I.S. EN 12952-2:2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
WATER-TUBE BOILERS AND AUXILIARY INSTALLATIONS - PART 2: MATERIALS FOR PRESSURE PARTS OF BOILERS AND ACCESSORIES
Hardcopy , PDF
01-27-2022
English
01-01-2011
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Foreword
1 Scope
2 Normative references
3 General requirements
4 Materials for pressure parts
5 Materials for non-pressure parts
6 Inspection documentation
Annex A (normative) - Materials covered by European
material Standards
Annex B (normative) - Establishment of creep rupture strength
values for new materials
Annex C (normative) - Special requirements for composite
tubes
Annex D (informative) - Significant technical changes between
this European Standard and the previous edition
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of
Directive 97/23/EC
Bibliography
Contains the requirements for the following materials for use in pressure parts of water-tube boilers and for parts welded on pressure parts: - plates; - wrought seamless tubes; - electrically welded tubes; - submerged, plasma and TIG arc-welded tubes; - forgings; - castings; - rolled bars; - welding consumables; - fasteners; - seamless composite tubes.
DocumentType |
Standard
|
Pages |
41
|
PublisherName |
National Standards Authority of Ireland
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
Standards | Relationship |
NEN EN 12952-2 : 2011 | Identical |
NF EN 12952-2 : 2011 | Identical |
EN 12952-2:2011 | Identical |
NBN EN 12952-2 : 2011 | Identical |
SN EN 12952-2 : 2011 | Identical |
UNI EN 12952-2 : 2011 | Identical |
UNE-EN 12952-2:2012 | Identical |
DIN EN 12952-2:2011-10 | Identical |
BS EN 12952-2:2011 | Identical |
NS EN 12952-2 : 2011 | Identical |
ONORM EN 12952-2 : 2011 | Identical |
EN ISO 3580:2017 | Welding consumables - Covered electrodes for manual metal arc welding of creep-resisting steels - Classification (ISO 3580:2017) |
ISO 14341:2010 | Welding consumables Wire electrodes and weld deposits for gas shielded metal arc welding of non alloy and fine grain steels Classification |
EN 10269:2013 | Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties |
ISO 26304:2011 | Welding consumables Solid wire electrodes, tubular cored electrodes and electrode-flux combinations for submerged arc welding of high strength steels Classification |
ISO 3581:2016 | Welding consumables — Covered electrodes for manual metal arc welding of stainless and heat-resisting steels — Classification |
ISO 14343:2017 | Welding consumables — Wire electrodes, strip electrodes, wires and rods for arc welding of stainless and heat resisting steels — Classification |
ISO/IEC 17021:2011 | Conformity assessment Requirements for bodies providing audit and certification of management systems |
ISO 24598:2012 | Welding consumables Solid wire electrodes, tubular cored electrodes and electrode-flux combinations for submerged arc welding of creep-resisting steels Classification |
ISO 17633:2010 | Welding consumables — Tubular cored electrodes and rods for gas shielded and non-gas shielded metal arc welding of stainless and heat-resisting steels — Classification |
EN 10216-5:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 5: Stainless steel tubes |
EN 10213:2007+A1:2016 | Steel castings for pressure purposes |
EN ISO 6892-1:2016 | Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016) |
EN 10028-3:2017 | Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized |
EN 10273:2016 | Hot rolled weldable steel bars for pressure purposes with specified elevated temperature properties |
EN 10228-2:2016 | Non-destructive testing of steel forgings - Part 2: Penetrant testing |
ISO 544:2011 | Welding consumables Technical delivery conditions for filler materials and fluxes Type of product, dimensions, tolerances and markings |
EN ISO 10893-10:2011 | Non-destructive testing of steel tubes - Part 10: Automated full peripheral ultrasonic testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of longitudinal and/or transverse imperfections (ISO 10893-10:2011) |
EN 10164:2004 | Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions |
EN 1759-1:2004 | Flanges and their joint - Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 1: Steel flanges, NPS 1/2 to 24 |
EN ISO 8495:2013 | Metallic materials - Tube - Ring-expanding test (ISO 8495:2013) |
ISO/TR 15608:2017 | Welding Guidelines for a metallic materials grouping system |
EN 1503-2:2000 | Valves - Materials for bodies, bonnets and covers - Part 2: Steels other than those specified in European Standards |
EN ISO 14171:2016 | Welding consumables - Solid wire electrodes, tubular cored electrodes and electrode/flux combinations for submerged arc welding of non alloy and fine grain steels - Classification (ISO 14171:2016) |
