• There are no items in your cart

I.S. EN 12079-1:2006

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

OFFSHORE CONTAINERS AND ASSOCIATED LIFTING SETS - PART 1: OFFSHORE CONTAINERS - DESIGN, MANUFACTURE AND MARKING
Available format(s)

Hardcopy , PDF

Superseded date

07-23-2013

Language(s)

English

Published date

01-01-2006

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Design
   5.1 General
   5.2 Structural strength
   5.3 Welding
   5.4 Additional design details
   5.5 Tank containers
   5.6 Containers for bulk solids
6 Materials
   6.1 Steel - General
   6.2 Rolled and extruded steels in offshore container
       structures
   6.3 Aluminium
   6.4 Non-metallic materials
   6.5 Material certificates
7 Type testing
   7.1 General
   7.2 Test equipment and calibration
   7.3 Lifting test
   7.4 Vertical impact test
   7.5 Other tests
8 Production
   8.1 General
   8.2 Primary structure
   8.3 Secondary structure
   8.4 Production testing
   8.5 Failure of production containers
9 Marking
   9.1 Safety marking
   9.2 Identification markings
   9.3 Information markings
   9.4 Other markings
10 Container Data Plate
   10.1 General
   10.2 Contents of Data Plate
11 Certificate of conformity
   11.1 General
   11.2 Documentation
   11.3 Contents of the certificate of conformity
Annex A (Informative) Certification Requirements for
        Containers
Bibliography

States requirements for the design, manufacture and marking of offshore freight and service containers with maximum gross mass not exceeding 25000 kg, intended for repeated use to, from and between offshore installations and ships.

DevelopmentNote
Together with I.S. EN 12079-3 supersedes I.S. EN 12079. (07/2006)
DocumentType
Standard
Pages
36
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy
Supersedes

EN 10002-1 : 2001 METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE
EN ISO 5817:2014 Welding - Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) - Quality levels for imperfections (ISO 5817:2014)
ISO 209-1:1989 Wrought aluminium and aluminium alloys Chemical composition and forms of products Part 1: Chemical composition
ISO 9606-2:2004 Qualification test of welders — Fusion welding — Part 2: Aluminium and aluminium alloys
EN 10025-4:2004 Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
ISO 1496-1:2013 Series 1 freight containers — Specification and testing — Part 1: General cargo containers for general purposes
EN 30042 : 1994 ARC WELDED JOINTS IN ALUMINIUM AND ITS WELDABLE ALLOYS - GUIDANCE ON QUALITY LEVELS FOR IMPERFECTIONS
ISO 10042:2005 Welding Arc-welded joints in aluminium and its alloys Quality levels for imperfections
ISO 15614-2:2005 Specification and qualification of welding procedures for metallic materials Welding procedure test Part 2: Arc welding of aluminium and its alloys
EN 10164:2004 Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions
EN 1714:1997/A2:2003 NON-DESTRUCTIVE TESTING OF WELDS - ULTRASONIC TESTING OF WELDED JOINTS
EN 1011-1:2009 Welding - Recommendations for welding of metallic materials - Part 1: General guidance for arc welding
EN 10025-1:2004 Hot rolled products of structural steels - Part 1: General technical delivery conditions
EN 473:2008 Non-destructive testing - Qualification and certification of NDT personnel - General principles
EN 10210-1:2006 Hot finished structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions
EN 1011-2:2001/A1:2003 WELDING - RECOMMENDATIONS FOR WELDING OF METALLIC MATERIALS - PART 2: ARC WELDING OF FERRITIC STEELS
EN 10045-1 : 1990 METALLIC MATERIALS - CHARPY IMPACT TEST - PART 1: TEST METHOD
ISO 5817:2014 Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections
EN 12079-3 : 2006 OFFSHORE CONTAINERS AND ASSOCIATED LIFTING SETS - PART 3: PERIODIC INSPECTION, EXAMINATION AND TESTING
ISO 15614-1:2017 Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys
ISO 15609-1:2004 Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 1: Arc welding
EN 10219-1:2006 Cold formed welded structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
EN 1289:1998/A2:2003 NON-DESTRUCTIVE TESTING OF WELDS - PENETRANT TESTING OF WELDS - ACCEPTANCE LEVELS
EN ISO 15614-2:2005 Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 2: Arc welding of aluminium and its alloys (ISO 15614-2:2005)
ISO 1496-3:1995 Series 1 freight containers Specification and testing Part 3: Tank containers for liquids, gases and pressurized dry bulk
EN ISO 9606-2:2004 Qualification test of welders - Fusion welding - Part 2: Aluminium and aluminium alloys (ISO 9606-2:2004)
EN 10250-2:1999 Open die steel forgings for general engineering purposes - Part 2: Non-alloy quality and special steels
ISO 668:2013 Series 1 freight containers Classification, dimensions and ratings
EN 10204:2004 Metallic products - Types of inspection documents
EN 10025-2:2004/AC:2005 HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR NON-ALLOY STRUCTURAL STEELS
ISO 9001:2015 Quality management systems — Requirements
EN ISO 15609-1:2004 Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 1: Arc welding (ISO 15609-1:2004)
ISO 1496-4:1991 Series 1 freight containers — Specification and testing — Part 4: Non-pressurized containers for dry bulk
EN 1712:1997/A2:2004 NON-DESTRUCTIVE TESTING OF WELDS - ULTRASONIC TESTING OF WELDED JOINTS - ACCEPTANCE LEVELS
EN 12079-2 : 2006 OFFSHORE CONTAINERS AND ASSOCIATED LIFTING SETS - PART 2: LIFTING SETS - DESIGN, MANUFACTURE AND MARKING
ISO 7500-1:2015 Metallic materials Calibration and verification of static uniaxial testing machines Part 1: Tension/compression testing machines Calibration and verification of the force-measuring system
EN 12517-1:2006 Non-destructive testing of welds - Part 1: Evaluation of welded joints in steel, nickel, titanium and their alloys by radiography - Acceptance levels
EN 1291:1998/A2:2003 NON-DESTRUCTIVE TESTING OF WELDS - MAGNETIC PARTICLE TESTING OF WELDS - ACCEPTANCE LEVELS
ISO 15607:2003 Specification and qualification of welding procedures for metallic materials General rules
EN 571-1:1997 Non destructive testing - Penetrant testing - Part 1: General principles
EN 970:1997 Non-destructive examination of fusion welds - Visual examination
EN 1290:1998/A2:2003 NON-DESTRUCTIVE EXAMINATION OF WELDS - MAGNETIC PARTICLE EXAMINATION OF WELDS
EN 10025-3:2004 Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels
EN 10250-3:1999 Open die steel forgings for general engineering purposes - Part 3: Alloy special steels
EN 1435:1997/A2:2003 NON-DESTRUCTIVE TESTING OF WELDS - RADIOGRAPHIC TESTING OF WELDED JOINTS
EN ISO 15607:2003 Specification and qualification of welding procedures for metallic materials - General rules (ISO 15607:2003)
1994/9/EC : 1994 DIRECTIVE 94/9/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 23 MARCH 1994 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING EQUIPMENT AND PROTECTIVE SYSTEMS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES
ISO 1161:2016 Series 1 freight containers — Corner and intermediate fittings — Specifications
EN 287-1:2011 Qualification test of welders - Fusion welding - Part 1: Steels

View more information
US$70.16
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.