EN 61400-1:2005/A1:2010
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
WIND TURBINES - PART 1: DESIGN REQUIREMENTS
Amendment of
Superseded date
02-05-2022
Published date
01-12-2013
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Principal elements
6 External conditions
7 Structural design
8 Control and protection system
9 Mechanical systems
10 Electrical system
11 Assessment of a wind turbine for site-specific conditions
12 Assembly, installation and erection
13 Commissioning, operation and maintenance
Annex A (normative) - Design parameters for describing wind
turbine class S
Annex B (informative) - Turbulence models
Annex C (informative) - Assessment of earthquake loading
Annex D (informative) - Wake and wind farm turbulence
Annex E (informative) - Prediction of wind distribution for
wind turbine sites by measure-correlate-predict (MCP)
methods
Annex F (informative) - Statistical extrapolation of loads for
ultimate strength analysis
Annex G (informative) - Fatigue analysis using Miner's rule
with load extrapolation
Annex H (informative) - Contemporaneous loads
Annex ZA (normative) - Normative references to international
publications with their corresponding European
publications
Bibliography
Defines essential design requirements to ensure the engineering integrity of wind turbines. Provides an appropriate level of protection against damage from all hazards during the planned lifetime.
| Committee |
TC 88
|
| DevelopmentNote |
Supersedes ENV 61400-1 (03/2004)
|
| DocumentType |
Standard
|
| PublisherName |
European Committee for Standards - Electrical
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| OVE/ONORM EN 61400-1 : 2011 | Identical |
| UNE-EN 61400-1:2006 | Identical |
| NBN EN 61400-1 : 2006 AMD 1 2011 | Identical |
| DIN EN 61400-1 : 2011 | Identical |
| NF EN 61400-1 : 2006 AMD 1 2015 | Identical |
| CEI EN 61400-1/A1:2011 | Identical |
| BS EN 61400-1 : 2005 | Identical |
| SN EN 61400-1 : 2005 | Identical |
| VDE 0127-1 : 2011 | Identical |
| PN EN 61400-1:2006 | Identical |
| IEC 61400-1:2005+AMD1:2010 CSV | Identical |
| PN EN 61400-1 : 2006 AMD 1 2010 | Identical |
| NEN EN IEC 61400-1 : 2005 AMD 1 2010 | Identical |
| I.S. EN 61400-1:2005 | Identical |
| BS EN 61400-3:2009 | Wind turbines Design requirements for offshore wind turbines |
| BS EN 61400-4:2013 | Wind turbines Design requirements for wind turbine gea |
| CEI EN 61400-22 : 2011 | WIND TURBINES - PART 22: CONFORMITY TESTING AND CERTIFICATION |
| UNE-EN 61400-23:2014 | Wind turbines - Part 23: Full-scale structural testing of rotor blades |
| I.S. EN 60076-16:2011 | POWER TRANSFORMERS - PART 16: TRANSFORMERS FOR WIND TURBINES APPLICATIONS (IEC 60076-16:2011) |
| EN 61400-23:2014 | Wind turbines - Part 23: Full-scale structural testing of rotor blades |
| EN 61400-2:2014 | Wind turbines - Part 2: Small wind turbines |
| EN 61400-3:2009 | Wind turbines - Part 3: Design requirements for offshore wind turbines |
| 14/30304623 DC : 0 | BS ISO 29404 - SHIPS AND MARINE TECHNOLOGY - SPECIFIC REQUIREMENTS FOR OFFSHORE WIND FARM COMPONENTS - SUPPLY CHAIN INFORMATION FLOW |
| CLC/TS 61400-26-1:2017 | Wind turbines - Part 26-1: Time-based availability for wind turbine generating systems |
| CEI EN 60076-16 : 2012 | POWER TRANSFORMERS - PART 16: TRANSFORMERS FOR WIND TURBINES APPLICATIONS |
| I.S. EN 61400-2:2014 | WIND TURBINES - PART 2: SMALL WIND TURBINES |
| I.S. EN 61400-4:2013 | WIND TURBINES - PART 4: DESIGN REQUIREMENTS FOR WIND TURBINE GEARBOXES (IEC 61400-4:2012 (EQV)) |
| CEI EN 61400-3 : 2009 | WIND TURBINES - PART 3: DESIGN REQUIREMENTS FOR OFFSHORE WIND TURBINES |
