Customer Support: +1 416-401-8730

Login to i2i Subscription Intertek.com
  • There are no items in your cart
Please enter a keyword to search
Advanced search

EN 15011:2011+A1:2014

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Cranes - Bridge and gantry cranes
Superseded date

12-23-2020

Published date

02-19-2014

Publisher

Comite Europeen de Normalisation

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or protective measures
6 Verification of safety requirements and/or protective
   measures
7 Information for use
Annex A (informative) - Guidance for specifying the
        operating duty according to EN 13001-1
Annex B (informative) - Guidance for specifying the
        classes P of average number of accelerations
        according to EN 13001-1
Annex C (informative) - Calculation of dynamic coefficient
        h(t)
Annex D (normative) - Loads caused by skewing
Annex E (informative) - Local stresses in wheel supporting
        flanges
Annex F (normative) - Noise test code
Annex G (informative) - Actions on crane supporting structures
        induced by cranes
Annex H (informative) - Selection of a suitable set of crane
        standards for a given application
Annex ZA (informative) - Relationship between this European
         standard and the Essential Requirements of
         EU Directive 2006/42/EC
Bibliography

This European Standard applies to bridge and gantry cranes able to travel by wheels on rails, runways or roadway surfaces, and to gantry cranes without wheels mounted in a stationary position.This European Standard specifies requirements for all significant hazards, hazardous situations and events relevant to bridge and gantry cranes when used as intended and under conditions foreseen by the manufacturer (see Clause 4).This European Standard does not include requirements for the lifting of persons.The specific hazards due to potentially explosive atmospheres, ionising radiation and operation in electromagnetic fields beyond the range of EN 61000-6-2 are not covered by this European Standard.This European Standard is applicable to bridge and gantry cranes manufactured after the date of its publication as an EN.

DevelopmentNote
2011 Edition Re-Issued in February 2014 & incorporates AMD 1 2014. (03/2014)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

UNE-EN 16851:2017 Cranes - Light crane systems
16/30341165 DC : 0 BS EN 14492-2 - CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS
BS EN 13001-1:2015 Cranes. General design General principles and requirements
EN 16851:2017 Cranes - Light crane systems
I.S. EN 13001-1:2015 CRANES - GENERAL DESIGN - PART 1: GENERAL PRINCIPLES AND REQUIREMENTS
VDI 4467:2014-12 Tandem operation of cranes/trolleys
VDI 3650:2013-02 Equipment for protecting cranes against drifting caused by wind
VDI 4412:2016-05 Cableless control of cranes
I.S. EN 16851:2017 CRANES - LIGHT CRANE SYSTEMS
DIN EN 13001-1:2015-06 CRANES - GENERAL DESIGN - PART 1: GENERAL PRINCIPLES AND REQUIREMENTS
UNE-EN 13001-1:2015 Cranes - General design - Part 1: General principles and requirements
15/30296047 DC : 0 BS EN 16851 - CRANES - LIGHT CRANE SYSTEMS
BS EN 16851:2017 Cranes. Light crane systems
DIN EN 16851:2015-05 (Draft) CRANES - LIGHT CRANE SYSTEMS
DIN EN 16851 E : 2017 CRANES - LIGHT CRANE SYSTEMS
DIN EN 16851:2017-06 Cranes - Light crane systems
EN 13001-1:2015 Cranes - General design - Part 1: General principles and requirements

ISO 11202:2010 Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections
EN 81-43:2009 Safety rules for the construction and installation of lifts - Special lifts for the transport of persons and goods - Part 43: Lifts for cranes
EN 1993-6:2007/AC:2009 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 6: CRANE SUPPORTING STRUCTURES
EN ISO 11204:2010 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections (ISO 11204:2010)
EN 12385-4:2002+A1:2008 Steel wire ropes - Safety - Part 4: Stranded ropes for general lifting applications
EN 13557:2003+A2:2008 Cranes - Controls and control stations
ISO 4871:1996 Acoustics — Declaration and verification of noise emission values of machinery and equipment
ISO 11660-5:2001 Cranes — Access, guards and restraints — Part 5: Bridge and gantry cranes
EN 60947-5-5 : 1997 AMD 2 2016 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-5: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - ELECTRICAL EMERGENCY STOP DEVICE WITH MECHANICAL LATCHING FUNCTION (IEC 60947-5-5:1997/A2:2016)
ISO 3744:2010 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane
ISO 15513:2000 Cranes — Competency requirements for crane drivers (operators), slingers, signallers and assessors
EN 13155:2003+A2:2009 Cranes - Safety - Non-fixed load lifting attachments
EN 60825-1:2014/AC:2017-06 SAFETY OF LASER PRODUCTS - PART 1: EQUIPMENT CLASSIFICATION AND REQUIREMENTS (IEC 60825-1:2014)
ISO 12480-1:1997 Cranes Safe use Part 1: General
ISO 9926-1:1990 Cranes Training of drivers Part 1: General
EN 12644-2:2000+A1:2008 Cranes - Information for use and testing - Part 2: Marking
ISO 9374-5:1991 Cranes Information to be provided Part 5: Overhead travelling cranes and portal bridge cranes
ISO/TR 11688-1:1995 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning
EN 894-2:1997+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays
IEC 60364-4-41:2005+AMD1:2017 CSV Low voltage electrical installations - Part 4-41: Protection for safety - Protection against electric shock
ISO 13732-1:2006 Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces
EN 1991-3:2006/AC:2012 EUROCODE 1 - ACTIONS ON STRUCTURES - PART 3: ACTIONS INDUCED BY CRANES AND MACHINERY
EN 349:1993+A1:2008 Safety of machinery - Minimum gaps to avoid crushing of parts of the human body
ISO 12488-1:2012 Cranes — Tolerances for wheels and travel and traversing tracks — Part 1: General
HD 60364-4-41:2017/A11:2017 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 4-41: PROTECTION FOR SAFETY - PROTECTION AGAINST ELECTRIC SHOCK
IEC 60204-11:2000 Safety of machinery - Electrical equipment of machines - Part 11: Requirements for HV equipment for voltages above 1 000 V a.c. or 1 500 V d.c. and not exceeding 36 kV
IEC 60825-1:2014 Safety of laser products - Part 1: Equipment classification and requirements
IEC 60204-32:2008 Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines
ISO 16881-1:2005 Cranes Design calculation for rail wheels and associated trolley track supporting structure Part 1: General
EN 13586:2004+A1:2008 Cranes - Access
EN 1050 : 1996 SAFETY OF MACHINERY - PRINCIPLES FOR RISK ASSESSMENT
EN 614-1:2006+A1:2009 Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles
EN ISO 13857:2008 Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)
EN ISO 11688-2 : 2000 ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 2: INTRODUCTION TO THE PHYSICS OF LOW-NOISE DESIGN
EN 12644-1:2001+A1:2008 Cranes - Information for use and testing - Part 1: Instructions
ISO 12100:2010 Safety of machinery — General principles for design — Risk assessment and risk reduction
ISO 9374-1:1989 Cranes Information to be provided Part 1: General
EN ISO 13732-1:2008 Ergonomics of the thermal environment - Methods for the assessment of human responses to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1:2006)
EN 60204-32:2008 Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines
EN ISO 11201:2010 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010)
EN 13001-2:2014 Crane safety - General design - Part 2: Load actions
ISO 4309:2010 Cranes Wire ropes Care and maintenance, inspection and discard
EN 13001-1:2015 Cranes - General design - Part 1: General principles and requirements
EN ISO 3744:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010)
EN 953:1997+A1:2009 Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards
ISO 13857:2008 Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs
ISO 6336-1:2006 Calculation of load capacity of spur and helical gears Part 1: Basic principles, introduction and general influence factors
ISO 11203:1995 Acoustics — Noise emitted by machinery and equipment — Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level
EN 13157:2004+A1:2009 Cranes - Safety - Hand powered cranes
EN 14492-2:2006+A1:2009/AC:2010 CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS
EN ISO 12100:2010 Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010)
ISO 2631-1:1997 Mechanical vibration and shock — Evaluation of human exposure to whole-body vibration — Part 1: General requirements
EN 60204-11:2000/corrigendum:2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 11: REQUIREMENTS FOR HV EQUIPMENT FOR VOLTAGES ABOVE 1000 V A.C. OR 1500 V D.C. AND NOT EXCEEDING 36 KV
EN ISO 13849-1:2015 Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015)
EN ISO 4871:2009 Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)
ISO 4301-1:2016 Cranes — Classification — Part 1: General
ISO 22986:2007 Cranes — Stiffness — Bridge and gantry cranes
EN 795:2012 Personal fall protection equipment - Anchor devices
ISO 8566-5:2017 Cranes — Cabins and control stations — Part 5: Overhead travelling and portal bridge cranes
EN ISO 11688-1:2009 Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995)
ISO 13849-1:2015 Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design
ISO 12482-1:1995 Cranes Condition monitoring Part 1: General
EN ISO 11202:2010 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010)
EN ISO 11203:2009 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level (ISO 11203:1995)
ISO 7752-5:1985 Lifting appliances Controls Layout and characteristics Part 5: Overhead travelling cranes and portal bridge cranes
ISO 11201:2010 Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections
ISO 11204:2010 Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections
PREN 13001-3-3 : DRAFT 2012 CRANES - GENERAL DESIGN - PART 3-3: LIMIT STATES AND PROOF OF COMPETENCE OF WHEEL/RAIL CONTACTS
ISO 10245-5:1995 Cranes — Limiting and indicating devices — Part 5: Overhead travelling and portal bridge cranes
CEN/TS 13001-3-2:2008 Cranes - General design - Part 3-2: Limit states and proof of competence of wire ropes in reeving systems
IEC 60947-5-5:1997+AMD1:2005+AMD2:2016 CSV Low-voltage switchgear and controlgear - Part 5-5: Control circuitdevices and switching elements - Electrical emergency stop device with mechanical latching function
EN 894-1:1997+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us