EN 60079-14:2014/AC:2016
Current
Current
The latest, up-to-date edition.
EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION (IEC 60079-14:2013/COR1:2016)
Published date
02-05-2016
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General
5 Selection of equipment
6 Protection from dangerous (incendive) sparking
7 Electrical protection
8 Switch-off and electrical isolation
9 Cables and wiring systems
10 Cable entry systems and blanking elements
11 Rotating electrical machines
12 Luminaires
13 Electric heating systems
14 Additional requirements for type of protection
'd' - Flameproof enclosures
15 Additional requirements for type of protection
'e' - Increased safety
16 Additional requirements for types of protection
'i' - Intrinsic safety
17 Additional requirements for pressurized enclosures
18 Additional requirements for type of protection 'n'
19 Additional requirements for type of protection
'o'- Oil immersion
20 Additional requirements for type of protection
'q' - Powder filling
21 Additional requirements for type of protection
'm' - Encapsulation
22 Additional requirements for type of protection
'op' - Optical radiation
23 Additional requirements for type of protection
't' - Protection by enclosure
Annex A (normative) - Knowledge, skills and competencies
of responsible persons, operatives/technicians
and designers
Annex B (informative) - Safe work procedure guidelines for
explosive gas atmospheres
Annex C (normative) - Initial inspection - Equipment-specific
inspection schedules
Annex D (informative) - Electrical installations in extremely
low ambient temperature
Annex E (informative) - Restricted breathing test for cables
Annex F (informative) - Installation of electrical trace
heating systems
Annex G (normative) - Potential stator winding discharge
risk assessment - Ignition risk factors
Annex H (normative) - Verification of intrinsically safe
circuits with more than one associated apparatus
with linear current/voltage characteristics
Annex I (informative) - Methods of determining the
maximum system voltages and currents in intrinsically
safe circuits with more than one associated apparatus
with linear current/voltage characteristics
(as required by Annex H)
Annex J (informative) - Determination of cable parameters
Annex K (normative) - Additional requirements for type
of protection 'op' - Optical radiation
Annex L (informative) - Examples of dust layers of excessive
thickness
Annex M (informative) - Hybrid mixtures
Bibliography
Annex ZA (normative) - Normative references to
international publications with their
corresponding European publications
Includes the specific requirements for the design, selection, erection and initial inspection of electrical installations in, or associated with, explosive atmospheres.
| Committee |
TC 31
|
| DevelopmentNote |
Supersedes EN 61241-14. (11/2011)
|
| DocumentType |
Standard
|
| PublisherName |
European Committee for Standards - Electrical
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| NBN EN 60079-14 : 2014 COR 2016 | Identical |
| VDE 0165-1:2014-10 | Identical |
| I.S. EN 60079-14:2014&AC:2016 | Identical |
| I.S. EN 60079-14:2014 | Identical |
| IEC 60079-14:2013 | Identical |
| CEI EN 60079-14/EC:2016 | Identical |
| UNE-EN 60079-14:2016 | Identical |
| DIN EN 60079-14:2014-10 | Identical |
| VDE 0165-1 : 2014 COR 1 2016 | Identical |
| BS EN 60079-14:2014 | Identical |
| SN EN 60079-14:2014 | Identical |
| NF EN 60079-14 : 2014 | Identical |
| VDE 0165-1 Berichtigung 1:2016-06 | Identical |
| NEN EN IEC 60079-14 : 2014 C1 2016 | Identical |
| DIN EN 60079-14 Berichtigung 1:2016-06 | Identical |
| PN EN 60079-14 : 2014 AC 2016 | Identical |
| IEEE 303-2004 | IEEE Recommended Practice for Auxiliary Devices for Rotating Electrical Machines in Class I, Division 2 and Zone 2 Locations |
| UNE-EN 60079-17:2014 | Explosive atmospheres - Part 17: Electrical installations inspection and maintenance |
| UNE-EN ISO 18081:2017 | Non-destructive testing - Acoustic emission testing (AT) - Leak detection by means of acoustic emission (ISO 18081:2016) |
| PREN 13952 : DRAFT 2015 | LPG EQUIPMENT AND ACCESSORIES - FILLING PROCEDURES FOR LPG CYLINDERS |
| PREN 50050-1 : DRAFT 2011 | ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 1: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE LIQUID COATING MATERIALS |
| 03/107320 DC : DRAFT APR 2003 | EN 14678-1 - LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 1: DISPENSERS |
| 03/119040 DC : DRAFT NOV 2003 | PREN 1010-1 - SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PRINTING AND PAPER CONVERTING MACHINES - PART 1: COMMON REQUIREMENTS |
| 13/30277457 DC : 0 | BS EN 1776 - GAS INFRASTRUCTURE - GAS MEASURING SYSTEMS - FUNCTIONAL REQUIREMENTS |
| CLC/TS 62603-1:2014 | Industrial process control systems - Guideline for evaluating process control systems - Part 1: Specifications |
| I.S. EN 60079-20-1:2010 | EXPLOSIVE ATMOSPHERES - PART 20-1: MATERIAL CHARACTERISTICS FOR GAS AND VAPOUR CLASSIFICATION - TEST METHODS AND DATA |
| PREN 1127-1 : DRAFT 2017 | EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 1: BASIC CONCEPTS AND METHODOLOGY |
| UNE-EN 50050-2:2014 | Electrostatic hand-held spraying equipment - Safety requirements - Part 2: Hand-held spraying equipment for ignitable coating powder |
| BS EN 60079-17:2014 | Explosive atmospheres Electrical installations inspection and maintenance |
| 11/30248849 DC : 0 | BS EN 50050-3:2011 - ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 3: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE FLOCK |
| BS EN 15001-2:2008 | Gas infrastructure. Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations Detailed functional requirements for commissioning, operation and maintenance |
| 09/30198043 DC : 0 | BS EN 1127-1 - EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 1: BASIC CONCEPTS AND METHODOLOGY |
| UNE-EN 60079-26:2015 | Explosive atmospheres - Part 26: Equipment with Equipment Protection Level (EPL) Ga |
| 13/30273033 DC : 0 | BS EN 1012-3 - COMPRESSORS AND VACUUM PUMPS - SAFETY REQUIREMENTS - PART 3: PROCESS COMPRESSORS |
| BS EN 61241-17:2005 | Electrical apparatus for use in the presence of combustible dust Inspection and maintenance of electrical installations in hazardous areas (other than mines) |
| CEI EN 60079-27 : 2010 | EXPLOSIVE ATMOSPHERES - PART 27: FIELDBUS INTRINSICALLY SAFE CONCEPT (FISCO) |
| BS EN 62305-3:2011 | Protection against lightning Physical damage to structures and life hazard |
| 12/30270980 DC : 0 | BS EN 1127-2 - EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 2: BASIC CONCEPTS AND METHODOLOGY FOR MINING |
| 10/30227671 DC : 0 | BS EN 14678-1 - LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 1: DISPENSERS |
| BS EN 50281-1-2:1999 | Electrical apparatus for use in the presence of combustible dust. Electrical apparatus protected by enclosures Selection, installation and maintenance |
| BS EN 14677:2008 | Safety of machinery. Secondary steelmaking. Machinery and equipment for treatment of liquid steel |
