• There are no items in your cart

EN 60851-5:2008/A1:2011

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

WINDING WIRES - TEST METHODS - PART 5: ELECTRICAL PROPERTIES (IEC 60851-5:2008)
Amendment of

EN 60851-5:2008

Superseded date

02-07-2022

Published date

01-12-2013

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Test 5: Electrical resistance
4 Test 13: Breakdown voltage
5 Test 14: Continuity of insulation (applicable to
  enamelled round and tape wrapped round wire)
6 Test 19: Dielectric dissipation factor (applicable to
  enamelled wire and bunched wire)
7 Test 23: Pin hole test
Annex A (informative) - Dissipation factor methods
Annex ZA (normative) - Normative references to international
         publications with their corresponding European
         publications

Describes the following tests: - Test 5: Electrical resistance; - Test 13: Breakdown voltage; - Test 14: Continuity of insulation; - Test 19: Dielectric dissipation factor; - Test 23: Pin hole.

Committee
TC 55
DevelopmentNote
Supersedes HD 490.5 (06/2004)
DocumentType
Standard
PublisherName
European Committee for Standards - Electrical
Status
Superseded
SupersededBy

I.S. EN 60851-2:2009 WINDING WIRES - TEST METHODS - PART 2: DETERMINATION OF DIMENSIONS
BS EN 60851-1 : 1998 WINDING WIRES - TEST METHODS - PART 1: GENERAL
CEI EN 60317-25 : 2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 25: POLYESTER OR POLYESTERIMIDE OVERCOATED WITH POLYAMIDE-IMIDE ENAMELLED ROUND ALUMINIUM WIRE, CLASS 200
CEI EN 60317-0-7 : 2012 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-7: GENERAL REQUIREMENTS - FULLY INSULATED (FIW) ZERODEFECT ENAMELLED ROUND COPPER WIRE
UNE-EN 60851-2:2010 Winding wires - Test methods -- Part 2: Determination of dimensions
UNE-EN 60851-6:2012 Winding wires - Test methods - Part 6: Thermal properties
BS EN 61558-1 : 2005 SAFETY OF POWER TRANSFORMERS, POWER SUPPLIES, REACTORS AND SIMILAR PRODUCTS - PART 1: GENERAL REQUIREMENTS AND TESTS
BS EN 60950:2000 Safety of information technology equipment
EN 60851-4:2016 Winding wires - Test methods - Part 4: Chemical properties
EN 61558-1:2005/A1:2009 SAFETY OF POWER TRANSFORMERS, POWER SUPPLIES, REACTORS AND SIMILAR PRODUCTS - PART 1: GENERAL REQUIREMENTS AND TESTS
EN 61558-2-16:2009/A1:2013 SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND SIMILAR PRODUCTS FOR SUPPLY VOLTAGES UP TO 1 100 V - PART 2-16: PARTICULAR REQUIREMENTS AND TESTS FOR SWITCH MODE POWER SUPPLY UNITS AND TRANSFORMERS FOR SWITCH MODE POWER SUPPLY UNITS (IEC 61558-2-16:2009/A1:2013)
EN 60317-25:2010 Specifications for particular types of winding wires - Part 25: Polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire, class 200
EN 60950-1:2006/A2:2013 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60950-1:2005/A2:2013, MODIFIED)
EN 60851-2:2009/A1:2015 WINDING WIRES - TEST METHODS - PART 2: DETERMINATION OF DIMENSIONS
12/30258456 DC : 0 BS EN 60950-1:2006/FPRAE:2011 - INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS
BS EN 60851-6:1998 Methods of test for winding wires Thermal properties
I.S. EN 60851-1:1998 WINDING WIRES - TEST METHODS - PART 1: GENERAL
EN 60065:2014/AC:2017-01 AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS (IEC 60065:2014/COR2:2016)
EN IEC 61204-7:2018 Low-voltage switch mode power supplies - Part 7: Safety requirements
I.S. EN 60601- 1:2006&A1:2013&AC:2014&A12:2014 MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE
I.S. EN 60317-0-6:2001 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-6: GENERAL REQUIREMENTS - GLASS-FIBRE WOUND RESIN OR VARNISH IMPREGNATED, BARE OR ENAMELLED ROUND COPPER WIRE
CEI EN 60317-0-10 : 1ED 2017 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-10: GENERAL REQUIREMENTS - POLYESTER GLASS-FIBRE WOUND FUSED, UNVARNISHED, OR RESIN OR VARNISH IMPREGNATED, BARE OR ENAMELLED ROUND COPPER WIRE
BS EN 60065 : 2014 AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS (IEC 60065:2014, MODIFIED)
I.S. EN IEC 61204-7:2018 LOW-VOLTAGE SWITCH MODE POWER SUPPLIES - PART 7: SAFETY REQUIREMENTS
I.S. EN 60950-1:2006 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60950-1:2005 (MOD))
UNE-EN 60317-25:2010 Specifications for particular types of winding wires - Part 25: Polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire, class 200
