GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 16 BAR - PART 2: SPECIFIC FUNCTIONAL REQUIREMENTS FOR POLYETHYLENE (MOP UP TO AND INCLUDING 10 BAR)

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-01-2012

Publisher

National Standards Authority of Ireland

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

Foreword
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviations
4 Design
5 Construction
6 Quality control
7 Pressure testing
Annex A (informative) - Storage, handling and
transportation
Annex B (informative) - Fusion joint integrity
Annex C (informative) - Technical changes between this
European Standard and EN 12007-2:2000
Bibliography

Explains the specific functional requirements for polyethylene (PE) pipelines in addition to the general functional requirements of EN 12007-1 for: a) a maximum operating pressure (MOP) up to and including 10 bar; b) an operating temperature between -20 degrees C and +40 degrees C.

DocumentType	Standard
Pages	31
PublisherName	National Standards Authority of Ireland
Status	Current
Supersedes	I.S. EN 12007-2:2000

Standards	Relationship
DIN EN 12007-2:2012-10	Identical
UNE-EN 12007-2:2013	Identical
SN EN 12007-2:2012	Identical
NF EN 12007-2 : 2012	Identical
NBN EN 12007-2 : 2012	Identical
UNI EN 12007-2 : 2012	Identical
NS EN 12007-2 : 2012	Identical
BS EN 12007-2:2012	Identical
NEN EN 12007-2 : 2012	Identical
EN 12007-2:2012	Identical

I.S. 329:2015	GAS DISTRIBUTION MAINS (EDITION 3)
I.S. 820:2010	NON-DOMESTIC GAS INSTALLATIONS

EN 12327:2012	Gas infrastructure - Pressure testing, commissioning and decommissioning procedures - Functional requirements
EN 1555-1:2010	Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General
EN 1555-3:2010+A1:2012	Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings
EN 12007-3:2015	Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 3: Specific functional requirements for steel
EN 12007-1:2012	Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 1: General functional requirements
ISO 10838-2:2000	Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 2: Metal fittings for pipes of nominal outside diameter greater than 63 mm
ISO 21307:2011	Plastics pipes and fittings Butt fusion jointing procedures for polyethylene (PE) pipes and fittings used in the construction of gas and water distribution systems
ISO 10838-1:2000	Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 1: Metal fittings for pipes of nominal outside diameter less than or equal to 63 mm
ISO 12176-1:2017	Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion
ISO 3:1973	Preferred numbers Series of preferred numbers
ISO 12176-2:2008	Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2: Electrofusion
ISO 11414:2009	Plastics pipes and fittings Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion
EN 1555-4:2011	Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 4: Valves
EN 1555-5:2010	Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system
EN 1555-2:2010	Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes
ISO 497:1973	Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers
EN 12007-4:2012	Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 4: Specific functional requirements for renovation
ISO 11413:2008	Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting

View more information

US$58.10

Excluding Tax where applicable

Product format

I agree to the DRM document license rules apply against the PDF selection made.

Please confirm that you agree to the document license rules for this document.

I agree to the document license rules .

Please confirm that you agree to the document license rules for this document.

Access your standards online with a subscription

Features

Simple online access to standards, technical information and regulations.
Critical updates of standards and customisable alerts and notifications.
Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

Get in touch with us

Log into your Account

I.S. EN 12007-2:2012

Current

Table of Contents

Abstract

General Product Information

International Equivalents

Standards Referenced By This Book

Standards Referencing This Book

Category

Subcategory

Access your standards online with a subscription