| UNE-EN 60079-10-1:2016 | Explosive atmospheres - Part 10-1: Classification of areas - Explosive gas atmospheres |
| 04/30115503 DC : DRAFT JUN 2004 | EN 14986 - DESIGN OF FANS WORKING IN POTENTIALLY EXPLOSIVE ATMOSPHERES |
| I.S. EN 14678-3:2013 | LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 3: REFUELLING INSTALLATIONS AT COMMERCIAL AND INDUSTRIAL PREMISES |
| CEI EN 60079-20-1 : 2010 | EXPLOSIVE ATMOSPHERES - PART 20-1: MATERIAL CHARACTERISTICS FOR GAS AND VAPOUR CLASSIFICATION - TEST METHODS AND DATA |
| BS EN 60079-19 : 2011 | EXPLOSIVE ATMOSPHERES - PART 19: EQUIPMENT REPAIR, OVERHAUL AND RECLAMATION |
| S.R. CEN/TR 16787:2014 | INDUSTRIAL GAS INSTALLATION - GUIDELINE |
| PD CLC/TR 60079-32-1:2015 | Explosive atmospheres Electrostatic hazards, guidance |
| UNE-EN 50050-3:2014 | Electrostatic hand-held spraying equipment - Safety requirements - Part 3: Hand-held spraying equipment for ignitable flock |
| 17/30365866 DC : 0 | BS EN 1127-1 - EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 1: BASIC CONCEPTS AND METHODOLOGY |
| EN 60079-19:2011/A1:2015 | EXPLOSIVE ATMOSPHERES - PART 19: EQUIPMENT REPAIR, OVERHAUL AND RECLAMATION (IEC 60079-19:2010) |
| EN 13617-1:2012 | Petrol filling stations - Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units |
| I.S. EN 12954:2001 | CATHODIC PROTECTION OF BURIED OR IMMERSED METALLIC STRUCTURES - GENERAL PRINCIPLES AND APPLICATION FOR PIPELINES |
| DIN EN 13355:2010-06 | COATING PLANTS - COMBINED BOOTHS - SAFETY REQUIREMENTS |
| DIN EN 1473:2016-10 | Installation and equipment for liquefied natural gas - Design of onshore installations |
| BS EN 1755:2015 | Industrial Trucks. Safety requirements and verification. Supplementary requirements for operation in potentially explosive atmospheres |
| UNE-EN 1127-1:2012 | Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology |
| BS EN 60079-18 : 2015 | EXPLOSIVE ATMOSPHERES - PART 18: EQUIPMENT PROTECTION BY ENCAPSULATION 'M' |
| BS EN 12921-1 : 2005 | MACHINES FOR SURFACE CLEANING AND PRE-TREATMENT OF INDUSTRIAL ITEMS USING LIQUIDS OR VAPOURS - PART 1: COMMON SAFETY REQUIREMENTS |
| EN 60079-26:2015 | Explosive atmospheres - Part 26: Equipment with Equipment Protection Level (EPL) Ga |
| EN 12753:2005+A1:2010 | Thermal cleaning systems for exhaust gas from surface treatment equipment - Safety requirements |
| EN 60079-25:2010/AC:2013 | EXPLOSIVE ATMOSPHERES - PART 25: INTRINSICALLY SAFE ELECTRICAL SYSTEMS (IEC 60079-25:2010) |
| EN 61158-2:2014 | Industrial communication networks - Fieldbus specifications - Part 2: Physical layer specification and service definition |
| DIN EN 12312-5:2009-08 | Aircraft ground support equipment - Specific requirements - Part 5: Aircraft fuelling equipment (includes Amendment A1:2009) |
| EN 1010-1:2004+A1:2010 | Safety of machinery - Safety requirements for the design and construction of printing and paper converting machines - Part 1: Common requirements |
| EN 50176:2009 | Stationary electrostatic application equipment for ignitable liquid coating material - Safety requirements |
| EN 50177:2009/A1:2012 | STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE COATING POWDERS - SAFETY REQUIREMENTS |
| EN 12779:2015 | Safety of woodworking machines - Chip and dust extraction systems with fixed installation - Safety requirements |
| EN 61241-17:2005 | Electrical apparatus for use in the presence of combustible dust - Part 17: Inspection and maintenance of electrical installations in hazardous areas (other than mines) |
| EN 12954 : 2001 | CATHODIC PROTECTION OF BURIED OR IMMERSED METALLIC STRUCTURES - GENERAL PRINCIPLES AND APPLICATION FOR PIPELINES |
| EN 12921-1:2005+A1:2010 | Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours - Part 1: Common safety requirements |
| EN 12215:2004+A1:2009 | Coating plants - Spray booths for application of organic liquid coating materials - Safety requirements |
| EN 13355:2004+A1:2009 | Coating plants - Combined booths - Safety requirements |
| EN 60079-27:2008 | Explosive atmospheres - Part 27: Fieldbus intrinsically safe concept (FISCO) |
| EN 50050-3:2013 | Electrostatic hand-held spraying equipment - Safety requirements - Part 3: Hand-held spraying equipment for ignitable flock |
| EN 12186:2014 | Gas infrastructure - Gas pressure regulating stations for transmission and distribution - Functional requirements |
| EN 62086-2:2005 | Electrical apparatus for explosive gas atmospheres - Electrical resistance trace heating - Part 2: Application guide for design, installation and maintenance |
| BS EN 16299:2013 | Cathodic protection of external surfaces of above ground storage tankbases in contact with soil or foundations |
| I.S. EN 13616-2:2016 | OVERFILL PREVENTION DEVICES FOR STATIC TANKS FOR LIQUID FUELS - PART 2: OVERFILL PREVENTION DEVICES WITHOUT A CLOSURE DEVICE |
| I.S. EN 45510-2-9:2008 | GUIDE FOR PROCUREMENT OF POWER STATION EQUIPMENT - PART 2-9: ELECTRICAL EQUIPMENT - CABLING SYSTEMS |
| BS EN 60079-26:2015 | Explosive atmospheres Equipment with Equipment Protection Level (EPL) Ga |
| 13/30280729 DC : 0 | BS EN 12186 - GAS INFRASTRUCTURE - GAS PRESSURE REGULATING STATIONS FOR TRANSMISSION AND DISTRIBUTION - FUNCTIONAL REQUIREMENTS |
| 11/30248842 DC : 0 | BS EN 50050-1:2011 - ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 1: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE LIQUID COATING MATERIALS |
| DIN EN 15001-1:2011-02 | Gas infrastructure - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 1: Detailed functional requirements for design, materials, construction, inspection and testing |
| BS EN 60079-29-2:2015 | Explosive atmospheres Gas detectors. Selection, installation, use and maintenance of detectors for flammable gases and oxygen |
| CEN/TR 16787:2014 | Industrial Gas Installation - Guideline |
| BS EN 62086-2:2005 | Electrical apparatus for explosive gas atmospheres. Electrical resistance trace heating Application guide for design, installation and maintenance |
| 09/30202029 DC : 0 | BS EN 13852-1 - CRANES - OFFSHORE CRANES - PART 1: GENERAL-PURPOSE OFFSHORE CRANES |
| I.S. EN 60079-27:2008 | EXPLOSIVE ATMOSPHERES - PART 27: FIELDBUS INTRINSICALLY SAFE CONCEPT (FISCO) |
| CEN/TR 15339-6:2014 | Thermal spraying - Safety requirements for thermal spraying equipment - Part 6: Spray booth, Handling system, Dust collection, Exhaust system, Filter |
| BS EN 60079-27:2008 | Explosive atmospheres Fieldbus intrinsically safe concept (FISCO) |
| BS EN 14678-3:2013 | LPG equipment and accessories. Construction and performance of LPG equipment for automotive filling stations Refuelling installations at commercial and industrial premises |
| 11/30235009 DC : 0 | BS EN 13852-1 - CRANES - OFFSHORE CRANES - PART 1: GENERAL PURPOSE OFFSHORE CRANES |
| BS EN 50223:2015 | Stationary electrostatic application equipment for ignitable flock material. Safety requirements |
| BS EN 15268:2008 | Petrol filling stations. Safety requirements for the construction of submersible pump assemblies |
| CEI EN 50176 : 2010 | STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE LIQUID COATING MATERIAL - SAFETY REQUIREMENTS |
