Skip to content
Please enter a keyword to search

  • EN 1295-1:1997

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    View superseded by
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Structural design of buried pipelines under various conditions of loading - Part 1: General requirements

    Available format(s): 

    Superseded date:  04-11-2019

    Language(s): 

    Published date:  07-23-1997

    Publisher:  Comite Europeen de Normalisation

    Add to Watchlist
    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Definitions
      3.1 Installation terms
      3.2 Design terms
    4 Requirements
    5 Basis of design procedures
      5.1 General
      5.2 External loads
      5.3 Limit states
      5.4 Longitudinal effects
    6 Additional considerations for pressure pipelines
      6.1 General
      6.2 Stresses and strains resulting from simultaneous
          loads
      6.3 Effect of pressure on deformation
      6.4 Buckling of pressure pipes
      6.5 Thrusts and longitudinal stresses
    7 Influence of construction procedures
      7.1 General
      7.2 Trenching procedures
      7.3 Pipe bedding
      7.4 Filling procedures
    8 Design philosophies and factors of safety
    Annexes
    A (informative) - Pipe definition according to
                      cross-sectional behaviour
    B (informative) - Nationally established methods of
                      design
      B.1 Identification of methods and addresses where they
          are available
          B.1.1 Austria
          B.1.2 Belgium
          B.1.3 Denmark
          B.1.4 Finland
          B.1.5 France
          B.1.6 Germany
          B.1.7 Netherlands
          B.1.8 Norway
          B.1.9 Spain
          B.1.10 Sweden
          B.1.11 Switzerland
          B.1.12 United Kingdom
      B.2 Description of methods
          B.2.1 Austria
          B.2.2 Belgium
          B.2.3 Denmark
          B.2.4 Finland
          B.2.5 France
          B.2.6 Germany
          B.2.7 Netherlands
          B.2.8 Norway
          B.2.9 Spain
          B.2.10 Sweden
          B.2.11 Switzerland
          B.2.12 United Kingdom

    Abstract - (Show below) - (Hide below)

    This standard specifies the requirements for the structural design of water supply pipelines, drains and sewers, and other water industry pipelines, whether operating under atmospheric, greater of lesser pressure. In addition, this standard gives guidance on the application of the established methods of design used in CEN member countries at the time of preparation of the standard.

    General Product Information - (Show below) - (Hide below)