| BS EN 60076-16:2011 | Power transformers Transformers for wind turbines applications |
| I.S. EN 61400-13:2016 | WIND TURBINES - PART 13: MEASUREMENT OF MECHANICAL LOADS |
| TR 102 532 : 1.2.1 | ENVIRONMENTAL ENGINEERING (EE); THE USE OF ALTERNATIVE ENERGY SOLUTIONS IN TELECOMMUNICATION INSTALLATIONS |
| UNE-EN 61400-22:2011 | Wind turbines - Part 22: Conformity testing and certification |
| CEI EN 61400-23 : 2014 | WIND TURBINES - PART 23: FULL-SCALE STRUCTURAL TESTING OF ROTOR BLADES |
| BS EN 61400-13:2016 | Wind turbines Measurement of mechanical loads |
| BS EN 62310-3:2008 | Static transfer systems (STS) Method for specifying performance and test requirements |
| UNE-EN 60076-16:2012 | Power transformers - Part 16: Transformers for wind turbines applications |
| PD CLC/TS 61400-26-1:2017 | Wind turbines Time-based availability for wind turbine generating systems |
| S.R. CLC/TS 61400-26-1:2017 | WIND TURBINES - PART 26-1: TIME-BASED AVAILABILITY FOR WIND TURBINE GENERATING SYSTEMS |
| EN 61400-22:2011 | Wind turbines - Part 22: Conformity testing and certification |
| UNE-EN 61400-4:2013 | Wind turbines - Part 4: Design requirements for wind turbine gearboxes |
| EN 60076-16:2011 | Power transformers - Part 16: Transformers for wind turbines applications |
| EN 62310-3:2008 | Static transfer systems (STS) - Part 3: Method for specifying performance and test requirements |
| BS EN 61400-21:2008 | Wind turbines Measurement and assessment of power quality characteristics of grid connected wind turbines |
| BS EN 61400-23:2014 | Wind turbines Full-scale structural testing of rotor blades |
| I.S. EN 61400-23:2014 | WIND TURBINES - PART 23: FULL-SCALE STRUCTURAL TESTING OF ROTOR BLADES |
| I.S. EN 61400-3:2009 | WIND TURBINES - PART 3: DESIGN REQUIREMENTS FOR OFFSHORE WIND TURBINES |
| I.S. EN 61400-22:2011 | WIND TURBINES - PART 22: CONFORMITY TESTING AND CERTIFICATION |
| EN 61400-13:2016 | Wind turbines - Part 13: Measurement of mechanical loads |
| EN 61400-21:2008 | WIND TURBINES - PART 21: MEASUREMENT AND ASSESSMENT OF POWER QUALITY CHARACTERISTICS OF GRID CONNECTED WIND TURBINES |
| EN 61400-4:2013 | Wind turbines - Part 4: Design requirements for wind turbine gearboxes |
| IEC 60364-5-54:2011 | Low-voltage electrical installations - Part 5-54: Selection and erection of electrical equipment - Earthing arrangements and protective conductors |
| IEC 60038:2009 | IEC standard voltages |
| IEC 61000-6-4:2006+AMD1:2010 CSV | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-4: GENERIC STANDARDS - EMISSION STANDARD FOR INDUSTRIAL ENVIRONMENTS |
| EN 61000-6-1:2007 | Electromagnetic compatibility (EMC) - Part 6-1: Generic standards - Immunity for residential, commercial and light-industrial environments |
| EN 61400-2:2014 | Wind turbines - Part 2: Small wind turbines |
| IEC 60898:1995 | Electrical accessories - Circuit-breakers for overcurrent protection for household and similar installations |
| ISO 3010:2017 | Bases for design of structures — Seismic actions on structures |
| IEC 61310-2:2007 | Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking |
| EN 62305-4:2011/AC:2016 | PROTECTION AGAINST LIGHTNING - PART 4: ELECTRICAL AND ELECTRONIC SYSTEMS WITHIN STRUCTURES (IEC 62305-4:2010) |
| ISO 6336-2:2006 | Calculation of load capacity of spur and helical gears Part 2: Calculation of surface durability (pitting) |
| IEC 61000-6-2:2016 | Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity standard for industrial environments |
| IEC 61400-24:2010 | Wind turbines - Part 24: Lightning protection |
