• There are no items in your cart

I.S. EN 10002-1:2001

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE
Available format(s)

Hardcopy , PDF

Superseded date

09-21-2009

Language(s)

English

Published date

01-01-2001

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

Foreword
1 Scope
2 Normative references
3 Principle
4 Definitions
5 Symbols and designations
6 Test piece
   6.1 Shape and dimensions
   6.2 Types
   6.3 Preparation of test pieces
7 Determination of original cross-sectional area (S[O])
8 Marking the original gauge length (L[O])
9 Accuracy of testing apparatus
10 Conditions of testing
   10.1 Method of gripping
   10.2 Test rate
11 Determination of percentage elongation after fracture (A)
12 Determination of the percentage total elongation at maximum
   force (A[gt])
13 Determination of proof strength, non proportional
   extension (R[p])
14 Determination of proof strength, total extension (R[t])
15 Method of verification of permanent set strength (R[r])
16 Determination of percentage reduction of area (Z)
17 Test report
Annex A (informative) Recommendations concerning the use of
        computer controlled tensile testing machine
Annex B (normative) Types of test pieces to be used for thin
        products: sheets, strips and flats between 0,1 mm and 3
        mm thick
Annex C (normative) Types of test pieces to be used for wire, bars
        and sections with a diameter or thickness of less than 4 mm
Annex D (normative) Types of test pieces to be used for sheets
        and flats of thickness equal to or greater than 3 mm, and
        wire, bars and sections of diameter or thickness equal to
        or greater than 4 mm
Annex E (normative) Types of test pieces to be used for tubes
Annex F (informative) Measuring the percentage elongation after
        fracture if the specified value is less than 5%
Annex G (informative) Measurement of percentage elongation after
        fracture based on subdivision of the original gauge length
Annex H (informative) Manual method of determination
        of the percentage total elongation at maximum force
        for long products such as bars, wire, rods
Annex J (informative) Precision of tensile testing and estimation
        of the uncertainty of measurement
Bibliography

Defines the method for tensile testing of metallic materials and describes the mechanical properties which can be determined at ambient temperature.

DocumentType
Standard
Pages
58
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy

Standards Relationship
SN EN 10002-1 : 2001 Identical
BS EN 10002-1:2001 Identical
NEN EN 10002-1 : 2001 Identical
NS EN 10002-1 : 2001 Identical
DIN EN 10002-1:2001-12 Identical
EN 10002-1 : 2001 Identical
UNI EN 10002-1 : 2004 Identical
NF EN 10002-1 : 2001 Identical
UNE-EN 10002-1:2002 Identical
NBN EN 10002-1 : 2002 Identical

ISO/TTA 2:1997 Tensile tests for discontinuously reinforced metal matrix composites at ambient temperatures
EN 20286-2 : 1993 ISO SYSTEM OF LIMITS AND FITS - TABLES OF STANDARD TOLERANCE GRADES AND LIMIT DEVIATIONS FOR HOLES AND SHAFTS
EN ISO 377:2017 Steel and steel products - Location and preparation of samples and test pieces for mechanical testing (ISO 377:2017)
ISO 2566-2:1984 Steel Conversion of elongation values Part 2: Austenitic steels
ISO 6892:1998 Metallic materials Tensile testing at ambient temperature
EN ISO 2566-1:1999 Steel - Conversion of elongation values - Part 1: Carbon and low alloy steels (ISO 2566-1:1984)
ISO 2566-1:1984 Steel Conversion of elongation values Part 1: Carbon and low alloy steels
EN ISO 2566-2:1999 Steel - Conversion of elongation values - Part 2: Austenitic steels (ISO 2566-2:1984)
ISO 286-2:2010 Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
EN 10002-4 : 1994 METALLIC MATERIALS - TENSILE TEST - VERIFICATION OF EXTENSOMETERS USED IN UNIAXIAL TESTING
ISO 7500-1:2015 Metallic materials Calibration and verification of static uniaxial testing machines Part 1: Tension/compression testing machines Calibration and verification of the force-measuring system
ISO 377:2017 Steel and steel products — Location and preparation of samples and test pieces for mechanical testing
EN 10291 : 2000 METALLIC MATERIALS - UNIAXIAL CREEP TESTING IN TENSION - METHOD OF TEST

View more information
US$100.85
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.