ISO 2566-2:1984 | Steel Conversion of elongation values Part 2: Austenitic steels |
ISO 2560:2009 | Welding consumables Covered electrodes for manual metal arc welding of non-alloy and fine grain steels Classification |
EN 10314:2016 | Method for the derivation of minimum values of proof strength of steel at elevated temperatures |
ISO 6892-1:2016 | Metallic materials Tensile testing Part 1: Method of test at room temperature |
EN 12952-3:2011 | Water-tube boilers and auxiliary installations - Part 3: Design and calculation for pressure parts of the boiler |
ISO 18276:2017 | Welding consumables — Tubular cored electrodes for gas-shielded and non-gas-shielded metal arc welding of high strength steels — Classification |
EN 1503-1:2000 | Valves - Materials for bodies, bonnets and covers - Part 1: Steels specified in European Standards |
EN 10254:1999 | Steel closed die forgings - General technical delivery conditions |
EN 12536:2000 | Welding consumables - Rods for gas welding of non alloy and creep-resisting steels - Classification |
EN ISO 16834:2012 | Welding consumables - Wire electrodes, wires, rods and deposits for gas shielded arc welding of high strength steels - Classification (ISO 16834:2012) |
EN ISO 2566-1:1999 | Steel - Conversion of elongation values - Part 1: Carbon and low alloy steels (ISO 2566-1:1984) |
ISO 14344:2010 | Welding consumables — Procurement of filler materials and fluxes |
EN ISO 18276:2017 | Welding consumables - Tubular cored electrodes for gas-shielded and non-gas-shielded metal arc welding of high strength steels - Classification (ISO 18276:2017) |
EN 10216-2:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties |
ISO 3580:2017 | Welding consumables — Covered electrodes for manual metal arc welding of creep-resisting steels — Classification |
EN 764-5:2014 | Pressure equipment - Part 5: Inspection documentation of metallic materials and compliance with the material specification |
EN ISO 21952:2012 | Welding consumables - Wire electrodes, wires, rods and deposits for gas shielded arc welding of creep-resisting steels - Classification (ISO 21952:2012) |
EN 12952-12:2003 | Water-tube boilers and auxiliary installations - Part 12: Requirements for boiler feedwater and boiler water quality |
EN 12952-7:2012 | Water-tube boilers and auxiliary installations - Part 7: Requirements for equipment for the boiler |
EN 10028-2:2017 | Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties |
EN 10228-1:1999 | Non-destructive testing of steel forgings - Part 1: Magnetic particle inspection |
EN 10253-4:2008/AC:2009 | BUTT-WELDING PIPE FITTINGS - PART 4: WROUGHT AUSTENITIC AND AUSTENITIC-FERRITIC (DUPLEX) STAINLESS STEELS WITH SPECIFIC INSPECTION REQUIREMENTS |
EN ISO 17634:2015 | Welding consumables - Tubular cored electrodes for gas shielded metal arc welding of creep-resisting steels - Classification (ISO 17634:2015) |
EN ISO 24598:2012 | Welding consumables - Solid wire electrodes, tubular cored electrodes and electrode-flux combinations for submerged arc welding of creep-resisting steels - Classification (ISO 24598:2012) |
EN 10028-7:2016 | Flat products made of steels for pressure purposes - Part 7: Stainless steels |
ISO 148-1:2016 | Metallic materials — Charpy pendulum impact test — Part 1: Test method |
EN 10308:2001 | Non destructive testing - Ultrasonic testing of steel bars |
EN 10217-7:2014 | Welded steel tubes for pressure purposes - Technical delivery conditions - Part 7: Stainless steel tubes |
ISO 21952:2012 | Welding consumables — Wire electrodes, wires, rods and deposits for gas shielded arc welding of creep-resisting steels — Classification |
ISO 6303:1981 | Pressure vessel steels not included in ISO 2604, Parts 1 to 6 — Derivation of long-time stress rupture properties |
ISO 14171:2016 | Welding consumables Solid wire electrodes, tubular cored electrodes and electrode/flux combinations for submerged arc welding of non alloy and fine grain steels Classification |
ISO 16834:2012 | Welding consumables — Wire electrodes, wires, rods and deposits for gas shielded arc welding of high strength steels — Classification |
EN 10222-3:2017 | Steel forgings for pressure purposes - Part 3: Nickel steels with specified low temperature properties |
EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
EN ISO 14341:2011 | Welding consumables - Wire electrodes and weld deposits for gas shielded metal arc welding of non alloy and fine grain steels - Classification (ISO 14341:2010) |
EN 10222-5:2017 | Steel forgings for pressure purposes - Part 5: Martensitic, austenitic and austenitic-ferritic stainless steels |
EN 10228-3:2016 | Non-destructive testing of steel forgings - Part 3: Ultrasonic testing of ferritic or martensitic steel forgings |
EN 10021:2006 | General technical delivery conditions for steel products |
