EN 60317-0-2:2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Specifications for particular types of winding wires - Part 0-2: General requirements - Enamelled rectangular copper wire
08-27-2020
01-17-2014
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms, definitions, general notes and appearance
4 Dimensions
5 Electrical resistance
6 Elongation
7 Springiness
8 Flexibility and adherence
9 Heat shock
10 Cut-through
11 Resistance to abrasion
12 Resistance to solvents
13 Breakdown voltage
14 Continuity of insulation
15 Temperature index
16 Resistance to refrigerants
17 Solderability
18 Heat or solvent bonding
19 Dielectric dissipation factor
20 Resistance to transformer oil
21 Loss of mass
23 Pin hole test
30 Packaging
Annex A (informative) - Nominal cross-sectional areas
for preferred and intermediate sizes
Annex B (informative) - Special tolerances
Bibliography
Annex ZA (normative) - Normative references to
international publications with their
corresponding European publications
IEC 60317-0-2:2013 specifies the general requirements of enamelled rectangular copper winding wires. The range of nominal conductor dimensions is given in the relevant specification sheet. This third edition cancels and replaces the second edition published in 1997, Amendment 1:1999 and Amendment 2:2005. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - addition of 3.2.2, transferring general winding wire requirements from the scope; - correction to Table 7 units; - change to Clause 15 requirements with a simple reference to IEC 60172; - deletion of Annex E. Key words: requirements of enamelled rectangular copper winding wires
| DocumentType |
Standard
|
| PublisherName |
European Committee for Standards - Electrical
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| SN EN 60317-0-2:2014 | Identical |
| UNE-EN 60317-0-2:1998 | Identical |
| IEC 60317-0-2:2013 | Identical |
| NF EN 60317 0-2 : 2014 | Identical |
| NBN EN 60317 0-2 : 2014 | Identical |
| NEN EN IEC 60317-0-2 : 2014 | Identical |
| I.S. EN 60317-0-2:2014 | Identical |
| PN EN 60317-0-2 : 2014 | Identical |
| SN EN 60317-0-2 : 1998 AMD 1 2000 | Identical |
| BS EN 60317-0-2:2014 | Identical |
| CEI EN 60317-0-2 : 2014 | Identical |
| DIN EN 60317-0-2:2014-10 | Identical |
| OVE/ONORM EN 60317-0-2 : 2014 | Identical |
| UNE-EN 60317-0-2:2014 | Identical |
| NEN 10317-0-2 : 95 AMD 2 95 | Similar to |
| CEI EN 60317-58 : 2011 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 58: POLYAMIDE-IMIDE ENAMELLED RECTANGULAR COPPER WIRE, CLASS 220 |
| BS EN 60317-17:2010 | Specifications for particular types of winding wires Polyvinyl acetal enamelled rectangular copper wire, class 105 |
| BS EN 60317-44 : 1997 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 44: AROMATIC POLYIMIDE TAPE WRAPPED RECTANGULAR COPPER WIRE, CLASS 240 |
| I.S. EN 60317-28:2014 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 28: POLYESTERIMIDE ENAMELLED RECTANGULAR COPPER WIRE, CLASS 180 |
| BS EN 60317-18 : 2004 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 18: POLYVINYL ACETAL ENAMELLED RECTANGULAR COPPER WIRE, CLASS 120 |
| BS EN 60317-29 : 1997 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 29: POLYESTER OR POLYESTERIMIDE OVERCOATED WITH POLYAMIDE-IMIDE ENAMELLED RECTANGULAR COPPER WIRE, CLASS 200 |
| CEI EN 60317-47 : 2014 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 47: AROMATIC POLYIMIDE ENAMELLED RECTANGULAR COPPER WIRE, CLASS 240 |
| I.S. EN 60317-47:2014 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 47: AROMATIC POLYIMIDE ENAMELLED RECTANGULAR COPPER WIRE, CLASS 240 |
| BS EN 60317-27:2014 | Specifications for particular types of winding wires Paper tape covered rectangular copper wire |
| I.S. EN 60317-17:2010 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 17: POLYVINYL ACETAL ENAMELLED RECTANGULAR COPPER WIRE, CLASS 105 |
| I.S. EN 60317-44:1998 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - AROMATIC POLYIMIDE TAPE WRAPPED RECTANGULAR COPPER WIRE, CLASS 240 |
