:2010 Identical
NS EN 12601 : 2010 Identical
DIN EN 12601:2011-07 Identical
UNI EN 12601 : 2011 Identical
NF EN 12601 : 2011 Identical
I.S. EN 12601:2010 Identical
SN EN 12601 : 2011 Identical
NEN EN 12601 : 2010 Identical

I.S. EN 12312-20:2005 AIRCRAFT GROUND SUPPORT EQUIPMENT - SPECIFIC REQUIREMENTS - PART 20: ELECTRICAL GROUND POWER UNITS
DIN EN 12312-20:2009-08 AIRCRAFT GROUND SUPPORT EQUIPMENT - SPECIFIC REQUIREMENTS - PART 20: ELECTRICAL GROUND POWER UNITS
EN 12312-20:2005+A1:2009 Aircraft ground support equipment - Specific requirements - Part 20: Electrical ground power units
02/714362 DC : DRAFT DEC 2002 EN 12312-20 - AIRCRAFT GROUND SUPPORT EQUIPMENT - SPECIFIC REQUIREMENTS - PART 20: GROUND POWER EQUIPMENT
BS EN 12312-20 : 2005 AIRCRAFT GROUND SUPPORT EQUIPMENT - SPECIFIC REQUIREMENTS - PART 20: ELECTRICAL GROUND POWER UNITS

EN 60332-3-25:2009 TESTS ON ELECTRIC AND OPTICAL FIBRE CABLES UNDER FIRE CONDITIONS - PART 3-25: TEST FOR VERTICAL FLAME SPREAD OF VERTICALLY-MOUNTED BUNCHED WIRES OR CABLES - CATEGORY D
EN 60332-3-23 : 2009 TESTS ON ELECTRIC AND OPTICAL FIBRE CABLES UNDER FIRE CONDITIONS - PART 3-23: TEST FOR VERTICAL FLAME SPREAD OF VERTICALLY-MOUNTED BUNCHED WIRES OR CABLES - CATEGORY B
EN 60332-3-21:2009 Tests on electric and optical fibre cables under fire conditions - Part 3-21: Test for vertical flame spread of vertically-mounted bunched wires or cables - Category A F/R
ISO 4871:1996 Acoustics — Declaration and verification of noise emission values of machinery and equipment
IEC 60332-3-25:2000+AMD1:2008 CSV Tests on electric and optical fibre cables under fire conditions - Part 3-25: Test for vertical flame spread of vertically-mounted bunched wires or cables - Category D
EN 547-2:1996+A1:2008 Safety of machinery - Human body measurements - Part 2: Principles for determining the dimensions required for access openings
EN 1088:1995+A2:2008 Safety of machinery - Interlocking devices associated with guards - Principles for design and selection
IEC 61310-2:2007 Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking
EN 981:1996+A1:2008 Safety of machinery - System of auditory and visual danger and information signals
ISO/TR 11688-1:1995 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning
ISO 8528-8:2016 Reciprocating internal combustion engine driven alternating current generating sets — Part 8: Requirements and tests for low-power generating sets
ISO 8528-3:2005 Reciprocating internal combustion engine driven alternating current generating sets Part 3: Alternating current generators for generating sets
ISO 8528-2:2005 Reciprocating internal combustion engine driven alternating current generating sets Part 2: Engines
ISO 2710-1:2000 Reciprocating internal combustion engines Vocabulary Part 1: Terms for engine design and operation
ISO 2710-2:1999 Reciprocating internal combustion engines Vocabulary Part 2: Terms for engine maintenance
IEC 60364-4-41:2005+AMD1:2017 CSV Low voltage electrical installations - Part 4-41: Protection for safety - Protection against electric shock
IEC 60073:2002 Basic and safety principles for man-machine interface, marking and identification - Coding principles for indicators and actuators
ISO 7967-9:2010 Reciprocating internal combustion engines Vocabulary of components and systems Part 9: Control and monitoring systems
EN 61310-2:2008 Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking
IEC 60331-11:1999+AMD1:2009 CSV Tests for electric cables under fire conditions - Circuit integrity - Part 11: Apparatus - Fire alone at a flame temperature of at least 750 °C
IEC 60332-3-23:2000+AMD1:2008 CSV Tests on electric and optical fibre cables under fire conditions - Part 3-23: Test for vertical flame spread of vertically-mounted bunched wires or cables - Category B
ISO 13732-1:2006 Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces
EN 60332-2-2:2004 Tests on electric and optical fibre cables under fire conditions - Part 2-2: Test for vertical flame propagation for a single small insulated wire or cable - Procedure for diffusion flame
ISO 8528-6:2005 Reciprocating internal combustion engine driven alternating current generating sets — Part 6: Test methods
EN 1679-1:1998+A1:2011 Reciprocating internal combustion engines - Safety - Part 1: Compression ignition engines
ISO 7967-4:2005 Reciprocating internal combustion engines Vocabulary of components and systems Part 4: Pressure charging and air/exhaust gas ducting systems
ISO 8178-3:1994 Reciprocating internal combustion engines Exhaust emission measurement Part 3: Definitions and methods of measurement of exhaust gas smoke under steady-state conditions
IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
ISO 8528-5:2013 Reciprocating internal combustion engine driven alternating current generating sets Part 5: Generating sets
EN ISO 13850:2015 Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015)
ISO 7967-1:2005 Reciprocating internal combustion engines — Vocabulary of components and systems — Part 1: Structure and external covers
IEC 60332-2-2:2004 Tests on electric and optical fibre cables under fire conditions - Part 2-2: Test for vertical flame propagation for a single small insulated wire or cable - Procedure for diffusion flame
ISO 8528-4:2005 Reciprocating internal combustion engine driven alternating current generating sets — Part 4: Controlgear and switchgear
ISO 3046-5:2001 Reciprocating internal combustion engines Performance Part 5: Torsional vibrations
EN ISO 13857:2008 Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)
EN 60332-1-2:2004/A11:2016 TESTS ON ELECTRIC AND OPTICAL FIBRE CABLES UNDER FIRE CONDITIONS - PART 1-2: TEST FOR VERTICAL FLAME PROPAGATION FOR A SINGLE INSULATED WIRE OR CABLE - PROCEDURE FOR 1 KW PRE-MIXED FLAME (IEC 60332-1-2:2004/A1:2015)
IEC 60332-1-1:2004+AMD1:2015 CSV Tests on electric and optical fibre cables under fire conditions - Part 1-1: Test for vertical flame propagation for a single insulatedwire or cable - Apparatus
IEC 60332-3-24:2000+AMD1:2008 CSV Tests on electric and optical fibre cables under fire conditions - Part 3-24: Test for vertical flame spread of vertically-mounted bunched wires or cables - Category C
ISO 8528-10:1998 Reciprocating internal combustion engine driven alternating current generating sets — Part 10: Measurement of airborne noise by the enveloping surface method
IEC 60332-1-2:2004+AMD1:2015 CSV Tests on electric and optical fibre cables under fire conditions - Part 1-2: Test for vertical flame propagation for a single insulatedwire or cable - Procedure for 1 kW pre-mixed flame
ISO 7967-8:2005 Reciprocating internal combustion engines — Vocabulary of components and systems — Part 8: Starting systems
EN ISO 13732-1:2008 Ergonomics of the thermal environment - Methods for the assessment of human responses to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1:2006)
ISO 7967-3:2010 Reciprocating internal combustion engines — Vocabulary of components and systems — Part 3: Valves, camshaft drives and actuating mechanisms
EN 60332-1-1:2004/A1:2015 Tests on electric and optical fibre cables under fire conditions - Part 1-1: Test for vertical flame propagation for a single insulated wire or cable - Apparatus
EN 60332-3-10:2009 Tests on electric and optical fibre cables under fire conditions - Part 3-10: Test for vertical flame spread of vertically-mounted bunched wires or cables - Apparatus
EN ISO 12100-1:2003/A1:2009 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
EN 953:1997+A1:2009 Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards
ISO 8528-9:2017 Reciprocating internal combustion engine driven alternating current generating sets — Part 9: Measurement and evaluation of mechanical vibrations