| ISO 4354:2009 | Wind actions on structures |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| HD 60364-5-54:2011/A11:2017 | LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-54: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - EARTHING ARRANGEMENTS AND PROTECTIVE CONDUCTORS |
| ISO 2394:2015 | General principles on reliability for structures |
| IEC 61000-6-1 : 3.0 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-1: GENERIC STANDARDS - IMMUNITY STANDARD FOR RESIDENTIAL, COMMERCIAL AND LIGHT-INDUSTRIAL ENVIRONMENTS |
| IEC 60204-11:2000 | Safety of machinery - Electrical equipment of machines - Part 11: Requirements for HV equipment for voltages above 1 000 V a.c. or 1 500 V d.c. and not exceeding 36 kV |
| ISO 6336-3:2006 | Calculation of load capacity of spur and helical gears Part 3: Calculation of tooth bending strength |
| ISO 2533:1975 | Standard Atmosphere |
| HD 478.2.1 : 200S1 | CLASSIFICATION OF ENVIRONMENTAL CONDITIONS - ENVIRONMENTAL CONDITIONS APPEARING IN NATURE - TEMPERATURE AND HUMIDITY |
| ISO 281:2007 | Rolling bearings Dynamic load ratings and rating life |
| IEC 60721-2-1:2013 | Classification of environmental conditions - Part 2-1: Environmental conditions appearing in nature - Temperature and humidity |
| EN 62305-3:2011 | Protection against lightning - Part 3: Physical damage to structures and life hazard |
| EN 61400-21:2008 | WIND TURBINES - PART 21: MEASUREMENT AND ASSESSMENT OF POWER QUALITY CHARACTERISTICS OF GRID CONNECTED WIND TURBINES |
| IEC TR 60755:2008 | General requirements for residual current operated protective devices |
| EN 61000-6-2:2005/corrigendum:2005 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY FOR INDUSTRIAL ENVIRONMENTS (IEC 61000-6-2:2005) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN 61400-24:2010 | Wind turbines - Part 24: Lightning protection |
| ISO 81400-4:2005 | Wind turbines Part 4: Design and specification of gearboxes |
| EN 61000-6-4:2007/A1:2011 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-4: GENERIC STANDARDS - EMISSION STANDARD FOR INDUSTRIAL ENVIRONMENTS |
| IEC 61400-2:2013 | Wind turbines - Part 2: Small wind turbines |
| IEC 61000-6-1:2016 | Electromagnetic compatibility (EMC) - Part 6-1: Generic standards - Immunity standard for residential, commercial and light-industrial environments |
| ISO 9001:2015 | Quality management systems — Requirements |
| IEC 61000-6-4:2006+AMD1:2010 CSV | Electromagnetic compatibility (EMC) - Part 6-4: Generic standards - Emission standard for industrial environments |
| ISO 8930:1987 | General principles on reliability for structures List of equivalent terms |
| EN 60204-11:2000/corrigendum:2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 11: REQUIREMENTS FOR HV EQUIPMENT FOR VOLTAGES ABOVE 1000 V A.C. OR 1500 V D.C. AND NOT EXCEEDING 36 KV |
| IEC 62305-4:2010 | Protection against lightning - Part 4: Electrical and electronic systems within structures |
| IEC 61310-1:2007 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| IEC 60173:1964 | Colours of the cores of flexible cables and cords |
| IEC 61000-6-2 : 3.0:2016 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY STANDARD FOR INDUSTRIAL ENVIRONMENTS |
| IEC 62305-3:2010 | Protection against lightning - Part 3: Physical damage to structures and life hazard |
| ISO 76:2006 | Rolling bearings Static load ratings |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
| IEC 61400-21:2008 | Wind turbines - Part 21: Measurement and assessment of power quality characteristics of grid connected wind turbines |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.