UNE-EN 60950-1:2007 Information technology equipment - Safety - Part 1: General requirements
BS EN 60851-4:1998 Winding Wires. Test methods Chemical properties
UNE-EN 60065:2015 Audio, video and similar electronic apparatus - Safety requirements
12/30258453 DC : 0 BS EN 62368-1 AMD - AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS
I.S. EN 60851-4:2016 WINDING WIRES - TEST METHODS - PART 4: CHEMICAL PROPERTIES
I.S. EN 60851-6:2012 WINDING WIRES - TEST METHODS - PART 6: THERMAL PROPERTIES (IEC 60851-6:2012 (EQV))
CEI EN 62368-1 : 2016 AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS
I.S. EN 60065:2014 AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS
I.S. EN 62368-1:2014 AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS (IEC 62368-1:2014, MODIFIED)
I.S. EN 60317-0-10:2017 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-10: GENERAL REQUIREMENTS - POLYESTER GLASS-FIBRE WOUND FUSED, UNVARNISHED, OR RESIN OR VARNISH IMPREGNATED, BARE OR ENAMELLED ROUND COPPER WIRE
EN 60851-1:1996/A2:2009 WINDING WIRES - TEST METHODS - PART 1: GENERAL
EN 62368-1:2014/AC:2017-03 AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS (IEC 62368-1:2014, MODIFIED)
I.S. EN 60317-0-7:2017 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-7: GENERAL REQUIREMENTS - FULLY INSULATED (FIW) ZERO-DEFECT ENAMELLED ROUND COPPER WIRE
I.S. EN 61558-1:2006 SAFETY OF POWER TRANSFORMERS, POWER SUPPLIES, REACTORS AND SIMILAR PRODUCTS - PART 1: GENERAL REQUIREMENTS AND TESTS
BS EN 60601-1 : 2006 MEDICAL ELECTRICAL EQUIPMENT PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE
BS EN 61558-2-16 : 2009 SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND SIMILAR PRODUCTS FOR SUPPLY VOLTAGES UP TO 1100 V - PART 2-16: PARTICULAR REQUIREMENTS AND TESTS FOR SWITCH MODE POWER SUPPLY UNITS AND TRANSFORMERS FOR SWITCH MODE POWER SUPPLY UNITS
BS EN 60950-1 : 2006 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS
BS EN 60317-0-7:2017 Specifications for particular types of winding wires General requirements. Fully insulated (FIW) zero-defect enamelled round copper wire
BS EN 60317-0-10:2017 Specifications for particular types of winding wires General requirements. Polyester glass-fibre wound fused, unvarnished, or resin or varnish impregnated, bare or enamelled round copper wire
UNE-EN 60317-0-10:2017 Specifications for particular types of winding wires - Part 0-10: General requirements - Polyester glass-fibre wound fused, unvarnished, or resin or varnish impregnated, bare or enamelled round copper wire
EN 60317-0-7:2017 Specifications for particular types of winding wires - Part 0-7: General requirements - Fully insulated (FIW) zero-defect enamelled round copper wire
I.S. EN 60317-25:2010 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 25: POLYESTER OR POLYESTERIMIDE OVERCOATED WITH POLYAMIDE-IMIDE ENAMELLED ROUND ALUMINIUM WIRE, CLASS 200
BS EN 60317-25:2010 Specifications for particular types of winding wires Polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire, class 200
UNE-EN 60317-0-7:2012 Specifications for particular types of winding wires - Part 0-7: General requirements - Fully insulated (FIW) zero-defect enamelled round copper wire with nominal conductor diameter of 0,040 mm to 1,600 mm
BS EN 60851-2 : 2009 WINDING WIRES - TEST METHODS - PART 2: DETERMINATION OF DIMENSIONS
IEC 60950:1999 Safety of information technology equipment
EN 60317-0-10:2017 Specifications for particular types of winding wires - Part 0-10: General requirements - Polyester glass-fibre wound fused, unvarnished, or resin or varnish impregnated, bare or enamelled round copper wire
EN 60950:2000/corrigendum:2002 SAFETY OF INFORMATION TECHNOLOGY EQUIPMENT
EN 60851-6:2012 Winding wires - Test methods - Part 6: Thermal properties
OVE/ONORM EN 60317-0-6 : 2007 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-6: GENERAL REQUIREMENTS - GLASS-FIBRE WOUND RESIN OR VARNISH IMPREGNATED, BARE OR ENAMELLED ROUND COPPER WIRE
UNE-EN 60851-1:1997 WINDING WIRES. TEST METHODS. PART 1: GENERAL.

IEC 60851-1:1996 Methods of test for winding wires - Part 1: General
EN 60851-1:1996/A2:2009 WINDING WIRES - TEST METHODS - PART 1: GENERAL

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.