EN 60332-3-22:2009 Tests on electric and optical fibre cables under fire conditions - Part 3-22: Test for vertical flame spread of vertically-mounted bunched wires or cables - Category A
EN ISO 14122-2:2016 Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways (ISO 14122-2:2016)
ISO 12100-2:2003 Safety of machinery Basic concepts, general principles for design Part 2: Technical principles
IEC 60331-21:1999 Tests for electric cables under fire conditions - Circuit integrity - Part 21: Procedures and requirements - Cables of rated voltage up to and including 0,6/1,0 kV
ISO 13857:2008 Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs
EN ISO 12100-2:2003/A1:2009 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES
IEC 60332-3-21:2000 Tests on electric cables under fire conditions - Part 3-21: Test for vertical flame spread of vertically-mounted bunched wires or cables - Category A F/R
IEC 60332-2-1:2004 Tests on electric and optical fibre cables under fire conditions - Part 2-1: Test for vertical flame propagation for a single small insulated wire or cable - Apparatus
ISO 8528-7:2017 Reciprocating internal combustion engine driven alternating current generating sets — Part 7: Technical declarations for specification and design
ISO 8528-1:2005 Reciprocating internal combustion engine driven alternating current generating sets Part 1: Application, ratings and performance
ISO 3046-1:2002 Reciprocating internal combustion engines Performance Part 1: Declarations of power, fuel and lubricating oil consumptions, and test methods Additional requirements for engines for general use
ISO 8178-7:2015 Reciprocating internal combustion engines Exhaust emission measurement Part 7: Engine family determination
ISO 12100-1:2003 Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology
ISO 13850:2015 Safety of machinery Emergency stop function Principles for design
EN ISO 4871:2009 Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)
EN 60335-1:2012/A13:2017 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED)
IEC 61310-1:2007 Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals
EN 60332-2-1:2004 Tests on electric and optical fibre cables under fire conditions - Part 2-1: Test for vertical flame propagation for a single small insulated wire or cable - Apparatus
ISO 6826:1997 Reciprocating internal combustion engines Fire protection
EN 60332-3-24 : 2009 TESTS ON ELECTRIC AND OPTICAL FIBRE CABLES UNDER FIRE CONDITIONS - PART 3-24: TEST FOR VERTICAL FLAME SPREAD OF VERTICALLY-MOUNTED BUNCHED WIRES OR CABLES - CATEGORY C
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
ISO 7000:2014 Graphical symbols for use on equipment Registered symbols
ISO 14122-2:2016 Safety of machinery — Permanent means of access to machinery — Part 2: Working platforms and walkways
EN ISO 11688-1:2009 Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995)
IEC 60332-3-22:2000+AMD1:2008 CSV Tests on electric and optical fibre cables under fire conditions - Part 3-22: Test for vertical flame spread of vertically-mounted bunched wires or cables - Category A
EN 61310-1:2008 Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals
ISO 2261:1994 Reciprocating internal combustion engines Hand-operated control devices Standard direction of motion
IEC 60332-3-10:2000+AMD1:2008 CSV Tests on electric and optical fibre cables under fire conditions - Part 3-10: Test for vertical flame spread of vertically-mounted bunched wires or cables - Apparatus
ISO 8178-8:2015 Reciprocating internal combustion engines Exhaust emission measurement Part 8: Engine group determination
EN 60034-5:2001/A1:2007 ROTATING ELECTRICAL MACHINES - PART 5: DEGREES OF PROTECTION PROVIDED BY THE INTEGRAL DESIGN OF ROTATING ELECTRICAL MACHINES (IP CODE) - CLASSIFICATION
EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.