• There are no items in your cart

EN 14396:2004

Current
Current

The latest, up-to-date edition.

Fixed ladders for manholes
Published date

01-14-2004

Foreword
1 Scope
2 Normative references
3 Terms, definitions and symbols
  3.1 Terms and definitions
  3.2 Symbols
4 Requirements
  4.1 General
  4.2 Materials
  4.3 Design requirements
      4.3.1 Types
      4.3.2 Dimensions
      4.3.3 Surface conditions
      4.3.4 Threaded joints
      4.3.5 Welded joints
      4.3.6 Rungs
      4.3.7 Attachment to manhole
  4.4 Load bearing capacity
      4.4.1 General
      4.4.2 Vertical imposed load on rungs
      4.4.3 Ladder strength by testing or calculation
      4.4.4 Pull out force for anchorage and strength of
            stay by calculation
5 Marking
6 Instructions for installation and use
7 Evaluation of conformity
  7.1 General
  7.2 Type testing (initial testing of the product)
  7.3 Factory production control (FPC)
      7.3.1 General
      7.3.2 Equipment
      7.3.3 Raw materials and components
      7.3.4 Product testing and evaluation
      7.3.5 Non conforming products
Annex A (normative) Ageing test of composite materials
      A.1 Principle
      A.2 Preparation of the samples
      A.3 Ageing test
      A.4 Shock test
      A.5 Bending test
      A.6 Acceptance criteria
Annex B (normative) Vertical loading test of rungs
      B.1 Apparatus
      B.2 Procedure
      B.3 Test report
Annex C (normative) Strength test of stringers of fixed ladders
        with two stringers and fixed ladders with one stringer
      C.1 Test equipment
      C.2 Procedure
      C.3 Test report
Annex D (normative) Strength test of the stringer for fixed ladders
        with one stringer
      D.1 Test procedure
      D.2 Test report
Annex E (normative) Calculation of strength of anchor points
      E.1 Fixed ladders with two stringers without fall arrester
      E.2 Fixed ladders with one stringer
Annex F (normative) Calculation of the fixed ladder
Annex ZA (informative) Clauses of this European Standard addressing
         the provisions of the EU Construction Products Directive
      ZA.1 Scope and relevant characteristics
      ZA.2 Procedure for attestation of conformity of fixed ladders
           for manholes
      ZA.3 CE marking and labelling
Bibliography

This standard applies to permanently fixed ladders in manholes. It specifies the performance criteria for the mechanical stability and resistance providing protection against falling.The ladders specified in this European Standard are suitable for use in sewage, rainwater, surface water and, subject to the requirements of national regulations, potable water environments.

Committee
CEN/TC 165
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current

Standards Relationship
PN EN 14396 : 2006 Identical
UNE-EN 14396:2004 Identical
NF EN 14396 : 2004 Identical
BS EN 14396:2004 Identical
DIN EN 14396 E : 2004 Identical
NEN EN 14396 : 2004 Identical
NBN EN 14396 : 2004 Identical
I.S. EN 14396:2004 Identical
SN EN 14396 : 2004 Identical
DIN EN 14396:2004-04 Identical
NS EN 14396 : 1ED 2004 Identical
UNI EN 14396 : 2004 Identical