| I.S. EN 50628:2016 | ERECTION OF ELECTRICAL INSTALLATIONS IN UNDERGROUND MINES |
| PREN 12186 : DRAFT 2013 | GAS INFRASTRUCTURE - GAS PRESSURE REGULATING STATIONS FOR TRANSMISSION AND DISTRIBUTION - FUNCTIONAL REQUIREMENTS |
| EN 50174-2 : 2009 AMD 2 2014 | INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 2: INSTALLATION PLANNING AND PRACTICES INSIDE BUILDINGS |
| PREN 14986 : DRAFT 2014 | DESIGN OF FANS WORKING IN POTENTIALLY EXPLOSIVE ATMOSPHERES |
| I.S. EN ISO 18081:2016 | NON-DESTRUCTIVE TESTING - ACOUSTIC EMISSION TESTING (AT) - LEAK DETECTION BY MEANS OF ACOUSTIC EMISSION (ISO 18081:2016) |
| I.S. EN 50176:2009 | STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE LIQUID COATING MATERIAL - SAFETY REQUIREMENTS |
| I.S. EN 1127-1:2011 | EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 1: BASIC CONCEPTS AND METHODOLOGY |
| I.S. EN 1012-3:2013 | COMPRESSORS AND VACUUM PUMPS - SAFETY REQUIREMENTS - PART 3: PROCESS COMPRESSORS |
| UNI EN 15268 : 2009 | PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP ASSEMBLIES |
| CEI EN 60079-25 : 2012 | EXPLOSIVE ATMOSPHERES - PART 25: INTRINSICALLY SAFE ELECTRICAL SYSTEMS |
| CEI EN 50174-3 : 2014 | INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 3: INSTALLATION PLANNING AND PRACTICES OUTSIDE BUILDINGS |
| I.S. EN 13616-1:2016 | OVERFILL PREVENTION DEVICES FOR STATIC TANKS FOR LIQUID FUELS -PART 1: OVERFILL PREVENTION DEVICES WITH CLOSURE DEVICE |
| I.S. EN 50177:2009 | STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE COATING POWDERS - SAFETY REQUIREMENTS |
| CEI 20-59 : 1999 | MULTICORE AND MULTIPAIR CABLE FOR INSTALLATION ABOVE AND BELOW GROUND |
| CEI EN 62305-3 : 2013 | PROTECTION AGAINST LIGHTNING - PART 3: PHYSICAL DAMAGE TO STRUCTURES AND LIFE HAZARD |
| EN 50310:2016 | Telecommunications bonding networks for buildings and other structures |
| I.S. EN 62086-2:2005 | ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - ELECTRICAL RESISTANCE TRACE HEATING - PART 2: APPLICATION GUIDE FOR DESIGN, INSTALLATION AND MAINTENANCE |
| I.S. EN 15268:2008 | PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP ASSEMBLIES |
| DIN EN 1010-1:2011-06 | Safety of machinery - Safety requirements for the design and construction of printing and paper converting machines - Part 1: Common requirements (includes Amendment A1:2010) |
| DIN EN 14197-3:2005-09 | Cryogenic vessels - Static non vacuum insulated vessels - Part 3: Operational requirements |
| DIN EN 12215:2010-06 | COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC LIQUID COATING MATERIALS - SAFETY REQUIREMENTS |
| DIN EN 12981:2010-06 | COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC POWDER COATING MATERIAL - SAFETY REQUIREMENTS |
| DIN EN 13617-1:2012-08 | Petrol filling stations - Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units |
| BS EN 13355 : 2004 | COATING PLANTS - COMBINED BOOTHS - SAFETY REQUIREMENTS |
| UNE-EN 12186:2015 | Gas infrastructure - Gas pressure regulating stations for transmission and distribution - Functional requirements |
| BS EN 12981 : 2005 | COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC POWDER COATING MATERIAL - SAFETY REQUIREMENTS |
| UNE-EN 50310:2016 | Telecommunications bonding networks for buildings and other structures |
| I.S. EN 14678-1:2013 | LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 1: DISPENSERS |
| I.S. EN 13952:2017 | LPG EQUIPMENT AND ACCESSORIES - FILLING OPERATIONS FOR LPG CYLINDERS |
| DIN EN 1755:2016-02 | Industrial Trucks - Safety requirements and verification - Supplementary requirements for operation in potentially explosive atmospheres |
| DIN EN 1473:1997-11 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS |
| I.S. EN 12215:2004 | COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC LIQUID COATING MATERIALS - SAFETY REQUIREMENTS |
| DIN EN 1127-1:2011-10 | EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 1: BASIC CONCEPTS AND METHODOLOGY |
| DIN EN 1776:2016-05 | GAS INFRASTRUCTURE - GAS MEASURING SYSTEMS - FUNCTIONAL REQUIREMENTS |
| I.S. EN 13852-1:2013 | CRANES - OFFSHORE CRANES - PART 1: GENERAL - PURPOSE OFFSHORE CRANES |
| I.S. EN 12981:2005 | COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC POWDER COATING MATERIAL - SAFETY REQUIREMENTS |
| DIN EN 13852-2:2005-03 | Cranes - Offshore cranes - Part 2: Floating cranes |
| I.S. EN 1612-2:2000 | PLASTICS AND RUBBER MACHINES - REACTION MOULDING MACHINES - PART 2: SAFETY REQUIREMENTS FOR REACTION MOULDING PLANT |
| I.S. EN 1755:2015 | INDUSTRIAL TRUCKS - SAFETY REQUIREMENTS AND VERIFICATION - SUPPLEMENTARY REQUIREMENTS FOR OPERATION IN POTENTIALLY EXPLOSIVE ATMOSPHERES |
| I.S. EN 13355:2005 | COATING PLANTS - COMBINED BOOTHS - SAFETY REQUIREMENTS |
| EN 60079-10-1:2015 | Explosive atmospheres - Part 10-1: Classification of areas - Explosive gas atmospheres |
| I.S. EN 12186:2014 | GAS INFRASTRUCTURE - GAS PRESSURE REGULATING STATIONS FOR TRANSMISSION AND DISTRIBUTION - FUNCTIONAL REQUIREMENTS |
| I.S. EN 12312-5:2005 | AIRCRAFT GROUND SUPPORT EQUIPMENT - SPECIFIC REQUIREMENTS - PART 5: AIRCRAFT FUELLING EQUIPMENT |
| I.S. EN 12779:2015 | SAFETY OF WOODWORKING MACHINES - CHIP AND DUST EXTRACTION SYSTEMS WITH FIXED INSTALLATION - SAFETY RELATED PERFORMANCES AND SAFETY REQUIREMENTS |
| I.S. EN 13617-1:2012 | PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| I.S. EN 1473:2016 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS |
| EN 12312-5:2005+A1:2009 | Aircraft ground support equipment - Specific requirements - Part 5: Aircraft fuelling equipment |
| I.S. EN 1010-1:2005 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PRINTING AND PAPER CONVERTING MACHINES - PART 1: COMMON REQUIREMENTS |
| I.S. EN 12753:2005 | THERMAL CLEANING SYSTEMS FOR EXHAUST GAS FROM SURFACE TREATMENT EQUIPMENT - SAFETY REQUIREMENTS |
| I.S. EN 1776:2015 | GAS INFRASTRUCTURE - GAS MEASURING SYSTEMS - FUNCTIONAL REQUIREMENTS |
| I.S. EN 14986:2017 | DESIGN OF FANS WORKING IN POTENTIALLY EXPLOSIVE ATMOSPHERES |
| I.S. EN 12921-1:2005 | MACHINES FOR SURFACE CLEANING AND PRE-TREATMENT OF INDUSTRIAL ITEMS USING LIQUIDS OR VAPOURS - PART 1: COMMON SAFETY REQUIREMENTS |
| VDE 0165-10 : 1999 | ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - PART 17: INSPECTION AND MAINTENANCE OF ELECTRICAL INSTALLATIONS IN HAZARDOUS AREAS (OTHER THAN MINES) |
| VDI 2260:2003-10 | Technical warranty for gas cleaning equipment - Particulate and gaseous matter |
| VDI 2263 Blatt 8.1:2011-03 | Dust fires and dust explosions - Hazards - assessment - protective measures - Fire and explosion protection on elevators - Examples |
| VDI/VDE/DGQ/DKD 2622 Blatt 20:2013-12 | Calibration of measuring equipment for electrical quantities - Direct-voltage measuring amplifiers |
| VDI 2263 Blatt 5.1:2014-10 | Dust fires and dust explosions - Hazards, assessment, protective measures - Explosion protection in fluid bed dryers - Hints and examples of operation |
| VDI 2330 Blatt 1:2013-09 | Screw conveyors for bulk materials - General characterisation |