EN ISO 2560:2009 | Welding consumables - Covered electrodes for manual metal arc welding of non-alloy and fine grain steels - Classification (ISO 2560:2009) |
ISO 2566-1:1984 | Steel Conversion of elongation values Part 1: Carbon and low alloy steels |
EN 10217-2:2002/A1:2005 | WELDED STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 2: ELECTRIC WELDED NON-ALLOY AND ALLOY STEEL TUBES WITH SPECIFIED ELEVATED TEMPERATURE PROPERTIES |
EN ISO 2566-2:1999 | Steel - Conversion of elongation values - Part 2: Austenitic steels (ISO 2566-2:1984) |
ISO 17632:2015 | Welding consumables Tubular cored electrodes for gas shielded and non-gas shielded metal arc welding of non-alloy and fine grain steels Classification |
EN 10222-4:2017 | Steel forgings for pressure purposes - Part 4: Weldable fine grain steels with high proof strength |
EN ISO 14343:2017 | Welding consumables - Wire electrodes, strip electrodes, wires and rods for arc welding of stainless and heat resisting steels - Classification (ISO 14343:2017) |
EN 10222-2:2017 | Steel forgings for pressure purposes - Part 2: Ferritic and martensitic steels with specified elevated temperatures properties |
EN 760:1996 | Welding consumables - Fluxes for submerged arc welding - Classification |
ISO 8495:2013 | Metallic materials Tube Ring-expanding test |
EN 10204:2004 | Metallic products - Types of inspection documents |
CEN ISO/TR 15608:2017 | Welding - Guidelines for a metallic materials grouping system (ISO/TR 15608:2017) |
EN ISO 17632:2015 | Welding consumables - Tubular cored electrodes for gas shielded and non-gas shielded metal arc welding of non-alloy and fine grain steels - Classification (ISO 17632:2015) |
ISO 17634:2015 | Welding consumables Tubular cored electrodes for gas shielded metal arc welding of creep-resisting steels Classification |
EN ISO 6892-2:2011 | Metallic materials - Tensile testing - Part 2: Method of test at elevated temperature (ISO 6892-2:2011) |
EN 1600:1997 | Welding consumables - Covered electrodes for manual arc welding of stainless and heat resisting steels - Classification |
ISO 9001:2015 | Quality management systems — Requirements |
EN 10217-3:2002/A1:2005 | WELDED STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 3: ALLOY FINE GRAIN STEEL TUBES |
EN 12074:2000 | Welding consumables - Quality requirements for manufacture, supply and distribution of consumables for welding and allied processes |
ISO 6892-2:2011 | Metallic materials Tensile testing Part 2: Method of test at elevated temperature |
EN ISO 148-1:2016 | Metallic materials - Charpy pendulum impact test - Part 1: Test method (ISO 148-1:2016) |
EN ISO 636:2017 | Welding consumables - Rods, wires and deposits for tungsten inert gas welding of non-alloy and fine-grain steels - Classification (ISO 636:2017) |
EN ISO/IEC 17021:2011 | Conformity assessment - Requirements for bodies providing audit and certification of management systems (ISO/IEC 17021:2011) |
EN 10160:1999 | Ultrasonic testing of steel flat product of thickness equal or greater than 6 mm (reflection method) |
ISO 10893-10:2011 | Non-destructive testing of steel tubes Part 10: Automated full peripheral ultrasonic testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of longitudinal and/or transverse imperfections |
ISO 636:2017 | Welding consumables — Rods, wires and deposits for tungsten inert gas welding of non-alloy and fine-grain steels — Classification |
ISO 18275:2011 | Welding consumables Covered electrodes for manual metal arc welding of high-strength steels Classification |
EN 764-4:2014 | Pressure equipment - Part 4: Establishment of technical delivery conditions for metallic materials |
EN 12952-5:2011 | Water-tube boilers and auxiliary installations - Part 5: Workmanship and construction of pressure parts of the boiler |
EN 10253-2:2007 | Butt-welding pipe fittings - Part 2: Non alloy and ferritic alloy steels with specific inspection requirements |
EN 757:1997 | Welding consumables - Covered electrodes for manual metal arc welding of high strength steels - Classification |
EN 10217-5:2002/A1:2005 | WELDED STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 5: SUBMERGED ARC WELDED NON-ALLOY AND ALLOY STEEL TUBES WITH SPECIFIED ELEVATED TEMPERATURE PROPERTIES |
EN 13479:2017 | Welding consumables - General product standard for filler metals and fluxes for fusion welding of metallic materials |
EN ISO 14344:2010 | Welding consumables - Procurement of filler materials and fluxes (ISO 14344:2010) |
EN 10216-3:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 3: Alloy fine grain steel tubes |
EN 12952-6:2011 | Water-tube boilers and auxiliary installations - Part 6: Inspection during construction; documentation and marking of pressure parts of the boiler |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.