Customer Support: +1 416-401-8730

Login to i2i Subscription Intertek.com
  • There are no items in your cart
Please enter a keyword to search
Advanced search

EN ISO 9093-2:2002

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Small craft - Seacocks and through-hull fittings - Part 2: Non-metallic (ISO 9093-2:2002)
Superseded date

04-18-2019

Published date

10-15-2002

Publisher

Comite Europeen de Normalisation

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Material requirements
5 Thread
6 Through-hull fittings - Requirements
7 Seacocks - Requirements
8 Hose fittings - Requirements
9 Drain plugs - Requirements
10 Installation
11 Manufacturers installation information
12 Owner's manual
13 Service manual
Annex A (normative) Strength test
Bibliography
Annex ZA (normative) Normative references to international
                       publications with their relevant
                       European publications
Annex ZB (informative) Clauses of this European Standard
                       addressing essential requirements or
                       other provisions of EU Directives

ISO 9093-2:2002 specifies requirements for the manufacture and installation of non-metallic through-hull fittings and/or assemblies comprising through-hull fittings, seacocks, hose fittings and/or drain plugs and components attached thereto, used in small craft of up to 24 m length of hull. ISO 9093-2:2002 is not applicable to engine exhaust fittings and sail drive through-hull connections.

DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

ISO 15083:2003 Small craft - Bilge-pumping systems
I.S. EN ISO 15083:2003 SMALL CRAFT - BILGE-PUMPING SYSTEMS
EN ISO 15083:2003 Small craft - Bilge-pumping systems (ISO 15083:2003)
BS EN ISO 15083:2003 Small craft. Bilge-pumping systems
DIN EN ISO 15083:2003-06 SMALL CRAFT - BILGE PUMPING SYSTEMS

ISO 75-1:2013 Plastics Determination of temperature of deflection under load Part 1: General test method
EN ISO 180:2000/A2:2013 PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH (ISO 180:2000/AMD 2:2013)
ISO 527-4:1997 Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
EN ISO 527-4:1997 PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 4: TEST CONDITIONS FOR ISOTROPIC AND ORTHOTROPIC FIBRE-REINFORCED PLASTIC COMPOSITES
EN ISO 527-2:2012 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012)
1994/25/EC : 1994 DIRECTIVE 94/25/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 16 JUNE 1994 ON THE APPROXIMATION OF THE LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO RECREATIONAL CRAFT
EN ISO 178:2010/A1:2013 PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010/AMD 1:2013)
ISO 8666:2016 Small craft Principal data
EN ISO 527-1:2012 Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012)
ISO 75-2:2013 Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
ISO 527-5:2009 Plastics Determination of tensile properties Part 5: Test conditions for unidirectional fibre-reinforced plastic composites
ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation
ISO 180:2000 Plastics Determination of Izod impact strength
EN ISO 527-5:2009 Plastics - Determination of tensile properties - Part 5: Test conditions for unidirectional fibre-reinforced plastic composites (ISO 527-5:2009)
ISO 75-3:2004 Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics
ISO 527-3:1995 Plastics Determination of tensile properties Part 3: Test conditions for films and sheets
ISO 178:2010 Plastics Determination of flexural properties
EN ISO 527-3:1995/AC:2002 PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 3: TEST CONDITIONS FOR FILMS AND SHEETS
ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us