| UNE-EN 13616-1:2016 | Overfill prevention devices for static tanks for liquid fuels - Part 1: Overfill prevention devices with closure device |
| CEI EN 50050-2 : 2014 | ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 2: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE COATING POWDER |
| I.S. EN 15001-2:2008 | GAS INFRASTRUCTURE - GAS INSTALLATION PIPEWORK WITH AN OPERATING PRESSURE GREATER THAN 0,5 BAR FOR INDUSTRIAL INSTALLATIONS AND GREATER THAN 5 BAR FOR INDUSTRIAL AND NON INDUSTRIAL INSTALLATIONS - PART 2: DETAILED FUNCTIONAL REQUIREMENTS FOR COMMISSIONING, OPERATION AND MAINTENANCE |
| 15/30320786 DC : 0 | BS EN 13952 - LPG EQUIPMENT AND ACCESSORIES - FILLING PROCEDURES FOR LPG CYLINDERS |
| 13/30257895 DC : 0 | BS EN 1755 - SAFETY OF INDUSTRIAL TRUCKS - OPERATION IN POTENTIALLY EXPLOSIVE ATMOSPHERES - USE IN FLAMMABLE GAS, VAPOUR, MIST AND DUST |
| BS EN 50050-2:2013 | Electrostatic hand-held spraying equipment. Safety requirements Hand-held spraying equipment for ignitable coating powder |
| PREN 1473 : DRAFT 2018 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS |
| PREN 13617-1 : DRAFT 2010 | PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| 11/30248021 DC : 0 | AEROSPACE SERIES - COPPER ALLOY CUBE 1.9 - SOLUTION TREATED, COLD WORKED TO [1/2] HARD AND PRECIPITATION TREATED - BAR - 5 MM <= A OR D <= 190 MM - R[M] >= 1220 MPA |
| 15/30296744 DC : 0 | BS EN 12013 - PLASTICS AND RUBBER MACHINES - INTERNAL MIXERS - SAFETY REQUIREMENTS |
| DIN EN 14677:2008-11 | SAFETY OF MACHINERY - SECONDARY STEEL MAKING - MACHINERY AND EQUIPMENT FOR TREATMENT OF LIQUID STEEL |
| 12/30260552 DC : 0 | BS EN 50174-3:201X - INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 3: INSTALLATION PLANNING AND PRACTICES OUTSIDE BUILDINGS |
| BS EN 60079-10-2:2015 | Explosive atmospheres Classification of areas. Explosive dust atmospheres |
| 10/30219405 DC : 0 | BS EN 13617-1 - PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| PD CLC/TS 62603-1:2014 | Industrial process control systems. Guideline for evaluating process control systems Specifications |
| 10/30230365 DC : 0 | BS EN 50050-2 - ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT SAFETY REQUIREMENTS - PART 2: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE COATING POWDER |
| EN 1473:2016 | Installation and equipment for liquefied natural gas - Design of onshore installations |
| CEI EN 60079-17 : 2015 | EXPLOSIVE ATMOSPHERES - PART 17: ELECTRICAL INSTALLATIONS INSPECTION AND MAINTENANCE |
| CEI EN 50050-1 : 2014 | ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 1: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE LIQUID COATING MATERIALS |
| BS EN 50050-3:2013 | Electrostatic hand-held spraying equipment. Safety requirements Hand-held spraying equipment for ignitable flock |
| UNE-EN 50176:2010 | Stationary electrostatic application equipment for ignitable liquid coating material - Safety requirements |
| DIN EN 15268 E : 2008 | PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP ASSEMBLIES |
| 05/30128234 DC : DRAFT FEB 2005 | EN 1473 - INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS |
| NF EN 15001-1 : 2009 | GAS INFRASTRUCTURE - GAS INSTALLATION PIPEWORK WITH AN OPERATING PRESSURE GREATER THAN 0,5 BAR FOR INDUSTRIAL INSTALLATIONS AND GREATER THAN 5 BAR FOR INDUSTRIAL AND NON-INDUSTRIAL INSTALLATIONS - PART 1: DETAILED FUNCTIONAL REQUIREMENTS FOR DESIGN, MATERIALS, CONSTRUCTION, INSPECTION AND TESTING |
| 03/303438 DC : DRAFT MAR 2003 | BS 7540-2:2004 - GUIDE TO USE FOR CABLES WITH A RATED VOLTAGE NOT EXCEEDING 450/750 V - PART 2: HARMONIZED CABLE TYPES FROM HD 21 AND HD 22 |
| 07/30152812 DC : DRAFT AUG 2007 | BS EN 50174-2 - INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 2: INSTALLATION PLANNING AND PRACTICES INSIDE BUILDINGS |
| BS EN 1012-3:2013 | Compressors and vacuum pumps. Safety requirements Process compressors |
| 14/30294092 DC : 0 | BS EN 14986 - DESIGN OF FANS WORKING IN POTENTIALLY EXPLOSIVE ATMOSPHERES |
| I.S. EN 60079-10-1:2015 | EXPLOSIVE ATMOSPHERES - PART 10-1: CLASSIFICATION OF AREAS - EXPLOSIVE GAS ATMOSPHERES |
| PREN 12779 : DRAFT 2014 | SAFETY OF WOODWORKING MACHINES - CHIPS AND DUST EXTRACTION SYSTEMS WITH FIXED INSTALLATIONS - SAFETY REQUIREMENTS |
| I.S. EN 61158-2:2014 | INDUSTRIAL COMMUNICATION NETWORKS - FIELDBUS SPECIFICATIONS - PART 2: PHYSICAL LAYER SPECIFICATION AND SERVICE DEFINITION |
| I.S. EN 50050-2:2013 | ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 2: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE COATING POWDER |
| I.S. EN 62305-3:2011 | PROTECTION AGAINST LIGHTNING - PART 3: PHYSICAL DAMAGE TO STRUCTURES AND LIFE HAZARD |
| I.S. EN 60079-17:2014 | EXPLOSIVE ATMOSPHERES - PART 17: ELECTRICAL INSTALLATIONS INSPECTION AND MAINTENANCE |
| UNI EN 15001-2 : 2009 | GAS INFRASTRUCTURE - GAS INSTALLATION PIPEWORK WITH AN OPERATING PRESSURE GREATER THAN 0,5 BAR FOR INDUSTRIAL INSTALLATIONS AND GREATER THAN 5 BAR FOR INDUSTRIAL AND NON-INDUSTRIAL INSTALLATIONS - PART 2: DETAILED FUNCTIONAL REQUIREMENTS FOR COMMISSIONING, OPERATION AND MAINTENANCE |
| I.S. EN 50174-3:2013 | INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 3: INSTALLATION PLANNING AND PRACTICES OUTSIDE BUILDINGS |
| UNE-EN 62305-3:2011 | Protection against lightning -- Part 3: Physical damages to structures and life hazard |
| I.S. EN 50310:2016 | TELECOMMUNICATIONS BONDING NETWORKS FOR BUILDINGS AND OTHER STRUCTURES |
| UNI EN 14678-3 : 2013 | LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 3: REFUELLING INSTALLATIONS AT COMMERCIAL AND INDUSTRIAL PREMISES |
| PREN 50174-3 : DRAFT 2012 | INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 3: INSTALLATION PLANNING AND PRACTICES OUTSIDE BUILDINGS |
| BS EN 1127-1:2019 | Explosive atmospheres. Explosion prevention and protection Basic concepts and methodology |
| UNI EN 16299 : 2013 | CATHODIC PROTECTION OF EXTERNAL SURFACES OF ABOVE GROUND STORAGE TANK BASES IN CONTACT WITH SOIL OR FOUNDATIONS |
| DIN EN 12921-1:2011-02 | Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours - Part 1: Common safety requirements (includes Amendment A1:2010) |
| DIN EN 12186:2014-12 | GAS INFRASTRUCTURE - GAS PRESSURE REGULATING STATIONS FOR TRANSMISSION AND DISTRIBUTION - FUNCTIONAL REQUIREMENTS |
| DIN EN 12312-5 E : 2009 | AIRCRAFT GROUND SUPPORT EQUIPMENT - SPECIFIC REQUIREMENTS - PART 5: AIRCRAFT FUELLING EQUIPMENT |
| DIN EN 12779:2016-03 | Safety of woodworking machines - Chip and dust extraction systems with fixed installation - Safety requirements |
| DIN EN 13952:2015-09 (Draft) | LPG EQUIPMENT AND ACCESSORIES - FILLING OPERATIONS FOR LPG CYLINDERS |
| UNE-EN 15001-1:2010 | Gas Infrastructure - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 1: Detailed functional requirements for design, materials, construction, inspection and testing |
| UNE-EN 1755:2016 | Industrial Trucks - Safety requirements and verification - Supplementary requirements for operation in potentially explosive atmospheres |