    Committee CEN/TC 165
    Document Type Standard
    Publisher Comite Europeen de Normalisation
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    02/103343 DC : DRAFT MAY 2002 PREN 14457 - GENERAL REQUIREMENTS FOR COMPONENTS SPECIFICALLY DESIGNED FOR USE IN TRENCHLESS CONSTRUCTION OF DRAINS AND SEWERS
    DIN EN 15632-1:2015-03 District heating pipes - Pre-insulated flexible pipe systems - Part 1: Classification, general requirements and test methods (includes Amendment A1:2014)
    I.S. CEN TS 1852-3:2003 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE (PP) - PART 3: GUIDANCE FOR INSTALLATION
    BS EN 16323:2014 Glossary of wastewater engineering terms
    S.R. CEN/TR 1046:2013 THERMOPLASTICS PIPING AND DUCTING SYSTEMS - SYSTEMS OUTSIDE BUILDING STRUCTURES FOR THE CONVEYANCE OF WATER OR SEWAGE - PRACTICES FOR UNDERGROUND INSTALLATION
    S.R. CEN/TS 15223:2017 PLASTICS PIPING SYSTEMS - VALIDATED DESIGN PARAMETERS OF BURIED THERMOPLASTICS PIPING SYSTEMS
    UNI CEN/TS 14807 : 2014 PLASTICS PIPING SYSTEMS - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - GUIDANCE FOR THE STRUCTURAL ANALYSIS OF BURIED GRP-UP PIPELINES
    UNE-CEN/TR 1295-3:2011 IN Structural design of buried pipelines under various conditions of loading - Part 3: Common method
    BS EN 295-1:2013 Vitrified clay pipe systems for drains and sewers Requirements for pipes, fittings and joints
    CEN/TR 1295-2:2005 Structural design of buried pipelines under various conditions of loading - Part 2: Summary of nationally established methods of design
    CEN/TR 1295-3:2007 Structural design of buried pipelines under various conditions of loading - Part 3: Common method
    CEN/TS 14807:2013 Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for the structural analysis of buried GRP-UP pipelines
    CEN/TS 1852-3:2003/A1:2005 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE (PP) - PART 3: GUIDANCE FOR INSTALLATION
    ENV 1401-3:2001 Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3: Guidance for installation
    03/117538 DC : DRAFT NOV 2003 EN 14801 - CONDITIONS FOR PRESSURE CLASSIFICATION OF PRODUCTS FOR WATER AND WASTE WATER PIPELINES
    07/30160790 DC : 0 BS EN 15632-1 - DISTRICT HEATING PIPES - PRE-INSULATED FLEXIBLE PIPE SYSTEMS - PART 1: CLASSIFICATION, GENERAL REQUIREMENTS AND TEST METHODS
    13/30295203 DC : 0 BS EN 1610 - CONSTRUCTION AND TESTING OF DRAINS AND SEWERS
    PD CEN/TR 1295-4:2015 STRUCTURAL DESIGN OF BURIED PIPELINES UNDER VARIOUS CONDITIONS OF LOADING - PART 4: PARAMETERS FOR RELIABILITY OF THE DESIGN
    I.S. EN 16323:2014 GLOSSARY OF WASTEWATER ENGINEERING TERMS
    BS EN 15632-1 : 2009 DISTRICT HEATING PIPES - PRE-INSULATED FLEXIBLE PIPE SYSTEMS - PART 1: CLASSIFICATION, GENERAL REQUIREMENTS AND TEST METHODS
    PREN 295-1 : DRAFT 2010 VITRIFIED CLAY PIPE SYSTEMS FOR DRAINS AND SEWERS - PART 1: REQUIREMENTS FOR PIPES, FITTINGS AND JOINTS
    PREN 752 : DRAFT 2015 DRAIN AND SEWER SYSTEMS OUTSIDE BUILDINGS - SEWER SYSTEM MANAGEMENT
    DIN EN 752:2015-10 (Draft) DRAIN AND SEWER SYSTEMS OUTSIDE BUILDINGS - SEWER SYSTEM MANAGEMENT
    I.S. EN 1993-4-3:2007 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 4-3: PIPELINES
    I.S. EN 1610:2015 CONSTRUCTION AND TESTING OF DRAINS AND SEWERS
    S.R. CEN/TR 1295-3:2007 STRUCTURAL DESIGN OF BURIED PIPELINES UNDER VARIOUS CONDITIONS OF LOADING - PART 3: COMMON METHOD
    I.S. EN 295-1:2013 VITRIFIED CLAY PIPE SYSTEMS FOR DRAINS AND SEWERS - PART 1: REQUIREMENTS FOR PIPES, FITTINGS AND JOINTS
    15/30327642 DC : 0 BS EN 13476-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: GENERAL REQUIREMENTS AND PERFORMANCE CHARACTERISTICS
    DD CEN/TS 14758-3:2006 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE WITH MINERAL MODIFIER(S) (PP-MD) - PART 3: GUIDANCE FOR INSTALLATION
    DD CEN/TS 1852-3:2003 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE (PP) - PART 3: GUIDANCE FOR INSTALLATION
    CEN/TR 1046:2013 Thermoplastics piping and ducting systems - Systems outside building structures for the conveyance of water or sewage - Practices for underground installation
    I.S. EN 16932-1:2018 DRAIN AND SEWER SYSTEMS OUTSIDE BUILDINGS - PUMPING SYSTEMS - PART 1: GENERAL REQUIREMENTS
    UNI EN 16323 : 2014 GLOSSARY OF WASTEWATER ENGINEERING TERMS
    DIN EN 13476-1:2015-11 (Draft) PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: GENERAL REQUIREMENTS AND PERFORMANCE CHARACTERISTICS
    EN 16932-1:2018 Drain and sewer systems outside buildings - Pumping systems - Part 1: General requirements
    DIN EN 14801 E : 2006 CONDITIONS FOR PRESSURE CLASSIFICATION OF PRODUCTS FOR WATER AND WASTEWATER PIPELINES
    UNE-EN 1610:2016 Construction and testing of drains and sewers
    UNI EN 1993-4-3 : 2007 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 4-3: PIPELINES
    DIN EN 16323:2014-07 GLOSSARY OF WASTEWATER ENGINEERING TERMS
    I.S. EN 752:2017 DRAIN AND SEWER SYSTEMS OUTSIDE BUILDINGS - SEWER SYSTEM MANAGEMENT
