EN ISO 10440-2:2001
Current
The latest, up-to-date edition.
12-01-2001
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Basic design
4.1 General
4.2 Pressure casing
4.3 Casing connections
4.4 External forces and moments
4.5 Rotating elements
4.6 Seals
4.7 Dynamics
4.8 Bearings and bearing housings
4.9 Bearing housings
4.10 Lube oil and seal oil systems
4.11 Materials
4.12 Nameplates
5 Accessories
5.1 Drivers
5.2 Couplings and guards
5.3 Mounting plates
5.4 Controls and instrumentation
5.5 Piping and appurtenances
6 Inspection, testing, and preparation for shipment
6.1 General
6.2 Inspection
6.3 Testing
6.4 Preparation for shipment
7 Vendor's data
7.1 Proposals
7.2 Contract information
Annex A (normative) Data sheets
Bibliography
This part of ISO 10440 covers the minimum requirements for helical, spiral and straight-lobe, oil-free rotarycompressors used for applications up to 0,20 MPa in refinery services. It is applicable to air (and other inert gas)compressors that are in continuous duty on process units.This part of ISO 10440 is not applicable to oil injected rotary compressors.NOTE A bullet (?) at the beginning of a clause or sub-clause indicates that either a decision is required or furtherinformation is to be provided by the purchaser. This information should be indicated on the data sheets; otherwise it should bestated in the quotation request or in the order.
| Committee |
CEN/TC 12
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| Standards | Relationship |
| SN EN ISO 10440-2 : 2001 | Identical |
| UNI EN ISO 10440-2 : 2003 | Identical |
| NF EN ISO 10440-2 : 2002 | Identical |
| PN EN ISO 10440-2 : 2005 | Identical |
| I.S. EN ISO 10440-2:2002 | Identical |
| NEN EN ISO 10440-2 : 2002 | Identical |
| NS EN ISO 10440-2 : 1ED 2002 | Identical |
| ISO 10440-2:2001 | Identical |
| DIN EN ISO 10440-2:2003-02 | Identical |
| UNE-EN ISO 10440-2:2001 | Identical |
| BS EN ISO 10440-2:2001 | Identical |
| NBN EN ISO 10440-2 : 2002 | Identical |
| BS EN 62282-3-100:2012 | Fuel cell technologies Stationary fuel cell power systems. Safety |
| BS EN 62282-3-1:2007 | Fuel cell technologies Stationary fuel cell power systems. Safety |
| EN 62282-3-1 : 2007 | FUEL CELL TECHNOLOGIES - PART 3-1: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY |
| I.S. EN 62282-3-1:2007 | FUEL CELL TECHNOLOGIES - PART 3-1: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY |
| EN 62282-3-100:2012 | Fuel cell technologies - Part 3-100: Stationary fuel cell power systems - Safety |
| CEI EN 62282-3-100 : 2012 | FUEL CELL TECHNOLOGIES - PART 3-100: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY |
| UNE-EN 62282-3-1:2011 | Fuel cell technologies - Part 3-1: Stationary fuel cell power systems - Safety |
| I.S. EN 62282-3-100:2012 | FUEL CELL TECHNOLOGIES - PART 3-100: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY (IEC 62282-3-100:2012 (EQV)) |
| IEC 60060-2:2010 | High-voltage test techniques - Part 2: Measuring systems |
| ISO 1328-2:1997 | Cylindrical gears ISO system of accuracy Part 2: Definitions and allowable values of deviations relevant to radial composite deviations and runout information |
| API 661 : 2015 | PETROLEUM, PETROCHEMICAL, AND NATURAL GAS INDUSTRIES - AIR-COOLED HEAT EXCHANGERS |
| ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs |
| ASME B31.1 : 2016 | POWER PIPING |
| IEC 61000-4-4 : 3.0EN+(REDLINE+VERSION) | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-4: TESTING AND MEASUREMENT TECHNIQUES - ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST |
| NEMA SM 23-1991 (R1997, R2002) | STEAM TURBINES FOR MECHANICAL DRIVE SERVICE |
| API 614 : 2008 | LUBRICATION, SHAFT-SEALING AND OIL-CONTROL SYSTEMS AND AUXILIARIES |
| ASME B31.3:2016 | PROCESS PIPING |
| IEC 61000-4-4:2012 RLV | Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test |
| ISO 1940-1:2003 | Mechanical vibration Balance quality requirements for rotors in a constant (rigid) state Part 1: Specification and verification of balance tolerances |
| ISO 9329-4:1997 | Seamless steel tubes for pressure purposes — Technical delivery conditions — Part 4: Austenitic stainless steels |
| ISO 281:2007 | Rolling bearings Dynamic load ratings and rating life |
| ISO 1217:2009 | Displacement compressors Acceptance tests |
| ISO 262:1998 | ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts |
| API 670 : 2014 | MACHINERY PROTECTION SYSTEMS |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| ISO 9329-2:1997 | Seamless steel tubes for pressure purposes — Technical delivery conditions — Part 2: Unalloyed and alloyed steels with specified elevated temperature properties |
| EN 55022:2010/AC:2011 | INFORMATION TECHNOLOGY EQUIPMENT - RADIO DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT (CISPR 22:2008) |
| ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 1: General principles and requirements |
| IEC 61000-4-2:2008 | Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
| IEC 61000-4-3:2006+AMD1:2007+AMD2:2010 CSV | Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test |
| ISO 7005-1:2011 | Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems |
| ISO 10441:2007 | Petroleum, petrochemical and natural gas industries Flexible couplings for mechanical power transmission Special-purpose applications |
| IEC 60060-1:2010 | High-voltage test techniques - Part 1: General definitions and test requirements |
| API 619 : 2010 | ROTARY-TYPE POSITIVE DISPLACEMENT COMPRESSORS FOR PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES |
| ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.