• There are no items in your cart

EN ISO 14978:2006/AC:2008

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - GENERAL CONCEPTS AND REQUIREMENTS FOR GPS MEASURING EQUIPMENT
Superseded date

06-30-2019

Published date

04-02-2008

Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Abbreviations
5 Design characteristics
  5.1 General
  5.2 Indicating measuring equipment
  5.3 Material measures
6 Metrological characteristics
  6.1 General
  6.2 Identification, definition and choice of metrological
      characteristics
  6.3 Indicating measuring equipment - identification of
      general metrological characteristics
  6.4 Material measures - Identification of general
      metrological characteristics
7 Types of presentation and types of specifications for
  characteristics
  7.1 General
  7.2 Presentation of characteristic curves - Fixed and
      floating zero
  7.3 Presentation of a characteristic - Statistical
  7.4 Specifications for single-value metrological
      characteristics
  7.5 Specification for metrological characteristics
      defined in a range
  7.6 Specification for metrological characteristics defined
      in a two- or three-dimensional range
8 Calibration of metrological characteristics
  8.1 Manufacturer and supplier of measuring instruments
  8.2 User of measuring instruments
  8.3 Measurement uncertainty
9 Marking
Annex A (normative) - General minimum requirements and
        guidance for clauses in GPS standards for
        specific measuring equipment
Annex B (informative) - Data sheet for measuring equipment
        requirements
Annex C (normative) - Relation to the GPS matrix model
Bibliography

Describes the general requirements, terms and definitions of characteristics of simple GPS measuring equipment, e.g. micrometers, dial gauges, callipers, surface plates, height gauges, gauge blocks, but not necessarily excluding more complicated equipment.

Committee
TC 290
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

ISO/TR 14638:1995 Geometrical product specification (GPS) Masterplan
ISO/TS 17450-2:2002 Geometrical product specifications (GPS) General concepts Part 2: Basic tenets, specifications, operators and uncertainties
ISO 12179:2000 Geometrical Product Specifications (GPS) Surface texture: Profile method Calibration of contact (stylus) instruments
ISO 5459:2011 Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems
ISO/TS 14253-2:1999 Geometrical Product Specifications (GPS) Inspection by measurement of workpieces and measuring equipment Part 2: Guide to the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification
ISO 2692:2014 Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR)
ISO 1101:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
ISO 1:2016 Geometrical product specifications (GPS) Standard reference temperature for the specification of geometrical and dimensional properties
ISO 14253-1:2017 Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications
ISO 8062-3:2007 Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings
ISO 3650:1998 Geometrical Product Specifications (GPS) Length standards Gauge blocks
ISO/TR 16015:2003 Geometrical product specifications (GPS) — Systematic errors and contributions to measurement uncertainty of length measurement due to thermal influences

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.