• There are no items in your cart

EN 14154-3:2005+A2:2011

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Water meters - Part 3: Test methods and equipment
Superseded date

06-01-2014

Published date

04-06-2011

Foreword
1 Scope
2 Normative references
3 Reference conditions
4 Administrative and external examination for
  approval programme
5 Performance tests for approval programme
6 Performance tests related to influence quantities
Annex A (normative) - Irregularity in water velocity
        field
Annex B (informative) - Examples of methods and
        components used for testing Concentric Water
        Meters
Annex C (normative) - Equipment and method used to
        determine meter error
Annex D (informative) - Equipment and methods for pressure
        loss test
Annex E (informative) - Characteristics of reference devices
Annex ZA (informative) - Relationship between this European
         Standard and the Essential Requirements of EU
         Directive 22/2004/EC on Measuring Instruments
Bibliography

This document applies to water meters intended for residential, commercial, light industrial and industrial use, and specifies the test parameters and the test methods for water meters, irrespective of the design technologies, as specified in EN 14154-1:2005+A2, used to meter the actual volume of clean cold potable water or heated water, flowing through a fully charged, closed conduit. These water meters shall incorporate devices, which indicate the integrated volume.In the case where water meters having a value of Q3 > 160 m3/h, the test schedule may make provisions for modification of the Reference Conditions, to meet individual test laboratory limitations, when testing specifically for endurance or for performance under Influence Quantities.Meters thus tested shall be marked so as to unambiguously indicate part compliance with this document. To augment this marking the meter manufacturer shall, in addition, be obliged to fully disclose the specific non compliance(s) due to the test laboratory limitations.

Committee
CEN/TC 92
DevelopmentNote
2005 Edition Re-Issued in April 2011 & incorporates AMD 2 2011. (05/2011)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

14/30291768 DC : 0 BS EN 1434-4 - HEAT METERS - PART 4: PATTERN APPROVAL TESTS
I.S. EN 14154-4:2014 WATER METERS - PART 4: ADDITIONAL FUNCTIONALITIES
DIN EN 14268 E : 2005 IRRIGATION TECHNIQUES - METERS FOR IRRIGATION WATER
DIN EN 14154-2:2011-06 WATER METERS - PART 2: INSTALLATION AND CONDITIONS OF USE
DIN EN 14154-4:2015-02 Water meters - Part 4: Additional functionalities
DIN EN 14154-4 E : 2015 WATER METERS - PART 4: ADDITIONAL FUNCTIONALITIES
DIN EN 14268:2005-11 IRRIGATION TECHNIQUES - METERS FOR IRRIGATION WATER
BS EN 14154-2 : 2005 WATER METERS - PART 2: INSTALLATION AND CONDITIONS OF USE
BS EN 14154-4:2014 Water meters Additional functionalities
PREN 1434-4 : DRAFT 2014 HEAT METERS - PART 4: PATTERN APPROVAL TESTS
UNE-EN 14154-1:2005 Water meters - Part 1: General requirements
UNE-EN 14154-2:2005 Water meters - Part 2 : Installation and conditions of use
UNI EN 14268 : 2006 IRRIGATION TECHNIQUES - METERS FOR IRRIGATION WATER
UNI EN 14154-2 : 2011 WATER METERS - PART 2: INSTALLATION AND CONDITIONS OF USE
UNI EN 14154-1 : 2011 WATER METERS - PART 1: GENERAL REQUIREMENTS
ISO 20456:2017 Measurement of fluid flow in closed conduits — Guidance for the use of electromagnetic flowmeters for conductive liquids
BS EN 14268:2005 Irrigation techniques. Meters for irrigation water
BS EN 14154-1 : 2005 WATER METERS - PART 1: GENERAL REQUIREMENTS
EN 14154-2:2005+A2:2011 Water meters - Part 2: Installation and conditions of use
EN 14154-4:2014 Water meters - Part 4: Additional functionalities
EN 14268:2005/AC:2007 IRRIGATION TECHNIQUES - METERS FOR IRRIGATION WATER
UNE-EN 14154-4:2015 Water meters - Part 4: Additional functionalities
CSA C900.4 : 2013 HEAT METERS - PART 4: PATTERN APPROVAL TESTS
UNI EN 14154-4 : 2015 WATER METERS - PART 4: ADDITIONAL FUNCTIONALITIES
EN 14154-1:2005+A2:2011 Water meters - Part 1: General requirements
DIN EN 14154-1:2011-06 WATER METERS - PART 1: GENERAL REQUIREMENTS

EN 60068-3-1:2011 Environmental testing - Part 3-1: Supporting documentation and guidance - Cold and dry heat tests
EN 14154-1:2005+A2:2011 Water meters - Part 1: General requirements
EN 61000-4-11:2004/A1:2017 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-11: TESTING AND MEASUREMENT TECHNIQUES - VOLTAGE DIPS, SHORT INTERRUPTIONS AND VOLTAGE VARIATIONS IMMUNITY TESTS (IEC 61000-4-11:2004/A1:2017)
EN 60068-2-1:2007 Environmental testing - Part 2-1: Tests - Test A: Cold
EN 60068-2-2:2007 Environmental testing - Part 2-2: Tests - Test B: Dry heat
EN 60068-1:2014 Environmental testing - Part 1: General and guidance
2004/22/EC : 2004 DIRECTIVE 2004/22/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 31 MARCH 2004 ON MEASURING INSTRUMENTS
EN 60068-2-64:2008 ENVIRONMENTAL TESTING - PART 2-64: TESTS - TEST FH: VIBRATION, BROADBAND RANDOM AND GUIDANCE
EN 61000-4-2:2009 Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test
ISO 4064-3:2014 Water meters for cold potable water and hot water — Part 3: Test report format
ISO 4064-2:2014 Water meters for cold potable water and hot water Part 2: Test methods
EN 61000-4-3 : 2006 AMD 2 2010 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-3: TESTING AND MEASUREMENT TECHNIQUES - RADIATED, RADIO-FREQUENCY, ELECTROMAGNETIC FIELD IMMUNITY TEST
EN 14154-2:2005+A2:2011 Water meters - Part 2: Installation and conditions of use
OIML R 49-1 : 2013 WATER METERS FOR COLD POTABLE WATER AND HOT WATER - PART 1: METROLOGICAL AND TECHNICAL REQUIREMENTS
OIML R 49-2 : 2013 WATER METERS FOR COLD POTABLE WATER AND HOT WATER - PART 2: TEST METHODS
EN 61000-4-4:2012 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-4: TESTING AND MEASUREMENT TECHNIQUES - ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST (IEC 61000-4-4:2012)
IEC 60068-3-4:2001 Environmental testing - Part 3-4: Supporting documentation and guidance - Damp heat tests
EN 60068-2-30:2005 Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)
ISO 4064-1:2014 Water meters for cold potable water and hot water Part 1: Metrological and technical requirements
ISO/IEC Guide 98-3:2008 Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995)
EN 60068-2-31:2008 ENVIRONMENTAL TESTING - PART 2-31: TESTS - TEST EC: ROUGH HANDLING SHOCKS, PRIMARILY FOR EQUIPMENT-TYPE SPECIMENS
EN 60068-2-47:2005 Environmental testing - Part 2-47: Tests - Mounting of specimens for vibration, impact and similar dynamic tests

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.