DIN EN 15383:2014-02 PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS
14/30310792 DC : 0 BS EN 13598-2 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR MANHOLES AND INSPECTION CHAMBERS IN TRAFFIC AREAS AND DEEP UNDERGROUND INSTALLATIONS
UNE-EN 13598-2:2017 Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for manholes and inspection chambers
UNI EN 15383 : 2013-11 PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS
EN 476:2011 General requirements for components used in drains and sewers
10/30237537 DC : 0 EN 15383 - PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS
DIN EN 476:2011-04 General requirements for components used in drains and sewers
BS EN 476:2011 General requirements for components used in drains and sewers
I.S. EN 476:2011 GENERAL REQUIREMENTS FOR COMPONENTS USED IN DRAINS AND SEWERS
NF EN 476 : 2011 GENERAL REQUIREMENTS FOR COMPONENTS USED IN DRAINS AND SEWERS
I.S. EN 15383:2012 PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS
06/30124428 DC : 0 EN 13598-2 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY (VINYL CHLORIDE)(PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR MANHOLES AND INSPECTION CHAMBERS IN TRAFFIC AREAS AND DEEP UNDERGROUND INSTALLATIONS
UNI EN 476 : 2011 GENERAL REQUIREMENTS FOR COMPONENTS USED IN DRAINS AND SEWERS
DIN EN 13598-2 E : 2016 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR MANHOLES AND INSPECTION CHAMBERS
DIN EN 15383 E : 2014 PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS
PREN 13598-2 : DRAFT 2014 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR MANHOLES AND INSPECTION CHAMBERS IN TRAFFIC AREAS AND DEEP UNDERGROUND INSTALLATIONS
BS EN 15383 : 2012 PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS
ISO 13272:2011 Plastics piping systems for non-pressure underground drainage and sewerage — Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP), polypropylene with mineral modifiers (PP-MD) and polyethylene (PE) — Specifications for manholes and inspection chambers in traffic areas and underground installations
EN 13598-2:2016 Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for manholes and inspection chambers
UNE EN 15383 : 0 PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - MANHOLES AND INSPECTION CHAMBERS
EN 15383:2012+A1:2013 Plastics piping systems for drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Manholes and inspection chambers
DIN EN 13598-2:2016-09 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR MANHOLES AND INSPECTION CHAMBERS
I.S. EN 13598-2:2016 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR MANHOLES AND INSPECTION CHAMBERS
BS EN 13598-2:2009 Plastics piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Specifications for manholes and inspection chambers in traffic areas and deep underground installations
UNE-EN 476:2011 General requirements for components used in drains and sewers

EN 288-1:1992/A1:1997 SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - GENERAL RULES FOR FUSION WELDING
EN 288-3:1992/A1:1997 SPECIFICATION AND APPROVAL OF WELDING PROCEDURES FOR METALLIC MATERIALS - PART 3: WELDING PROCEDURE TESTS FOR THE ARC WELDING OF STEELS
EN ISO 1461:2009 Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods (ISO 1461:2009)
EN 10088-3:2014 Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
EN 288-4:1992/A1:1997 SPECIFICATION AND APPROVAL OF WELDING PROCEDURES FOR METALLIC MATERIALS - WELDING PROCEDURES FOR THE ARC WELDING OF ALUMINIUM AND ITS ALLOYS
EN 10025:1990/A1:1993 HOT ROLLED PRODUCTS OF NON-ALLOY STRUCTURAL STEELS - TECHNICAL DELIVERY CONDITIONS
ISO 1461:2009 Hot dip galvanized coatings on fabricated iron and steel articles — Specifications and test methods
EN ISO 179-1:2010 Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2010)
EN 288-2:1992/A1:1997 SPECIFICATION AND APPROVAL OF WELDING PROCEDURES FOR METALLIC MATERIALS - PART 2: WELDING PROCEDURE SPECIFICATION FOR ARC WELDING
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
ENV 10080 : 1995 STEEL FOR THE REINFORCEMENT OF CONCRETE WELDABLE RIBBED REINFORCING STEEL B500 - TECHNICAL DELIVERY CONDITIONS FOR BARS, COILS AND WELDED FABRIC
EN 10204:2004 Metallic products - Types of inspection documents
EN ISO 14125:1998/A1:2011 FIBRE-REINFORCED PLASTIC COMPOSITES - DETERMINATION OF FLEXURAL PROPERTIES
ISO 9001:2015 Quality management systems — Requirements
ISO 179-1:2010 Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 14125:1998 Fibre-reinforced plastic composites Determination of flexural properties
EN 365:2004/AC:2006 PERSONAL PROTECTIVE EQUIPMENT AGAINST FALLS FROM A HEIGHT - GENERAL REQUIREMENTS FOR INSTRUCTIONS FOR USE, MAINTENANCE, PERIODIC EXAMINATION, REPAIR, MARKING AND PACKAGING
ISO 4892-2:2013 Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
EN ISO 4892-2:2013 Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps (ISO 4892-2:2013)
EN 10088-1:2014 Stainless steels - Part 1: List of stainless steels

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.