Customer Support: +1 416-401-8730

Login to i2i Subscription Intertek.com
  • There are no items in your cart
Please enter a keyword to search
Advanced search
Home
CEN
EN ISO 10441:2007

EN ISO 10441:2007

Current

Current

The latest, up-to-date edition.

Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical power transmission - Special-purpose applications (ISO 10441:2007)

Published date

03-15-2007

Publisher

Comite Europeen de Normalisation

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Statutory requirements
5 Coupling selection
6 Coupling design
7 Coupling ratings
8 Coupling requirements
   8.1 Metallic flexible-element couplings
   8.2 Machining
   8.3 Spacer
   8.4 Hub type
   8.5 Integral flanges
   8.6 Hubs
   8.7 Solo plate (idling adapter)
   8.8 Moment simulator
   8.9 Component fit tolerances and potential
        unbalance calculations
   8.10 Fasteners (including studs)
   8.11 Electrical insulation
   8.12 Dynamics
9 Balance
   9.1 General
   9.2 Balancing methods
   9.3 Balance criteria
   9.4 Trim balance holes
10 Materials
11 Accessories
12 Manufacturing quality, inspection, testing and
   preparation for shipment
   12.1 Manufacturing quality
   12.2 Inspection and testing
   12.3 Inspection
   12.4 Testing
   12.5 Preparation for shipment
13 Vendor data
   13.1 General
   13.2 Proposals and contract data
Annex A (normative) Torsional damping couplings
        and resilient couplings
Annex B (normative) Gear couplings
Annex C (normative) Quill-shaft couplings
Annex D (informative) Factors for metallic element
        couplings
Annex E (informative) Example of the determination
        of potential unbalance
Annex F (informative) Examples of misalignments
Annex G (informative) Coupling tapers
Annex H (normative) Coupling guards
Annex I (informative) Procedure for residual unbalance
        check
Annex J (informative) Coupling datasheets
Bibliography

ISO 10441-2007 specifies the requirements for couplings for the transmission of power between the rotating shafts of two machines in special-purpose applications in the petroleum, petrochemical and natural gas industries. Such applications are typically in large and/or high speed machines, in services that can be required to operate continuously for extended periods, are often unspared and are critical to the continued operation of the installation. By agreement, it can be used for other applications or services.Couplings covered by ISO 10441-2007 are designed to accommodate parallel (or lateral) offset, angular misalignment and axial displacement of the shafts without imposing unacceptable mechanical loading on the coupled machines. It is applicable to gear, metallic flexible element, quill shaft and torsionally resilient type couplings.ISO 10441-2007 covers the design, materials of construction, manufacturing quality, inspection and testing of special-purpose couplings.ISO 10441-2007 does not define criteria for the selection of coupling types for specific applications.ISO 10441-2007 is not applicable to other types of couplings, such as clutch, hydraulic, eddy-current, rigid, radial spline, chain and bellows types.

Committee
CEN/TC 12
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current

I.S. EN ISO 10439:2002 PETROLEUM, CHEMICAL AND GAS SERVICE INDUSTRIES - CENTRIFUGAL COMPRESSORS
ISO 13631:2002 Petroleum and natural gas industries Packaged reciprocating gas compressors
BS EN ISO 13691:2002 Petroleum and natural gas industries. High-speed special-purpose gear units
ISO 13691:2001 Petroleum and natural gas industries — High-speed special-purpose gear units
EN ISO 13691:2002 Petroleum and natural gas industries - High-speed special-purpose gear units (ISO 13691:2001)
EN ISO 13631:2002 Petroleum and natural gas industries - Packaged reciprocating gas compressors (ISO 13631:2002)
BS EN ISO 13631:2002 Petroleum and natural gas industries. Packaged reciprocating gas compressors

AGMA 9002 : B BORES AND KEYWAYS FOR FLEXIBLE COUPLINGS (INCH SERIES)
AGMA 9104 : A FLEXIBLE COUPLINGS - MASS ELASTIC PROPERTIES AND OTHER CHARACTERISTICS (METRIC EDITION)
AGMA 9004 : A FLEXIBLE COUPLINGS - MASS ELASTIC PROPERTIES AND OTHER CHARACTERISTICS
SAE J 429 : 2014 MECHANICAL AND MATERIAL REQUIREMENTS FOR EXTERNALLY THREADED FASTENERS
DIN 7190:2001-02 INTERFERENCE FITS - CALCULATION AND DESIGN RULES
ISO 1940-1:2003 Mechanical vibration Balance quality requirements for rotors in a constant (rigid) state Part 1: Specification and verification of balance tolerances
ISO 262:1998 ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts
ISO 2491:1974 Thin parallel keys and their corresponding keyways (Dimensions in millimetres)
AGMA 9112 : A BORES AND KEYWAYS FOR FLEXIBLE COUPLINGS (METRIC SERIES)
EN 953:1997+A1:2009 Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards
ISO 286-2:2010 Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
AGMA 9000 : C FLEXIBLE COUPLINGS - POTENTIAL UNBALANCE CLASSIFICATION
AGMA 9003 : B FLEXIBLE COUPLINGS - KEYLESS FITS

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us