• There are no items in your cart

I.S. EN 1123-2:2006

Withdrawn
Withdrawn

A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

PIPES AND FITTINGS OF LONGITUDINALLY WELDED HOT-DIP GALVANIZED STEEL TUBE WITH SPIGOT AND SOCKET FOR WASTE WATER SYSTEMS - PART 2: DIMENSIONS
Available format(s)

Hardcopy , PDF

Withdrawn date

10-22-2007

Language(s)

English

Published date

01-24-2007

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviations
5 Dimensions
  5.1 General and tolerances
  5.2 Sockets
  5.3 Pipes
       5.3.1 General
       5.3.2 Pipe with one socket - Shape B 1
       5.3.3 Pipe with two sockets - Shape B 2
  5.4 Bends
       5.4.1 General
       5.4.2 Bend with large radius - Shape C 1
       5.4.3 Bend with small radius - Shape C 2
       5.4.4 Bend with stilling section - Shape C 3
       5.4.5 Offset pipe - Shape C 4
  5.5 Branches
       5.5.1 General
       5.5.2 Single branch - Shape D 1
       5.5.3 Reducing single branch - Shape D 11
       5.5.4 Reducing double branch - Shape D 21
       5.5.5 Reducing angular branch - Shape D 31
       5.5.6 Single transition branch - Shape D 12
  5.6 Connections
       5.6.1 General
       5.6.2 Connecting units for use with discharge sets of
             sanitary appliances
       5.6.3 Connecting units for use with other kinds of pipes
  5.7 Transition pipes
       5.7.1 General
       5.7.2 Transition pipe (eccentric) - Shape F 1
       5.7.3 Transition pipe (concentric) - Shape F 2
       5.7.4 Transition pipe (concentric) with extended spigot -
             Shape F 3
       5.7.5 Straight coupling - Shape F 4
       5.7.6 Insertion coupling with long socket - Shape F 5
  5.8 Traps
       5.8.1 P-trap - Shape G 1
       5.8.2 S-trap - Shape G 2
       5.8.3 Pipe bridge (V-trap) - Shape G 3
       5.8.4 Rainpipe trap (type A) - Shape G 4
       5.8.5 Rainpipe trap - Shape G 5
  5.9 Access pipes
       5.9.1 Access pipe with round cleaning hole - Shape H 1
       5.9.2 Access pipe with rectangular cleaning hole -
             Shape H 2 or with oval cleaning hole - Shape H 3
  5.10 Other fittings
6 Accessories
  6.1 Shear coupling
       6.1.1 Shear coupling A - Shape K 1
       6.1.2 Shear coupling B - Shape K 2
       6.1.3 Shear coupling with release - Shape K 3
       6.1.4 Shear coupling C - Shape K 4
  6.2 Plug
       6.2.1 Plug - Shape K 10
       6.2.2 Plug with extended spigot - Shape K 11
       6.2.3 Plug with screw top - Shape K 12
7 Seals
  7.1 General
  7.2 Seal for DN 40 to DN 200 - Shape M 1
  7.3 Seals - Shape M 2 for DN 250 and DN 300
  7.4 Elastomeric pressure ring for DN 250 and DN 300 - Shape M 3
  7.5 Transition seal from steel pipe special socket to
       plastic discharge pipe - Shape E 12 D
  7.6 Gasket for round cleaning hole in access pipes of
       shape H 1 - Shape H 1 D
  7.7 Gasket for rectangular cleaning hole - Shape H 2 D
       and gasket for oval cleaning hole - Shape H 3 D

Describes dimensions and tolerances for pipes, fittings, pipe connectors and seals and establishes a system of designations for the different pipe and fitting types that conform to the stated requirements.

DevelopmentNote
2006 Edition Re-Issued in October 2007 & incorporates AMD 1 2007. (11/2007)
DocumentType
Standard
Pages
63
PublisherName
National Standards Authority of Ireland
Status
Withdrawn
Supersedes

EN 877:1999/A1:2006/AC:2008 CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE
EN 1566-1:1998 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: Specifications for pipes, fittings and the system
EN 1453-1:2017/AC:2017 PLASTICS PIPING SYSTEMS WITH STRUCTURED-WALL PIPES FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) INSIDE BUILDINGS - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPES AND THE SYSTEM
EN 1455-1:1999 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 1: Requirements for pipes, fittings and the system
EN 1519-1:1999 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system
EN 1123-1:1999/A1:2004 PIPES AND FITTINGS OF LONGITUDINALLY WELDED HOT-DIP GALVANIZED STEEL PIPES WITH SPIGOT AND SOCKET FOR WASTE WATER SYSTEMS - PART 1: REQUIREMENTS, TESTING, QUALITY CONTROL
EN 1565-1:1998 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN+PVC) - Part 1: Specifications for pipes, fittings and the system

View more information
US$108.53
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.