| BS EN 1010-1 : 2004 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PRINTING AND PAPER CONVERTING MACHINES - PART 1: COMMON REQUIREMENTS |
| BS EN 1473:2016 | Installation and equipment for liquefied natural gas. Design of onshore installations |
| BS EN 12312-5 : 2005 | AIRCRAFT GROUND SUPPORT EQUIPMENT - SPECIFIC REQUIREMENTS - PART 5: AIRCRAFT FUELLING EQUIPMENT |
| BS EN 12215 : 2004 | COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC LIQUID COATING MATERIALS - SAFETY REQUIREMENTS |
| UNE-EN 14678-1:2013 | LPG equipment and accessories - Construction and performance of LPG equipment for automotive filling stations - Part 1: Dispensers |
| BS EN 12753 : 2005 | THERMAL CLEANING SYSTEMS FOR EXHAUST GAS FROM SURFACE TREATMENT EQUIPMENT - SAFETY REQUIREMENTS |
| EEMUA 207 : 2009 | DOUBLE CONCRETE TANKS FOR LIQUEFIED GAS - GUIDE TO DESIGN, CONSTRUCTION AND OPERATION |
| UNI EN 13617-1 : 2012 | PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| EN 14678-1:2013 | LPG equipment and accessories - Construction and performance of LPG equipment for automotive filling stations - Part 1: Dispensers |
| EN 16299:2013 | Cathodic protection of external surfaces of above ground storage tank bases in contact with soil or foundations |
| UNI EN 12921-1 : 2010 | MACHINES FOR SURFACE CLEANING AND PRE- TREATMENT OF INDUSTRIAL ITEMS USING LIQUIDS OR VAPOURS - PART 1: COMMON SAFETY REQUIREMENTS |
| UNI EN 1612-2 : 2008 | PLASTICS AND RUBBER MACHINES - REACTION MOULDING MACHINES - PART 2: SAFETY REQUIREMENTS FOR REACTION MOULDING PLANT |
| EN 50281-1-2 : 98 AMD 1 2002 | ELECTRICAL APPARATUS FOR USE IN THE PRESENCE OF COMBUSTIBLE DUST - PART 1-2: ELECTRICAL APPARATUS PROTECTED BY ENCLOSURES - SELECTION, INSTALLATION AND MAINTENANCE |
| UNI EN 14677 : 2008 | SAFETY OF MACHINERY - SECONDARY STEELMAKING - MACHINERY AND EQUIPMENT FOR TREATMENT OF LIQUID STEEL |
| UNI EN 1010-1 : 2011 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PRINTING AND PAPER CONVERTING MACHINES - PART 1: COMMON REQUIREMENTS |
| UNI EN 12186 : 2014 | GAS INFRASTRUCTURE - GAS PRESSURE REGULATING STATIONS FOR TRANSMISSION AND DISTRIBUTION - FUNCTIONAL REQUIREMENTS |
| UNI EN 12981 : 2009 | COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC POWDER COATING MATERIAL - SAFETY REQUIREMENTS |
| UNI EN 1012-3 : 2014 | COMPRESSORS AND VACUUM PUMPS - SAFETY REQUIREMENTS - PART 3: PROCESS COMPRESSORS |
| UNI EN 15001-1 : 2009 | GAS INFRASTRUCTURE - GAS INSTALLATION PIPEWORK WITH AN OPERATING PRESSURE GREATER THAN 0,5 BAR FOR INDUSTRIAL INSTALLATIONS AND GREATER THAN 5 BAR FOR INDUSTRIAL AND NON-INDUSTRIAL INSTALLATIONS - PART 1: DETAILED FUNCTIONAL REQUIREMENTS FOR DESIGN, MATERIALS, CONSTRUCTION, INSPECTION AND TESTING |
| UNI EN 13852-1 : 2013 | CRANES - OFFSHORE CRANES - PART 1: GENERAL-PURPOSE OFFSHORE CRANES |
| UNI EN 12753 : 2010 | THERMAL CLEANING SYSTEMS FOR EXHAUST GAS FROM SURFACE TREATMENT EQUIPMENT - SAFETY REQUIREMENTS |
| UNI EN 14678-1 : 2013 | LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 1: DISPENSERS |
| UNI EN 13355 : 2009 | COATING PLANTS - COMBINED BOOTHS - SAFETY REQUIREMENTS |
| UNI EN 12215 : 2010 | COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC LIQUID COATING MATERIALS - SAFETY REQUIREMENTS |
| EN 45510-2-9:2008 | GUIDE FOR PROCUREMENT OF POWER STATION EQUIPMENT - PART 2-9: ELECTRICAL EQUIPMENT - CABLING SYSTEMS |
| UNE-EN 50223:2016 | Stationary electrostatic application equipment for ignitable flock material - Safety requirements |
| BS EN 50176:2009 | Stationary electrostatic application equipment for ignitable liquid coating material. Safety requirements |
| BS EN ISO 18081:2016 | Non-destructive testing. Acoustic emission testing (AT). Leak detection by means of acoustic emission |
| I.S. EN 50050-3:2013 | ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 3: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE FLOCK |
| PD CEN/TR 16787:2014 | Industrial Gas Installation. Guideline |
| PREN 15001-2 : DRAFT 2017 | GAS SUPPLY SYSTEMS - GAS INSTALLATION PIPEWORK WITH AN OPERATING PRESSURE GREATER THAN 0,5 BAR FOR INDUSTRIAL INSTALLATIONS AND GREATER THAN 5 BAR FOR INDUSTRIAL AND NON-INDUSTRIAL INSTALLATIONS - PART 2: DETAILED FUNCTIONAL REQUIREMENTS FOR COMMISSIONING, OPERATION AND MAINTENANCE |
| PREN 12013 : DRAFT 2015 | PLASTICS AND RUBBER MACHINES - INTERNAL MIXERS - SAFETY REQUIREMENTS |
| DIN EN 14678-3:2013-03 | LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 3: REFUELLING INSTALLATIONS AT COMMERCIAL AND INDUSTRIAL PREMISES |
| IEC TR 61831:2011 | On-line analyser systems - Guide to design and installation |
| PREN 14678-1 : DRAFT 2010 | LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 1: DISPENSERS |
| PREN 50050-3 : DRAFT 2011 | ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 3: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE FLOCK |
| PREN 50050-2 : DRAFT 2011 | ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 2: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE COATING POWDER |
| I.S. EN 16299:2013 | CATHODIC PROTECTION OF EXTERNAL SURFACES OF ABOVE GROUND STORAGE TANK BASES IN CONTACT WITH SOIL OR FOUNDATIONS |
| 14/30316181 DC : 0 | BS EN 50628 - ERECTION OF ELECTRICAL INSTALLATIONS IN UNDERGROUND MINES |
| 11/30248845 DC : 0 | BS EN 50050-2:2011 - ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 2: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE COATING POWDER |
| PREN 1755 : DRAFT 2013 | SAFETY OF INDUSTRIAL TRUCKS - OPERATION IN POTENTIALLY EXPLOSIVE ATMOSPHERES - USE IN FLAMMABLE GAS, VAPOUR, MIST AND DUST |
| 14/30292850 DC : 0 | BS EN 12779 - SAFETY OF WOODWORKING MACHINES - CHIPS AND DUST EXTRACTION SYSTEMS WITH FIXED INSTALLATIONS - SAFETY REQUIREMENTS |
| BS EN 60079-20-1:2010 | Explosive atmospheres Material characteristics for gas and vapour classification. Test methods and data |
| 04/30116801 DC : 0 | EN 15001-2 - GAS SUPPLY SYSTEMS - GAS INSTALLATION PIPEWORK WITH AN OPERATING PRESSURE GREATER THAN 0.5 BAR FOR INDUSTRIAL, COMMERCIAL AND NON-DOMESTIC INSTALLATIONS - PART 2: DETAILED FUNCTIONAL REQUIREMENTS FOR COMMISSIONING, OPERATION AND MAINTENANCE |
| DIN EN 15268:2008-11 | PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP |
| BS EN 13616-1:2016 | Overfill prevention devices for static tanks for liquid fuels Overfill prevention devices with closure device |
| BS EN 60079-10-1:2015 | Explosive atmospheres Classification of areas. Explosive gas atmospheres |
| UNE-EN 60079-25:2017 | Explosive atmospheres -- Part 25: Intrinsically safe electrical systems |
| UNI EN 1127-1 : 2011 | EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 1: BASIC CONCEPTS AND METHODOLOGY |
| BS EN 50177 : 2009 | STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE COATING POWDERS - SAFETY REQUIREMENTS |
| UNE-EN 16299:2013 | Cathodic protection of external surfaces of above ground storage tank bases in contact with soil or foundations |
| I.S. EN 61241-17:2005 | ELECTRICAL APPARATUS FOR USE IN THE PRESENCE OF COMBUSTIBLE DUST - PART 17: INSPECTION AND MAINTENANCE OF ELECTRICAL INSTALLATIONS IN HAZARDOUS AREAS (OTHER THAN MINES) |