| EN 60317-27:2014 | Specifications for particular types of winding wires - Part 27: Paper tape covered rectangular copper wire |
| EN 60317-18:2004/A1:2010 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 18: POLYVINYL ACETAL ENAMELLED RECTANGULAR COPPER WIRE, CLASS 120 |
| EN 60317-17:2010 | Specifications for particular types of winding wires - Part 17: Polyvinyl acetal enamelled rectangular copper wire, class 105 |
| I.S. EN 60317-18:2004 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 18: POLYVINYL ACETAL ENAMELLED RECTANGULAR COPPER WIRE, CLASS 120 |
| UNE-EN 60317-17:2010 | Specifications for particular types of winding wires - Part 17: Polyvinyl acetal enamelled rectangular copper wire, class 105 |
| UNE-EN 60317-29:1996 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES. PART 29: POLYESTERIMIDE OVERCOATED WITH POLYAMIDE-IMIDE ENAMELLED RECTANGULAR COPPER WIRE, CLASS 200. |
| CEI EN 60317-17 : 2011 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 17: POLYVINYL ACETAL ENAMELLED RECTANGULAR COPPER WIRE, CLASS 105 |
| BS EN 60317-58:2010 | Specifications for particular types of winding wires Polyamide-imide enamelled rectangular copper wire, class 220 |
| BS EN 60317-47:2014 | Specifications for particular types of winding wires Aromatic polyimide enamelled rectangular copper wire, class 240 |
| I.S. EN 60317-30:1998 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 30: POLYIMIDE ENAMELLED RECTANGULAR COPPER WIRE, CLASS 220 |
| I.S. EN 60317-58:2010 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 58: POLYAMIDE-IMIDE ENAMELLED RECTANGULAR COPPER WIRE, CLASS 220 |
| I.S. EN 60317-16:1996 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 16: POLYESTER ENAMELLED RECTANGULAR COPPER WIRE, CLASS 155 |
| UNE-EN 60317-44:1997 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES. PART 44: AROMATIC POLYIMIDE TAPE WRAPPED RECTANGULAR COPPER WIRE, CLASS 240. |
| BS EN 60317-28:2014 | Specifications for particular types of winding wires Polyesterimide enamelled rectangular copper wire, class 180 |
| UNE-EN 60317-58:2011 | Specifications for particular types of winding wires -- Part 58: Polyamide-imide enamelled rectangular copper wire, class 220 |
| BS EN 60317-30:1997 | Specifications for particular types of winding wires Polyimide enamelled rectangular copper wire, class 220 |
| I.S. EN 60317-27:2014 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 27: PAPER TAPE COVERED RECTANGULAR COPPER WIRE |
| I.S. EN 60317-29:1998 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 29: POLYESTER OR POLYESTERIMIDE OVERCOATED WITH POLYAMIDE-IMIDE ENAMELLED RECTANGULAR COPPER WIRE, CLASS 200 |
| UNE-EN 60317-47:2014 | Specifications for particular types of winding wires - Part 47: Aromatic polyimide enamelled rectangular copper wire, class 240 |
| EN 60317-28:2014 | Specifications for particular types of winding wires - Part 28: Polyesterimide enamelled rectangular copper wire, class 180 |
| EN 60317-47:2014 | Specifications for particular types of winding wires - Part 47: Aromatic polyimide enamelled rectangular copper wire, class 240 |
| EN 60317-44:1997/A1:2010 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 44: AROMATIC POLYIMIDE TAPE WRAPPED RECTANGULAR COPPER WIRE, CLASS 240 |
| EN 60317-58 : 2010 | Specifications for particular types of winding wires - Part 58: Polyamide-imide enamelled rectangular copper wire, class 220 |
| EN 60317-29:1996/A2:2010 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 29: POLYESTER OR POLYESTERIMIDE OVERCOATED WITH POLYAMIDE-IMIDE ENAMELLED RECTANGULAR COPPER WIRE, CLASS 200 |
| EN 60317-30:1996/A2:2005 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 30: POLYIMIDE ENAMELLED RECTANGULAR COPPER WIRE, CLASS 220 |
| ISO 3:1973 | Preferred numbers Series of preferred numbers |
| IEC 60172:2015 | Test procedure for the determination of the temperature index of enamelled and tape wrapped winding wires |
| EN 60172:2015 | Test procedure for the determination of the temperature index of enamelled and tape wrapped winding wires |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.