EN 448:2015
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Fitting assemblies of steel service pipes, polyurethane thermal insulation and outer casing of polyethylene
Superseded date
10-26-2019
Published date
11-04-2015
Publisher
European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Test methods
6 Marking
Annex A (informative) - Guidelines for inspection and testing
Annex B (informative) - Procedures for polyethylene welding
Bibliography
This European Standard specifies requirements and test methods for fittings of prefabricated thermally insulated pipe-in-pipe assemblies comprising a steel service fitting from DN 20 to DN 1200, rigid polyurethane foam insulation and an outer casing of polyethylene for use in directly buried hot water networks with preinsulated pipe assemblies in accordance with EN 253.This European Standard covers the following fittings: bend, tee, reducer, single use compensator and anchor.This European Standard applies only to factory made prefabricated fitting assemblies and single use compensators for continuous operation with hot water at various temperatures in accordance with EN 253.This European Standard applies to fitting assemblies with a minimum design pressure of 16 bar (overpressure) complying with EN 13941.This European Standard does not include calculation rules for loads and stresses. The design and installation rules, for the system, are given in EN 13941.
| Committee |
CEN/TC 107
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| UNE-EN 448:2017 | Identical |
| NBN EN 448 : 2015 | Identical |
| NF EN 448 : 2015 | Identical |
| NEN EN 448 : 2015 | Identical |
| NS EN 448 : 2015 | Identical |
| I.S. EN 448:2015 | Identical |
| PN EN 448 : 2015 | Identical |
| SN EN 448 : 2016 | Identical |
| UNI EN 448 : 2009 | Identical |
| BS EN 448:2015 | Identical |
| DIN EN 448:2016-02 | Identical |
| DIN EN 15698-2 E : 2015 | DISTRICT HEATING PIPES - PREINSULATED BONDED TWIN PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - PART 2: FITTING AND VALVE ASSEMBLY OF STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE |
| 09/30197069 DC : 0 | BS EN 488 - DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - STEEL VALVE ASSEMBLY FOR STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE |
| 02/705050 DC : DRAFT APR 2002 | PREN 14419 - DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - SURVEILLANCE SYSTEMS |
| 18/30368654 DC : 0 | BS EN 488 - DISTRICT HEATING PIPES - BONDED SINGLE PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - FACTORY MADE STEEL VALVE ASSEMBLY FOR STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND A CASING OF POLYETHYLENE |
| BS EN 15698-2:2015 | District heating pipes. Preinsulated bonded twin pipe systems for directly buried hot water networks Fitting and valve assembly of steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
| I.S. EN 14419:2009 | DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - SURVEILLANCE SYSTEMS |
| I.S. EN 488:2015 | DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - STEEL VALVE ASSEMBLY FOR STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE |
| BS EN 489:2009 | District heating pipes. Preinsulated bonded pipe systems for directly buried hot water networks. Joint assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
| BS EN 14419:2009 | District heating pipes. Preinsulated bonded pipe systems for directly buried hot water networks. Surveillance systems |
| DIN EN 13941:2003-10 | DESIGN AND INSTALLATION OF PREINSULATED BONDED PIPE SYSTEMS FOR DIRECT HEATING |
| 14/30294473 DC : 0 | BS EN 488 - DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - STEEL VALVE ASSEMBLY FOR STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE |
| DIN EN 15698-2:2015-11 | DISTRICT HEATING PIPES - PREINSULATED BONDED TWIN PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - PART 2: FITTING AND VALVE ASSEMBLY OF STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE |
| I.S. EN 13941:2009 | DESIGN AND INSTALLATION OF PREINSULATED BONDED PIPE SYSTEMS FOR DISTRICT HEATING |
| 09/30186448 DC : 0 | BS EN 13941 - DESIGN AND INSTALLATION OF REINSULATED BONDED PIPE SYSTEMS FOR DISTRICT HEATING |
| 16/30342040 DC : 0 | BS EN 13941-2 - DISTRICT HEATING PIPES - DESIGN AND INSTALLATION OF THERMAL INSULATED BONDED SINGLE AND TWIN PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - PART 2: INSTALLATION |
| PREN 13941 : DRAFT 2009 | DESIGN AND INSTALLATION OF REINSULATED BONDED PIPE SYSTEMS FOR DISTRICT HEATING |
| 18/30372124 DC : DRAFT APR 2018 | BS EN 17248 - DISTRICT HEATING AND DISTRICT COOLING PIPE SYSTEMS - TERMS AND DEFINITIONS |
| DIN EN 488:2016-02 | DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - STEEL VALVE ASSEMBLY FOR STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE |
| I.S. EN 489:2009 | DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - JOINT ASSEMBLY FOR STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE |
| EN 488:2015 | District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Steel valve assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
| UNI EN 489 : 2009 | DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - JOINT ASSEMBLY FOR STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE |
| UNI EN 13941 : 2011 | DESIGN AND INSTALLATION OF PREINSULATED BONDED PIPE SYSTEMS FOR DISTRICT HEATING |
| UNI EN 14419 : 2009 | DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - SURVEILLANCE SYSTEMS |
| 17/30360921 DC : 0 | BS EN 489-1 - DISTRICT HEATING PIPES - BONDED SINGLE AND TWIN PIPE SYSTEMS FOR BURIED HOT WATER NETWORKS - PART 1: JOINT CASING ASSEMBLIES AND THERMAL INSULATION FOR HOT WATER NETWORKS IN ACCORDANCE WITH EN 13941-1 |
| I.S. EN 15698-2:2015 | DISTRICT HEATING PIPES - PREINSULATED BONDED TWIN PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - PART 2: FITTING AND VALVE ASSEMBLY OF STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE |
| DIN EN 14419 E : 2004 | DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - SURVEILLANCE SYSTEMS |
| DIN EN 489:2009-07 | District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Joint assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene; German and English version EN 489:2009 |
| UNE-EN 488:2012 | District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Steel valve assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
| BS EN 488:2015 | District heating pipes. Preinsulated bonded pipe systems for directly buried hot water networks. Steel valve assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
| BS EN 13941 : 2009 | DESIGN AND INSTALLATION OF PREINSULATED BONDED PIPE SYSTEMS FOR DISTRICT HEATING |
| EN 489:2009 | District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Joint assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
| EN 14419:2009 | District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Surveillance systems |
| EN 13941:2009+A1:2010 | Design and installation of preinsulated bonded pipe systems for district heating |
| EN 15698-2:2015 | District heating pipes - Preinsulated bonded twin pipe systems for directly buried hot water networks - Part 2: Fitting and valve assembly of steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
| 16/30342037 DC : 0 | BS EN 13941-1 - DISTRICT HEATING PIPES - DESIGN AND INSTALLATION OF THERMAL INSULATED BONDED SINGLE AND TWIN PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - PART 1: DESIGN |
| 13/30291075 DC : 0 | BS EN 15698-2 - DISTRICT HEATING PIPES - PREINSULATED BONDED TWIN PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - PART 2: FITTING AND VALVE ASSEMBLY OF STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE |
| PREN 17248 : DRAFT 2018 | DISTRICT HEATING AND DISTRICT COOLING PIPE SYSTEMS - TERMS AND DEFINITIONS |
| PREN 488 : DRAFT 2018 | DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - STEEL VALVE ASSEMBLY FOR STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE |
| DIN EN 14419:2004-03 | DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - SURVEILLANCE SYSTEMS |
| EN 13941:2009+A1:2010 | Design and installation of preinsulated bonded pipe systems for district heating |
| ISO 17636-1:2013 | Non-destructive testing of welds — Radiographic testing — Part 1: X- and gamma-ray techniques with film |
| EN ISO 9692-1:2013 | Welding and allied processes - Types of joint preparation - Part 1: Manual metal arc welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels (ISO 9692-1:2013) |
| ISO 2553:2013 | Welding and allied processes Symbolic representation on drawings Welded joints |
| EN ISO 5817:2014 | Welding - Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) - Quality levels for imperfections (ISO 5817:2014) |
| ISO 8501-1:2007 | Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings |
| ISO 11666:2010 | Non-destructive testing of welds Ultrasonic testing Acceptance levels |
| EN 488:2015 | District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Steel valve assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
| EN ISO 3452-1:2013 | Non-destructive testing - Penetrant testing - Part 1: General principles (ISO 3452-1:2013, Corrected version 2014-05-01) |
| ISO 23277:2015 | Non-destructive testing of welds Penetrant testing Acceptance levels |
| ISO 15590-1:2009 | Petroleum and natural gas industries Induction bends, fittings and flanges for pipeline transportation systems Part 1: Induction bends |
| EN ISO 10675-1:2016 | Non-destructive testing of welds - Acceptance levels for radiographic testing - Part 1: Steel, nickel, titanium and their alloys (ISO 10675-1:2016) |
| ISO 14732:2013 | Welding personnel Qualification testing of welding operators and weld setters for mechanized and automatic welding of metallic materials |
| EN ISO 23278 : 2015 | NON-DESTRUCTIVE TESTING OF WELDS - MAGNETIC PARTICLE TESTING - ACCEPTANCE LEVELS (ISO 23278:2015) |
| ISO 9606-1:2012 | Qualification testing of welders — Fusion welding — Part 1: Steels |