| EN 50174-3:2013/A1:2017 | INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 3: INSTALLATION PLANNING AND PRACTICES OUTSIDE BUILDINGS |
| I.S. EN 50174-2:2009 | INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 2: INSTALLATION PLANNING AND PRACTICES INSIDE BUILDINGS |
| PREN 13852-1 : DRAFT 2011 | CRANES - OFFSHORE CRANES - PART 1: GENERAL PURPOSE OFFSHORE CRANES |
| PREN 50628 : DRAFT 2014 | ERECTION OF ELECTRICAL INSTALLATIONS IN UNDERGROUND MINES |
| I.S. EN 15001-1:2009 | GAS INFRASTRUCTURE - GAS INSTALLATION PIPEWORK WITH AN OPERATING PRESSURE GREATER THAN 0,5 BAR FOR INDUSTRIAL INSTALLATIONS AND GREATER THAN 5 BAR FOR INDUSTRIAL AND NON-INDUSTRIAL INSTALLATIONS - PART 1: DETAILED FUNCTIONAL REQUIREMENTS FOR DESIGN, MATERIALS, CONSTRUCTION, INSPECTION AND TESTING |
| S.R. CEN/TR 15339-6:2014 | THERMAL SPRAYING - SAFETY REQUIREMENTS FOR THERMAL SPRAYING EQUIPMENT - PART 6: SPRAY BOOTH, HANDLING SYSTEM, DUST COLLECTION, EXHAUST SYSTEM, FILTER |
| UNE-EN 50050-1:2014 | Electrostatic hand-held spraying equipment - Safety requirements - Part 1: Hand-held spraying equipment for ignitable liquid coating materials |
| DIN EN 12753:2011-02 | Thermal cleaning systems for exhaust gas from surface treatment equipment - Safety requirements (includes Amendment A1:2010) |
| DIN EN 61158-2:2015-02 | INDUSTRIAL COMMUNICATION NETWORKS - FIELDBUS SPECIFICATIONS - PART 2: PHYSICAL LAYER SPECIFICATION AND SERVICE DEFINITION (IEC 61158-2:2014) |
| DIN EN 13852-1:2014-01 | Cranes - Offshore cranes - Part 1: General-purpose offshore cranes |
| BS EN 1612-2 : 2000 | PLASTICS AND RUBBER MACHINES - REACTION MOULDING MACHINES - PART 2: SAFETY REQUIREMENTS FOR REACTION MOULDING PLANT |
| BS EN 61158-2:2014 | Industrial communication networks. Fieldbus specifications Physical layer specification and service definition |
| BS EN 12186:2014 | Gas infrastructure. Gas pressure regulating stations for transmission and distribution. Functional requirements |
| 05/30133440 DC : DRAFT MAY 2005 | EN 50310 ED 2 - APPLICATION OF EQUIPOTENTIAL BONDING AND EARTHING IN BUILDINGS WITH INFORMATION TECHNOLOGY EQUIPMENT |
| BS EN 14986:2007 | Design of fans working in potentially explosive atmospheres |
| UNE-EN 1776:2017 | Gas infrastructure - Gas measuring systems - Functional requirements |
| BS EN 13617-1:2012 | Petrol filling stations Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units |
| BS EN 12954:2001 | Cathodic protection of buried or immersed metallic structures. General principles and application for pipelines |
| 17/30361391 DC : 0 | BS EN 50174-2 - INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 2: INSTALLATION PLANNING AND PRACTICES INSIDE BUILDINGS |
| BS EN 12779:2015 | Safety of woodworking machines. Chip and dust extraction systems with fixed installation. Safety requirements |
| BS EN 1776:2015 | Gas infrastructure. Gas measuring systems. Functional requirements |
| UNE-EN 14986:2017 | Design of fans working in potentially explosive atmospheres |
| UNE-EN 13617-1:2012 | Petrol filling stations - Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units |
| ISO 18081:2016 | Non-destructive testing Acoustic emission testing (AT) Leak detection by means of acoustic emission |
| BS EN 50310:2016 | Telecommunications bonding networks for buildings and other structures |
| UNE-EN 13852-1:2014 | Cranes - Offshore cranes - Part 1: General-purpose offshore cranes |
| EN 45510-2-9 : 2008 | GUIDE FOR PROCUREMENT OF POWER STATION EQUIPMENT - PART 2-9: ELECTRICAL EQUIPMENT - CABLING SYSTEMS |
| EN ISO 18081:2016 | Non-destructive testing - Acoustic emission testing (AT) - Leak detection by means of acoustic emission (ISO 18081:2016) |
| EN 14986:2017 | Design of fans working in potentially explosive atmospheres |
| EI MODEL CODE SAFE PRACTICE PT1 : 2010 | THE SELECTION, INSTALLATION, INSPECTION, AND MAINTENANCE OF ELECTRICAL AND NON ELECTRICAL APPARATUS IN HAZARDOUS AREAS |
| EN 15001-1:2009 | Gas Infrastructure - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 1: Detailed functional requirements for design, materials, construction, inspection and testing |
| EN 1755:2015 | Industrial Trucks - Safety requirements and verification - Supplementary requirements for operation in potentially explosive atmospheres |
| EN 15001-2:2008 | Gas infrastructure - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 2: Detailed functional requirements for commissioning, operation and maintenance |
| EN 1612-2:2000+A1:2008 | Plastics and rubber machines - Reaction moulding machines - Part 2: Safety requirements for reaction moulding plant |
| EN 15268:2008 | Petrol filling stations - Safety requirements for the construction of submersible pump assemblies |
| EN 1776:2015 | Gas infrastructure - Gas measuring systems - Functional requirements |
| EI 1540 : 2014 | DESIGN, CONSTRUCTION, COMMISSIONING, MAINTENANCE AND TESTING OF AVIATION FUELLING FACILITIES |
| EN 13616-1:2016 | Overfill prevention devices for static tanks for liquid fuels - Part 1: Overfill prevention devices with closure device |
| EN 14197-3:2004/A1:2005 | CRYOGENIC VESSELS - STATIC NON-VACUUM INSULATED VESSELS - PART 3: OPERATIONAL REQUIREMENTS |
| EN 13952:2017 | LPG equipment and accessories - Filling operations for LPG cylinders |
| EN 13852-1:2013 | Cranes - Offshore cranes - Part 1: General-purpose offshore cranes |
| EN 14678-3:2013 | LPG equipment and accessories - Construction and performance of LPG equipment for automotive filling stations - Part 3: Refuelling installations at commercial and industrial premises |
| EN 14677:2008 | Safety of machinery - Secondary steelmaking - Machinery and equipment for treatment of liquid steel |
| EN 13852-2:2004 | Cranes - Offshore cranes - Part 2: Floating cranes |
| BS EN 13616-2:2016 | Overfill prevention devices for static tanks for liquid fuels Overfill prevention devices without a closure device |
| CEI 20-59 V1 : 2006 | MULTICORE AND MULTIPAIR CABLE FOR INSTALLATION ABOVE AND BELOW GROUND |
| I.S. EN 60079-25:2010 | EXPLOSIVE ATMOSPHERES - PART 25: INTRINSICALLY SAFE ELECTRICAL SYSTEMS (IEC 60079-25:2010 (EQV)) |
| EI TP PETROLEUM ROAD TANKER : 2010 | PETROLEUM ROAD TANKER DESIGN AND CONSTRUCTION |
| UNE-EN 50177:2010 | Stationary electrostatic application equipment for ignitable coating powders - Safety requirements |
| BS EN 60079-25:2010 | Explosive atmospheres Intrinsically safe electrical systems |
| PD IEC/TR 61831:2011 | On-line analyser systems. Guide to design and installation |
| BS EN 50050-1:2013 | Electrostatic hand-held spraying equipment. Safety requirements Hand-held spraying equipment for ignitable liquid coating materials |
| PD CEN/TR 15339-6:2014 | Thermal spraying. Safety requirements for thermal spraying equipment Spray booth, Handling system, Dust collection, Exhaust system, Filter |
| CEI EN 50050-3 : 2014 | ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 3: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE FLOCK |
| S.R. CLC/TS 62603-1:2014 | INDUSTRIAL PROCESS CONTROL SYSTEMS - GUIDELINE FOR EVALUATING PROCESS CONTROL SYSTEMS - PART 1: SPECIFICATIONS |
