EN 13244-4:2002
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 4: Valves
02-01-2012
12-11-2002
Foreword
Introduction
1 Scope
2 Normative references
3 Definitions, symbols and abbreviations
4 Material
4.1 Compound for PE valve bodies
4.2 Material for non-polyethylene parts
5 General characteristics
5.1 Appearance of the valve
5.2 Design
5.3 Colour
6 Geometrical characteristics
6.1 General
6.2 Measurement of dimensions
6.3 Wall thickness at any point of the PE valve body
6.4 Dimensions of spigot ends for valves
6.5 Dimensions of valves with electrofusion sockets
6.6 Dimensions of the operating cap
7 Mechanical characteristics for assembled valves
7.1 General
7.2 Conditioning
7.3 Requirements
7.4 Retest in case of failure of hydrostatic strength
at 80 degree C
8 Physical characteristics
8.1 Conditioning
8.2 Requirements
9 Performance requirements
10 Marking
10.1 General
10.2 Marking on valves
10.3 Marking on a label
11 Packaging
Bibliography
This Part of EN 13244 specifies the characteristics of valves made from polyethylene (PE) intended to be used in the field of buried and above-ground pressure systems for water for general purposes, drainage and sewerage. It also specifies the test parameters for the test methods referred to in this Part of EN 13244. Valves made from material other than thermoplastics designed to a relevant standard(s) may be used in PE piping systems according to EN 13244 provided they have relevant PE connection ends see EN 13244-3 for butt fusion or electrofusion.
| Committee |
CEN/TC 155
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NS EN 13244-4 : 1ED 2003 | Identical |
| NBN EN 13244-4 : 2003 | Identical |
| UNI EN 13244-4 : 2004 | Identical |
| DIN EN 13244-4 E : 2003 | Identical |
| NF EN 13244-4 : 2003 | Identical |
| PN EN 13244-4 : 2004 | Identical |
| UNE-EN 13244-4:2003 | Identical |
| SN EN 13244-4 : 2003 | Identical |
| BS EN 13244-4:2002 | Identical |
| NEN EN 13244-4 : 2003 | Identical |
| I.S. EN 13244-4:2002 | Identical |
| DIN EN 13244-4:2003-04 | Identical |
| I.S. EN 13244-5:2002 | PLASTICS PIPING SYSTEMS FOR BURIED AND ABOVE-GROUND PRESSURE SYSTEMS FOR WATER FOR GENERAL PURPOSES DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - FITNESS FOR PURPOSE OF THE SYSTEM |
| UNI EN 15014 : 2008 | PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND SYSTEMS FOR WATER AND OTHER FLUIDS UNDER PRESSURE - PERFORMANCE CHARACTERISTICS FOR PIPES, FITTINGS AND THEIR JOINTS |
| DIN EN 15389 E : 2008 | INDUSTRIAL VALVES - PERFORMANCE CHARACTERISTICS OF THERMOPLASTIC VALVES WHEN USED AS CONSTRUCTION PRODUCTS |
| DIN EN 15014:2014-06 (Draft) | PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND SYSTEMS FOR WATER AND OTHER FLUIDS UNDER PRESSURE - PERFORMANCE CHARACTERISTICS FOR PIPES, FITTINGS AND THEIR JOINTS |
| BS EN 15014:2007 | Plastics piping systems. Buried and above ground systems for water and other fluids under pressure. Performance characteristics for pipes, fittings and their joints |
| DIN EN 13244-5:2003-04 | PLASTICS PIPING SYSTEMS FOR BURIED AND ABOVE-GROUND PRESSURE SYSTEMS FOR WATER FOR GENERAL PURPOSES, DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - PART 5: FITNESS FOR PURPOSE OF THE SYSTEM |
| EN 13244-5:2002 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| DIN EN 15014:2008-01 | Plastics piping systems - Buried and above ground systems for water and other fluids under pressure - Performance characteristics for pipes, fittings and their joints |
| I.S. EN 15014:2007 | PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND SYSTEMS FOR WATER AND OTHER FLUIDS UNDER PRESSURE - PERFORMANCE CHARACTERISTICS FOR PIPES, FITTINGS AND THEIR JOINTS |
| I.S. CEN TS 13244-7:2003 | PLASTICS PIPING SYSTEMS FOR BURIED AND ABOVE-GROUND PRESSURE SYSTEMS FOR WATER FOR GENERAL PURPOSES, DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
| DIN EN 15014 E : 2008 | PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND SYSTEMS FOR WATER AND OTHER FLUIDS UNDER PRESSURE - PERFORMANCE CHARACTERISTICS FOR PIPES, FITTINGS AND THEIR JOINTS |
| BS EN 13244-5:2002 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage. Polyethylene (PE) Fitness for purpose of the system |
| EN 15014:2007 | Plastics piping systems - Buried and above ground systems for water and other fluids under pressure - Performance characteristics for pipes, fittings and their joints |
| DD CEN/TS 13244-7:2003 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage. Polyethylene (PE) Guidance for the assessment of conformity |
| DIN EN 15389:2008-10 | INDUSTRIAL VALVES - PERFORMANCE CHARACTERISTICS OF THERMOPLASTIC VALVES WHEN USED AS CONSTRUCTION PRODUCTS |
| CEN/TS 13244-7 : 2003 | PLASTICS PIPING SYSTEMS FOR BURIED AND ABOVE-GROUND PRESSURE SYSTEMS FOR WATER FOR GENERAL PURPOSES, DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
| EN 13244-1:2002 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 1: General |
| EN 1705:1996 | Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after an external blow |
| EN 681-1:1996/A3:2005 | ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER |
| EN 728:1997 | Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time |
| BS EN 681-1:1996 | Elastomeric seals. Material requirements for pipe joint seals used in water and drainage applications Vulcanized rubber |
| EN 28233:1990 | Thermoplastics valves - Torque - Test method (ISO 8233:1988) |
| EN 12100:1997 | Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to bending between supports |
| EN 681-2:2000/A2:2005 | ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 2: THERMOPLASTIC ELASTOMERS |
| EN 1074-1:2000 | Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 1: General requirements |
| BS 7874:1998 | Method of test for microbiological deterioration of elastomeric seals for joints in pipework and pipelines |
| EN 1074-2:2000/A1:2004 | VALVES FOR WATER SUPPLY - FITNESS FOR PURPOSE REQUIREMENTS AND APPROPRIATE VERIFICATION TESTS - PART 2 - ISOLATING VALVES |
| EN 1680:1997 | Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanisms |
| ISO 10933:1997 | Polyethylene (PE) valves for gas distribution systems |
| EN 13244-3:2002 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 3: Fittings |
| PREN ISO 3126 : DRAFT 1999 | PLASTICS PIPING SYSTEMS - PLASTICS PIPING COMPONENTS - MEASUREMENT AND DETERMINATION OF DIMENSIONS |
| EN 917:1997 | Plastics piping systems - Thermoplastics valves - Test methods for resistance to internal pressure and leaktightness |
| EN ISO 1133:2005 | PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND THE MELT VOLUME-FLOW RATE (MVR) OF THE THERMOPLASTICS |
| EN 13244-5:2002 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| EN 13244-2:2002 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 2: Pipes |
| ISO 5208:2015 | Industrial valves Pressure testing of metallic valves |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.