• There are no items in your cart

EN 40-6:2002

Current
Current

The latest, up-to-date edition.

Lighting columns - Part 6: Requirements for aluminium lighting columns
Published date

04-17-2002

Foreword
1 Scope
2 Normative references
3 Terms and Definitions
4 Materials
5 Dimensions
6 Design and design verification
7 Welding
8 Joints
9 Protection against mechanical impact
10 Internal finish and sharp edges
11 Corrosion protection
12 Marking
13 Conformity control
14 Acceptance criteria
15 Re-testing
16 Performance under vehicle impact - Passive safety
Annex A (informative) Corrosion protection for aluminium
         lighting columns
Annex B (informative) Recommendations for storage and
         installation
Annex C (normative) Initial type tests
Annex ZA (informative) Clauses of this European standard
         addressing the provisions of the EU Construction
         Products Directive

This European Standard specifies requirements for aluminium lighting columns. It includes materials and conformity control. It applies to post top columns not exceeding 20 m height for post top lanterns and to columns with brackets not exceeding 18 m height for side entry lanterns.This European Standard specifies performance related to the essential requirements of resistance to horizontal (wind) loads and performance under impact in support of the Essential Requirement No 4 Safety in use measured according to the corresponding test methods included in this European Standard or available in separate European Standards.It provides for the evaluation of conformity of the products to this European Standard.

Committee
CEN/TC 50
DevelopmentNote
Supersedes EN 40-3. Supersedes EN 40-4:1982 (01/2006)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current
Supersedes

Standards Relationship
UNE-EN 40-6:2003 Identical
NBN EN 40-6 : 2002 Identical
NF EN 40-6 : 2002 Identical
NEN EN 40-6 : 2002 Identical
NS EN 40-6 : 2ED 2002 Identical
I.S. EN 40-6:2002 Identical
PN EN 40-6 : 2004 Identical
SN EN 40-6 : 2002 Identical
UNE 72406:1984 Identical
UNI EN 40-6 : 2004 Identical
BS EN 40-6:2002 Identical
BS 5649-6:1982 Identical
DIN EN 40-6:2002-09 Identical
NFP 97 405 : 1980 Identical

17/30364350 DC : 0 BS EN 12767 - PASSIVE SAFETY OF SUPPORT STRUCTURES FOR ROAD EQUIPMENT - REQUIREMENTS AND TEST METHODS
EN 12767:2007 Passive safety of support structures for road equipment - Requirements, classification and test methods
12/30260931 DC : 0 BS EN 40-3-2 - LIGHTING COLUMNS - PART 3-2: DESIGN AND VERIFICATION - VERIFICATION BY TESTING
I.S. EN 12767:2007 PASSIVE SAFETY OF SUPPORT STRUCTURES FOR ROAD EQUIPMENT - REQUIREMENTS, CLASSIFICATION AND TEST METHODS
DIN EN 12767:2008-01 PASSIVE SAFETY OF SUPPORT STRUCTURES FOR ROAD EQUIPMENT - REQUIREMENTS, CLASSIFICATION AND TEST METHODS
UNE-EN 40-3-2:2013 Lighting columns - Part 3-2: Design and verification - Verification by testing
I.S. EN 40-3-2:2013 LIGHTING COLUMNS - PART 3-2: DESIGN AND VERIFICATION - VERIFICATION BY TESTING
PREN 12767 : DRAFT 2017 PASSIVE SAFETY OF SUPPORT STRUCTURES FOR ROAD EQUIPMENT - REQUIREMENTS AND TEST METHODS
BS EN 40-3-2:2013 Lighting columns Design and verification. Verification by testing
UNI EN 40-3-2 : 2013 LIGHTING COLUMNS - PART 3-2: DESIGN AND VERIFICATION - VERIFICATION BY TESTING
PREN 40-3-2 : DRAFT 2012 LIGHTING COLUMNS - DESIGN AND VERIFICATION - PART 3-2: VERIFICATION BY TESTING
13/30286641 DC : 0 BS EN 12767 - PASSIVE SAFETY OF SUPPORT STRUCTURES FOR ROAD EQUIPMENT - REQUIREMENTS AND TEST METHODS
DIN EN 40-3-2:2013-06 LIGHTING COLUMNS - PART 3-2: DESIGN AND VERIFICATION - VERIFICATION BY TESTING
EN 40-3-2:2013 Lighting columns - Part 3-2: Design and verification - Verification by testing
BS EN 12767:2007 Passive safety of support structures for road equipment. Requirements, classification and test methods

EN 40-3-1:2013 Lighting columns - Part 3-1: Design and verification - Specification for characteristic loads
EN 288-1:1992/A1:1997 SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - GENERAL RULES FOR FUSION WELDING
EN 40-3-2:2013 Lighting columns - Part 3-2: Design and verification - Verification by testing
EN 1011-4:2000/A1:2003 WELDING - RECOMMENDATIONS FOR WELDING OF METALLIC MATERIALS - PART 4: ARC WELDING OF ALUMINIUM AND ALUMINIUM ALLOYS
EN 485-3:2003 Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: Tolerances on dimensions and form for hot-rolled products
EN 485-4:1993 Aluminium and aluminium alloys - Sheet, strip and plate - Part 4: Tolerances on shape and dimensions for cold-rolled products
89/106/EEC : 1988 COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS
EN 288-4:1992/A1:1997 SPECIFICATION AND APPROVAL OF WELDING PROCEDURES FOR METALLIC MATERIALS - WELDING PROCEDURES FOR THE ARC WELDING OF ALUMINIUM AND ITS ALLOYS
EN 1011-1:2009 Welding - Recommendations for welding of metallic materials - Part 1: General guidance for arc welding
EN 755-8:2016 Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 8: Porthole tubes, tolerances on dimensions and form
EN 50102:1995/corrigendum Jul. 2002 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES FOR ELECTRICAL EQUIPMENT AGAINST EXTERNAL MECHANICAL IMPACTS (IK CODE)
EN 10025:1990/A1:1993 HOT ROLLED PRODUCTS OF NON-ALLOY STRUCTURAL STEELS - TECHNICAL DELIVERY CONDITIONS
EN 755-7:2016 Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 7: Seamless tubes, tolerances on dimensions and form
EN 288-2:1992/A1:1997 SPECIFICATION AND APPROVAL OF WELDING PROCEDURES FOR METALLIC MATERIALS - PART 2: WELDING PROCEDURE SPECIFICATION FOR ARC WELDING
EN 40-1:1991 Lighting columns - Part 1: Definitions and terms
EN 1706:2010 Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties
EN 12767:2007 Passive safety of support structures for road equipment - Requirements, classification and test methods
EN 10204:2004 Metallic products - Types of inspection documents
EN 288-8 : 1995 SPECIFICATION AND APPROVAL OF WELDING PROCEDURES FOR METALLIC MATERIALS - PART 8: APPROVAL BY A PRE-PRODUCTION WELDING TEST
EN 571-1:1997 Non destructive testing - Penetrant testing - Part 1: General principles
EN 970:1997 Non-destructive examination of fusion welds - Visual examination
PREN 40-3-3 : DRAFT 2012 LIGHTING COLUMNS - PART 3-3: DESIGN AND VERIFICATION - VERIFICATION BY CALCULATION

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.