| I.S. EN 50050-1:2013 | ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 1: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE LIQUID COATING MATERIALS |
| BS EN 15001-1:2009 | Gas infrastructure. Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations Detailed functional requirements for design, materials, construction, inspection and testing |
| S.R. CLC/TR 60079-32-1:2015 | EXPLOSIVE ATMOSPHERES - PART 32-1: ELECTROSTATIC HAZARDS - GUIDANCE |
| UNE-EN 13616-2:2016 | Overfill prevention devices for static tanks for liquid fuels - Part 2: Overfill prevention devices without a closure device |
| UNE-EN 14678-3:2013 | LPG equipment and accessories - Construction and performance of LPG equipment for automotive filling stations - Part 3: Refuelling installations at commercial and industrial premises |
| 08/30186475 DC : 0 | BS EN 13617-1 AMD1 - PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| 05/30135286 DC : 0 | EN 15268 - PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION AND PERFORMANCE OF SUBMERSIBLE PUMP ASSEMBLIES |
| 14/30297213 DC : 0 | BS EN 1473 - INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS |
| DIN EN 14677 E : 2008 | SAFETY OF MACHINERY - SECONDARY STEELMAKING - MACHINERY AND EQUIPMENT FOR TREATMENT OF LIQUID STEEL |
| UNE-EN 60079-29-2:2016 | Explosive atmospheres - Part 29-2: Gas detectors - Selection, installation, use and maintenance of detectors for flammable gases and oxygen |
| I.S. EN 14677:2008 | SAFETY OF MACHINERY - SECONDARY STEELMAKING - MACHINERY AND EQUIPMENT FOR TREATMENT OF LIQUID STEEL |
| PREN 1127-2 : DRAFT 2012 | EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 2: BASIC CONCEPTS AND METHODOLOGY FOR MINING |
| EN 60079-18:2015/A1:2017 | EXPLOSIVE ATMOSPHERES - PART 18: EQUIPMENT PROTECTION BY ENCAPSULATION 'M' (IEC 60079-18:2014/A1:2017) |
| 18/30369304 DC : DRAFT APR 2018 | BS EN 1473 - INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS |
| UNE-EN 60079-20-1:2014 | Explosive atmospheres - Part 20-1: Material characteristics for gas and vapour classification - Test methods and data |
| BS EN 50174-3 : 2013 | INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 3: INSTALLATION PLANNING AND PRACTICES OUTSIDE BUILDINGS |
| BS EN 60079-0 : 2012 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS |
| UNE-EN 60079-19:2011 | Explosive atmospheres - Part 19: Equipment repair, overhaul and reclamation |
| BS EN 1127-1:2011 | Explosive atmospheres. Explosion prevention and protection Basic concepts and methodology |
| CLC/TR 60079-32-1:2015 | Explosive atmospheres - Part 32-1: Electrostatic Hazards - Guidance |
| I.S. EN 50223:2015 | STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE FLOCK MATERIAL - SAFETY REQUIREMENTS |
| NF EN 12312-5 : 2005 + A1 2010 | AIRCRAFT GROUND SUPPORT EQUIPMENT - SPECIFIC REQUIREMENTS - PART 5: AIRCRAFT FUELLING EQUIPMENT |
| DIN EN 14678-1:2013-06 | LPG equipment and accessories - Construction and performance of LPG equipment for automotive filling stations - Part 1: Dispensers |
| BS EN 13852-2:2004 | Cranes. Offshore cranes Floating cranes |
| UNE-EN 12779:2016 | Safety of woodworking machines - Chip and dust extraction systems with fixed installation - Safety requirements |
| BS EN 50174-2 : 2009 | INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 2: INSTALLATION PLANNING AND PRACTICES INSIDE BUILDINGS |
| BS EN 13952:2017 | LPG equipment and accessories. Filling operations for LPG cylinders |
| BS EN 45510-2-9:2008 | Guide for procurement of power station equipment Electrical equipment. Cabling systems |
| BS EN 14678-1:2013 | LPG equipment and accessories. Construction and performance of LPG equipment for automotive filling stations Dispensers |
| BS EN 50628:2016 | Erection of electrical installations in underground mines |
| 09/30205182 DC : 0 | BS EN 50310 - APPLICATION OF EQUIPOTENTIAL BONDING AND EARTHING IN BUILDINGS WITH INFORMATION TECHNOLOGY EQUIPMENT |
| BS EN 13852-1:2013 | Cranes. Offshore cranes General-purpose offshore cranes |
| EN 1012-3:2013 | Compressors and vacuum pumps - Safety requirements - Part 3: Process compressors |
| EN 60079-0:2012/A11:2013 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED) |
| EN 12981:2005+A1:2009 | Coating plants - Spray booths for application of organic powder coating material - Safety requirements |
| EN 60079-17:2014 | Explosive atmospheres - Part 17: Electrical installations inspection and maintenance |
| EN 1127-1:2011 | Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology |
| DIN EN 13952:2017-09 | LPG EQUIPMENT AND ACCESSORIES - FILLING OPERATIONS FOR LPG CYLINDERS |
| EN 50628:2016 | Erection of electrical installations in underground mines |
| DIN EN 16299:2013-06 | CATHODIC PROTECTION OF EXTERNAL SURFACES OF ABOVE GROUND STORAGE TANK BASES IN CONTACT WITH SOIL OR FOUNDATIONS |
| EN 60079-29-2:2015 | Explosive atmospheres - Part 29-2: Gas detectors - Selection, installation, use and maintenance of detectors for flammable gases and oxygen |
| DIN EN 15001-2:2010-04 | Gas infrastructure - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 2: Detailed functional requirements for commissioning, operation and maintenance |
| EN 50050-2 : 2013 | ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 2: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE COATING POWDER |
| EN 62305-3:2011 | Protection against lightning - Part 3: Physical damage to structures and life hazard |
| EN 60079-10-2:2015 | Explosive atmospheres - Part 10-2: Classification of areas - Explosive dust atmospheres |
| EN 50050-1:2013 | Electrostatic hand-held spraying equipment - Safety requirements - Part 1: Hand-held spraying equipment for ignitable liquid coating materials |
| EN 60079-20-1:2010 | Explosive atmospheres - Part 20-1: Material characteristics for gas and vapour classification - Test methods and data |
| EN 50223:2015 | Stationary electrostatic application equipment for ignitable flock material - Safety requirements |
| IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| IEC 60079-1:2014 RLV | Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d" |
| EN 60079-26:2015 | Explosive atmospheres - Part 26: Equipment with Equipment Protection Level (EPL) Ga |
| IEC 61024-1:1990 | Protection of structures against lightning - Part 1: General principles |
| EN 60079-29-4:2010 | Explosive atmospheres - Part 29-4: Gas detectors - Performance requirements of open path detectors for flammable gases |
| EN 60079-1:2014 | Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d" |
| EN 60079-10-1:2015 | Explosive atmospheres - Part 10-1: Classification of areas - Explosive gas atmospheres |
| IEC 60079-30-2:2007 | Explosive atmospheres - Part 30-2: Electrical resistance trace heating - Application guide for design, installation and maintenance |
| EN 60079-29-1:2016 | Explosive atmospheres - Part 29-1: Gas detectors - Performance requirements of detectors for flammable gases |
| EN 60034-1:2010/corrigendum Oct. 2010 | ROTATING ELECTRICAL MACHINES - PART 1: RATING AND PERFORMANCE |
