• There are no items in your cart

EN ISO 25762:2012

Current
Current

The latest, up-to-date edition.

Plastics - Guidance on the assessment of the fire characteristics and fire performance of fibre-reinforced polymer composites (ISO 25762:2009)
Published date

01-25-2012

Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and abbreviated terms
4 Fibre reinforcement
5 Fire characteristics
6 Fire test methods
Annex A (informative) - Heat release measurements
        on FRP composites
Annex B (informative) - Typical results given for
        glass-fibre-reinforced polymer composites
        by ISO and EN fire test methods
Annex C (informative) - Recommendations for the
        handling and storage of fibre-reinforced
        polymer composites
Annex D (informative) - Procedure in the event of
        fire involving fibre-reinforced polymer
        composites
Annex E (informative) - Mounting and fixing of
        test specimens of fibre-reinforced polymer
        composites
Bibliography

ISO 25762:2009 gives guidelines for the assessment of the fire characteristics and fire performance of fibre-reinforced polymer (FRP) composites, particularly in structural applications in buildings and transport.It is applicable to FRP composites prepared from thermosetting or thermoplastic resins and reinforced with inorganic fibres greater than 7,5 mm in length.It gives guidelines on:the applicability of product types (e.g. sheets, laminates, profiled sections and some sandwich constructions) to end-use performance;the test methods and performance criteria for different physical forms of FRP test specimen.

Committee
CEN/TC 249
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current

ISO 5660-1:2015 Reaction-to-fire tests Heat release, smoke production and mass loss rate Part 1: Heat release rate (cone calorimeter method) and smoke production rate (dynamic measurement)
ISO 1268-1:2001 Fibre-reinforced plastics Methods of producing test plates Part 1: General conditions
ISO 5658-2:2006 Reaction to fire tests Spread of flame Part 2: Lateral spread on building and transport products in vertical configuration
ISO 13784-2:2002 Reaction-to-fire tests for sandwich panel building systems Part 2: Test method for large rooms
ISO 10093:1998 Plastics Fire tests Standard ignition sources
ISO 9705:1993 Fire tests Full-scale room test for surface products
ISO 1716:2010 Reaction to fire tests for products Determination of the gross heat of combustion (calorific value)
ISO 16312-1:2016 Guidance for assessing the validity of physical fire models for obtaining fire effluent toxicity data for fire hazard and risk assessment Part 1: Criteria
ISO 5659-2:2017 Plastics — Smoke generation — Part 2: Determination of optical density by a single-chamber test
ISO 5660-2:2002 Reaction-to-fire tests Heat release, smoke production and mass loss rate Part 2: Smoke production rate (dynamic measurement)
ISO 1268-4:2005 Fibre-reinforced plastics Methods of producing test plates Part 4: Moulding of prepregs
ISO 11925-2:2010 Reaction to fire tests Ignitability of products subjected to direct impingement of flame Part 2: Single-flame source test
ISO 1268-7:2001 Fibre-reinforced plastics Methods of producing test plates Part 7: Resin transfer moulding
ISO 13943:2017 Fire safety — Vocabulary
ISO 24473:2008 Fire tests — Open calorimetry — Measurement of the rate of production of heat and combustion products for fires of up to 40 MW
EN 13238:2010 Reaction to fire tests for building products - Conditioning procedures and general rules for selection of substrates
ISO 13785-2:2002 Reaction-to-fire tests for faades Part 2: Large-scale test
ISO 1182:2010 Reaction to fire tests for products Non-combustibility test
EN 13823:2010+A1:2014 REACTION TO FIRE TESTS FOR BUILDING PRODUCTS - BUILDING PRODUCTS EXCLUDING FLOORINGS EXPOSED TO THE THERMAL ATTACK BY A SINGLE BURNING ITEM
ISO/TS 5658-1:2006 Reaction to fire tests — Spread of flame — Part 1: Guidance on flame spread
ISO 1268-6:2002 Fibre-reinforced plastics — Methods of producing test plates — Part 6: Pultrusion moulding
ISO 1268-10:2005 Fibre-reinforced plastics — Methods of producing test plates — Part 10: Injection moulding of BMC and other long-fibre moulding compounds — General principles and moulding of multipurpose test specimens
ISO/TR 9705-2:2001 Reaction-to-fire tests Full-scale room tests for surface products Part 2: Technical background and guidance
ISO 1268-8:2004 Fibre-reinforced plastics — Methods of producing test plates — Part 8: Compression moulding of SMC and BMC
ISO 472:2013 Plastics Vocabulary
ISO 10840:2008 Plastics Guidance for the use of standard fire tests
ISO 1268-2:2001 Fibre-reinforced plastics Methods of producing test plates Part 2: Contact and spray-up moulding
ISO 15791-1:2014 Plastics Development and use of intermediate-scale fire tests for plastics products Part 1: General guidance
ISO/TR 5660-3:2003 Reaction-to-fire tests Heat release, smoke production and mass loss rate Part 3: Guidance on measurement
ISO 14696:2009 Reaction-to-fire tests Determination of fire and thermal parameters of materials, products and assemblies using an intermediate-scale calorimeter (ICAL)
ISO 13571:2012 Life-threatening components of fire Guidelines for the estimation of time to compromised tenability in fires
ISO 19706:2011 Guidelines for assessing the fire threat to people
ISO/TR 16312-2:2007 Guidance for assessing the validity of physical fire models for obtaining fire effluent toxicity data for fire hazard and risk assessment Part 2: Evaluation of individual physical fire models
CEN/TS 15447:2006 Mounting and fixing in reaction to fire tests under the Construction Products Directive
ISO 13784-1:2014 Reaction to fire test for sandwich panel building systems — Part 1: Small room test
ISO 9239-1:2010 Reaction to fire tests for floorings Part 1: Determination of the burning behaviour using a radiant heat source
ISO 1268-5:2001 Fibre-reinforced plastics Methods of producing test plates Part 5: Filament winding
ISO 21367:2007 Plastics — Reaction to fire — Test method for flame spread and combustion product release from vertically oriented specimens
ISO 1268-11:2005 Fibre-reinforced plastics — Methods of producing test plates — Part 11: Injection moulding of BMC and other long-fibre moulding compounds — Small plates
ISO 13927:2015 Plastics — Simple heat release test using a conical radiant heater and a thermopile detector
ISO 14697:2007 Reaction-to-fire tests — Guidance on the choice of substrates for building and transport products
ISO 1268-9:2003 Fibre-reinforced plastics — Methods of producing test plates — Part 9: Moulding of GMT/STC
ISO 1268-3:2000 Fibre-reinforced plastics Methods of producing test plates Part 3: Wet compression moulding

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.