| EN ISO 23277:2015 | Non-destructive testing of welds - Penetrant testing - Acceptance levels (ISO 23277:2015) |
| EN 10216-2:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties |
| EN ISO 14732:2013 | Welding personnel - Qualification testing of welding operators and weld setters for mechanized and automatic welding of metallic materials (ISO 14732:2013) |
| ISO 2859-2:1985 | Sampling procedures for inspection by attributes — Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection |
| ISO 23278:2015 | Non-destructive testing of welds Magnetic particle testing Acceptance levels |
| ISO 5579:2013 | Non-destructive testing — Radiographic testing of metallic materials using film and X- or gamma rays — Basic rules |
| ISO 17640:2017 | Non-destructive testing of welds Ultrasonic testing Techniques, testing levels, and assessment |
| ISO 5817:2014 | Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections |
| ISO 3452-1:2013 | Non-destructive testing Penetrant testing Part 1: General principles |
| ISO 16810:2012 | Non-destructive testing — Ultrasonic testing — General principles |
| EN ISO 9934-1:2016 | Non-destructive testing - Magnetic particle testing - Part 1: General principles (ISO 9934-1:2016) |
| ISO 9692-1:2013 | Welding and allied processes — Types of joint preparation — Part 1: Manual metal arc welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels |
| EN 14419:2009 | District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Surveillance systems |
| EN ISO 16810:2014 | Non-destructive testing - Ultrasonic testing - General principles (ISO 16810:2012) |
| EN ISO 17637:2016 | Non-destructive testing of welds - Visual testing of fusion-welded joints (ISO 17637:2016) |
| EN ISO 5579:2013 | Non-destructive testing - Radiographic testing of metallic materials using film and X- or gamma rays - Basic rules (ISO 5579:2013) |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| ISO 17636-2:2013 | Non-destructive testing of welds — Radiographic testing — Part 2: X- and gamma-ray techniques with digital detectors |
| EN 12814-1:1999/AC:2003 | TESTING OF WELDED JOINTS OF THERMOPLASTICS SEMI-FINISHED PRODUCTS - PART 1: BEND TEST |
| EN 10217-2:2002/A1:2005 | WELDED STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 2: ELECTRIC WELDED NON-ALLOY AND ALLOY STEEL TUBES WITH SPECIFIED ELEVATED TEMPERATURE PROPERTIES |
| EN ISO 2553:2013 | Welding and allied processes - Symbolic representation on drawings - Welded joints (ISO 2553:2013) |
| ISO 9934-1:2016 | Non-destructive testing — Magnetic particle testing — Part 1: General principles |
| EN 489:2009 | District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Joint assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
| ISO 17637:2016 | Non-destructive testing of welds Visual testing of fusion-welded joints |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN ISO 17636-2:2013 | Non-destructive testing of welds - Radiographic testing - Part 2: X- and gamma-ray techniques with digital detectors (ISO 17636-2:2013) |
| EN 13018:2016 | NON-DESTRUCTIVE TESTING - VISUAL TESTING - GENERAL PRINCIPLES |
| EN ISO 8501-1:2007 | Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness - Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings (ISO 8501-1:2007) |
| ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials General rules |
| EN ISO 17636-1:2013 | Non-destructive testing of welds - Radiographic testing - Part 1: X- and gamma-ray techniques with film (ISO 17636-1:2013) |
| EN ISO 9606-1:2017 | Qualification testing of welders - Fusion welding - Part 1: Steels (ISO 9606-1:2012 including Cor 1:2012 and Cor 2:2013) |
| EN ISO 17638:2016 | Non-destructive testing of welds - Magnetic particle testing (ISO 17638:2016) |
| EN 253:2009+A2:2015 | District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Pipe assembly of steel service pipe, polyurethane thermal insulation and outer casing of polyethylene |
| ISO 10675-1:2016 | Non-destructive testing of welds Acceptance levels for radiographic testing Part 1: Steel, nickel, titanium and their alloys |
| EN 14870-1:2011 | Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 1: Induction bends (ISO 15590-1:2009 modified) |
| ISO 17638:2016 | Non-destructive testing of welds Magnetic particle testing |
| EN 10253-2:2007 | Butt-welding pipe fittings - Part 2: Non alloy and ferritic alloy steels with specific inspection requirements |
| EN 10217-1:2002/A1:2005 | WELDED STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - NON-ALLOY STEEL TUBES WITH SPECIFIED ROOM TEMPERATURE PROPERTIES |
| EN 10217-5:2002/A1:2005 | WELDED STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 5: SUBMERGED ARC WELDED NON-ALLOY AND ALLOY STEEL TUBES WITH SPECIFIED ELEVATED TEMPERATURE PROPERTIES |
| EN ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials - General rules (ISO 15607:2003) |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.