| IEC 60079-19:2010+AMD1:2015 CSV | Explosive atmospheres - Part 19: Equipment repair, overhaul and reclamation |
| IEC 60364-4-41:2005+AMD1:2017 CSV | Low voltage electrical installations - Part 4-41: Protection for safety - Protection against electric shock |
| EN 60079-0:2012/A11:2013 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED) |
| ISO 10807:1994 | Pipework — Corrugated flexible metallic hose assemblies for the protection of electrical cables in explosive atmospheres |
| IEC 60079-17:2013 | Explosive atmospheres - Part 17: Electrical installations inspection and maintenance |
| EN 60079-15:2010 | Explosive atmospheres - Part 15: Equipment protection by type of protection "n" |
| EN 60079-19:2011/A1:2015 | EXPLOSIVE ATMOSPHERES - PART 19: EQUIPMENT REPAIR, OVERHAUL AND RECLAMATION (IEC 60079-19:2010) |
| EN 60060-1:2010 | High-voltage test techniques - Part 1: General definitions and test requirements |
| IEC 61008-1:2010+AMD1:2012+AMD2:2013 CSV | Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs) - Part1: General rules |
| HD 60364-4-41:2017/A11:2017 | LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 4-41: PROTECTION FOR SAFETY - PROTECTION AGAINST ELECTRIC SHOCK |
| IEC 60079-18:2014 RLV | Explosive atmospheres - Part 18: Equipment protection by encapsulation “m” |
| IEC 60332-2-2:2004 | Tests on electric and optical fibre cables under fire conditions - Part 2-2: Test for vertical flame propagation for a single small insulated wire or cable - Procedure for diffusion flame |
| EN 60079-10-2:2015 | Explosive atmospheres - Part 10-2: Classification of areas - Explosive dust atmospheres |
| IEC 60079-10-1:2015 | Explosive atmospheres - Part 10-1: Classification of areas - Explosive gas atmospheres |
| IEC 60079-29-4:2009 | Explosive atmospheres - Part 29-4: Gas detectors - Performance requirements of open path detectors for flammable gases |
| IEC 61241-11:2005 | Electrical apparatus for use in the presence of combustible dust - Part 11: Protection by intrinsic safety 'iD' |
| EN 60079-6:2015 | Explosive atmospheres - Part 6: Equipment protection by liquid immersion "o" |
| IEC 61558-2-6:2009 | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers |
| EN 60332-1-2:2004/A11:2016 | TESTS ON ELECTRIC AND OPTICAL FIBRE CABLES UNDER FIRE CONDITIONS - PART 1-2: TEST FOR VERTICAL FLAME PROPAGATION FOR A SINGLE INSULATED WIRE OR CABLE - PROCEDURE FOR 1 KW PRE-MIXED FLAME (IEC 60332-1-2:2004/A1:2015) |
| EN 60079-28:2015 | Explosive atmospheres - Part 28: Protection of equipment and transmission systems using optical radiation |
| IEC TR 60079-16:1990 | Electrical apparatus for explosive gas atmospheres. Part 16: Artificial ventilation for the protection of analyser(s) houses |
| IEC 60614-2-5:1992 | Specifications for conduits for electrical installations - Part 2: Particular specifications for conduits - Section 5: Flexible conduits |
| IEC 60079-5:2015 RLV | Explosive atmospheres - Part 5: Equipment protection by powder filling "q" |
| IEC 60332-1-2:2004+AMD1:2015 CSV | Tests on electric and optical fibre cables under fire conditions - Part 1-2: Test for vertical flame propagation for a single insulatedwire or cable - Procedure for 1 kW pre-mixed flame |
| EN 60079-30-1:2017 | Explosive atmospheres - Part 30-1: Electrical resistance trace heating - General and testing requirements |
| EN 60079-11:2012 | Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i" |
| IEC 60079-11:2011 | Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i" |
| EN 62305-3:2011 | Protection against lightning - Part 3: Physical damage to structures and life hazard |
| IEC TS 60034-25:2014 | Rotating electrical machines - Part 25: AC electrical machines used in power drive systems - Application guide |
| IEC 61241-1:2004 | Electrical apparatus for use in the presence of combustible dust - Part 1: Protection by enclosures "tD" |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC TS 60034-17:2006 | Rotating electrical machines - Part 17: Cage induction motors when fed from converters - Application guide |
| IEC 60755:2017 | General safety requirements for residual current operated protective devices |
| IEC 60079-29-2:2015 RLV | Explosive atmospheres - Part 29-2: Gas detectors - Selection, installation, use and maintenance of detectors for flammable gases and oxygen |
| EN 50272-2:2001 | Safety requirements for secondary batteries and battery installations - Part 2: Stationary batteries |
| IEC 60079-6:2015 | Explosive atmospheres - Part 6: Equipment protection by liquid immersion "o" |
| IEC 60079-0:2011 | Explosive atmospheres - Part 0: Equipment - General requirements |
| IEC 60034-1:2017 | Rotating electrical machines - Part 1: Rating and performance |
| EN 60243-1:2013 | ELECTRIC STRENGTH OF INSULATING MATERIALS - TEST METHODS - PART 1: TESTS AT POWER FREQUENCIES (IEC 60243-1:2013) |
| IEC 61241-4:2001 | Electrical apparatus for use in the presence of combustible dust - Part 4: Type of protection "pD" |
| IEC 60079-31:2013 | Explosive atmospheres - Part 31: Equipment dust ignition protection by enclosure "t" |
| IEC 60079-30-1:2007 | Explosive atmospheres - Part 30-1: Electrical resistance trace heating - General and testing requirements |
| EN 61558-2-6:2009 | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers |
| IEC 61285:2015 | Industrial-process control - Safety of analyser houses |
| IEC 61439-1:2011 | Low-voltage switchgear and controlgear assemblies - Part 1: General rules |
| EN 60079-17:2014 | Explosive atmospheres - Part 17: Electrical installations inspection and maintenance |
| IEC 61241-2-1:1994 | Electrical apparatus for use in the presence of combustible dust - Part 2: Test methods - Section 1: Methods for determining the minimum ignition temperatures of dust |
| CLC/TR 50427:2004 | Assessment of inadvertent ignition of flammable atmospheres by radio-frequency radiation - Guide |
| EN 61010-1:2010 | Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements |
| IEC 60060-1:2010 | High-voltage test techniques - Part 1: General definitions and test requirements |
| IEC 61010-1:2010+AMD1:2016 CSV | Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements |
| IEC 62305-3:2010 | Protection against lightning - Part 3: Physical damage to structures and life hazard |
| EN 60079-13:2017 | Explosive atmospheres - Part 13: Equipment protection by pressurized room "p" and artificially ventilated room "v" |
| IEC 60079-15:2010 | Explosive atmospheres - Part 15: Equipment protection by type of protection "n" |
| IEC 60079-13:2017 | Explosive atmospheres - Part 13: Equipment protection by pressurized room "p" and artificially ventilated room "v" |
| EN 61285:2015 | Industrial-process control - Safety of analyzer houses |
| IEC 60079-26:2014 RLV | Explosive atmospheres - Part 26: Equipment with Equipment Protection Level (EPL) Ga |
| CLC/TR 50404:2003 | Electrostatics - Code of practice for the avoidance of hazards due to static electricity |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.