    DD ENV 1401-3:2001 PLASTIC PIPING SYSTEMS FOR NON PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 3: GUIDANCE FOR INSTALLATION
    15/30325882 DC : 0 BS EN 16932-1 - DRAIN AND SEWER SYSTEMS OUTSIDE BUILDINGS - PUMPING SYSTEMS - PART 1: GENERAL REQUIREMENTS
    UNE-EN 15632-1:2010 District heating pipes - Pre-insulated flexible pipe systems - Part 1: Classification, general requirements and test methods
    PREN 1610 : DRAFT 2013 CONSTRUCTION AND TESTING OF DRAINS AND SEWERS
    I.S. CEN TS 14758-3:2006 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE WITH MINERAL MODIFIER(S) (PP-MD) - PART 3: GUIDANCE FOR INSTALLATION
    I.S. EN 15632-1:2009 DISTRICT HEATING PIPES - PRE-INSULATED FLEXIBLE PIPE SYSTEMS - PART 1: CLASSIFICATION, GENERAL REQUIREMENTS AND TEST METHODS
    BS EN 13476-1:2007 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: GENERAL REQUIREMENTS AND PERFORMANCE CHARACTERISTICS
    PREN 13476-1 : DRAFT 2015 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYLSEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL - PART 1: GENERAL REQUIREMENTS AND PERFORMANCE CHARACTERISTICS
    CEN/TS 15223:2017 Plastics piping systems - Validated design parameters of buried thermoplastics piping systems
    ISO 21138-1:2007 Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 1: Material specifications and performance criteria for pipes, fittings and system
    EN 13476-1:2018 Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1:General requirements and performance characteristics
    DIN EN 295-1:2013-05 VITRIFIED CLAY PIPE SYSTEMS FOR DRAINS AND SEWERS - PART 1: REQUIREMENTS FOR PIPES, FITTINGS AND JOINTS
    BS EN 805:2000 Water supply. Requirements for systems and components outside buildings
    PD CEN/TR 1295-2:2005 Structural design of buried pipelines under various conditions of loading Summary of nationally established methods of design
    BS EN 1610:2015 CONSTRUCTION AND TESTING OF DRAINS AND SEWERS
    BS EN 14801:2006 CONDITIONS FOR PRESSURE CLASSIFICATION OF PRODUCTS FOR WATER AND WASTEWATER PIPELINES
    BS EN 1444:2001 FIBRE-CEMENT PIPELINES - GUIDE FOR LAYING AND ON-SITE WORK PRACTICES
    EN 14801:2006 Conditions for pressure classification of products for water and wastewater pipelines
    EN 1610:2015 Construction and testing of drains and sewers
    EN 752:2017 Drain and sewer systems outside buildings - Sewer system management
    EN 805:2000 Water supply - Requirements for systems and components outside buildings
    EN 1444:2000 Fibre-cement pipelines - Guide for laying and on-site work practices
    EN 15632-1:2009+A1:2014 (edition 2) District heating pipes - Pre-insulated flexible pipe systems - Part 1: Classification, general requirements and test methods
    EN 295-1:2013 Vitrified clay pipe systems for drains and sewers - Part 1: Requirements for pipes, fittings and joints
    EN 16323:2014 Glossary of wastewater engineering terms
    11/30250267 DC : 0 BS EN 16323 - GLOSSARY OF WASTEWATER ENGINEERING TERMS
    10/30216984 DC : 0 BS EN 295-1 - VITRIFIED CLAY PIPE SYSTEMS FOR DRAINS AND SEWERS - PART 1: REQUIREMENTS FOR PIPES, FITTINGS AND JOINTS
    16/30314675 DC : 0 BS ISO 19469-1 - PLASTIC PIPING SYSTEMS FOR NON PRESSURE UNDERGROUND DRAINAGE - SINGLE WALL CORRUGATED PIPING SYSTEMS OF POLYETHYLENE (PE), POLYPROPYLENE (PP) AND UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: GENERAL REQUIREMENTS AND PERFORMANCE CHARACTERISTICS
    PD CEN/TS 14807:2013 PLASTICS PIPING SYSTEMS - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - GUIDANCE FOR THE STRUCTURAL ANALYSIS OF BURIED GRP-UP PIPELINES
    I.S. EN 13476-1:2007 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY (VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: GENERAL REQUIREMENTS AND PERFORMANCE CHARACTERISTICS
    CEN/TR 1295-4:2015 Structural design of buried pipelines under various conditions of loading - Part 4: Parameters for reliability of the design
    S.R. CEN/TR 1295-4:2015 STRUCTURAL DESIGN OF BURIED PIPELINES UNDER VARIOUS CONDITIONS OF LOADING - PART 4: PARAMETERS FOR RELIABILITY OF THE DESIGN
    S.R. CEN/TS 14807:2013 PLASTICS PIPING SYSTEMS - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - GUIDANCE FOR THE STRUCTURAL ANALYSIS OF BURIED GRP-UP PIPELINES
    UNE-EN 16323:2014 Glossary of wastewater engineering terms
    I.S. CEN TS 14807:2004 PLASTICS PIPING SYSTEMS - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - GUIDANCE FOR THE STRUCTURAL ANALYSIS OF BURIED GRP-UP PIPELINES
    UNE-EN 295-1:2013 Vitrified clay pipe systems for drains and sewers - Part 1: Requirements for pipes, fittings and joints
    CEN/TS 14758-3:2006 Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifier(s) (PP-MD) - Part 3: Guidance for installation
    DIN EN 14801:2006-09 CONDITIONS FOR PRESSURE CLASSIFICATION OF PRODUCTS FOR WATER AND WASTEWATER PIPELINES
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective