I.S. EN 13480-2:2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
10-03-2019
07-16-2017
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
European foreword
1 Scope
2 Normative references
3 Terms and definitions, symbols and units
4 Requirements for materials to be used for pressure containing parts in industrial piping
5 Requirements for materials to be used for non‐pressure parts
Annex A (normative) Grouping system for steels for pressure equipment
Annex B (normative) Requirements for prevention of brittle fracture at low temperatures
Annex C (normative) Provisional technical delivery conditions for clad products for pressure purposes
Annex D (informative) European steels for pressure purposes
Annex Y (informative) History of EN 13480‐2
Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2014/68/EU aimed to be covered
Bibliography
This Part of this European Standard specifies the requirements for materials (including metallic clad
materials) for industrial piping and supports covered by EN 13480‐1 manufactured from of metallic
materials.
| Committee |
CEN/TC 267
|
| DocumentType |
Standard
|
| Pages |
88
|
| ProductNote |
Consolidated Version is available This standard is Identical to EN 13480-2:2017/A3 CSV VERSION NOW AVAILABLE NOTE: The date of any NSAI previous adoption may not match the date of its original CEN/CENELEC document. THIS STANDARD ALSO REFERS TO EN 1092‐1:2007,EN 10028‐1:2007+A1:2009+AC:2009,EN 10028‐2:2009,EN 10028‐3:2009,EN 10028‐4:2009,EN 10028‐5:2009,EN 10028‐6:2009,EN 10028‐7:2007,EN 10213:2007,EN 10216‐1:2002+A1:2004,EN 10216‐2:2002+A2:2007,EN 10216]3:2002+A1:2004,EN 10216‐4:2002+A1:2004,EN 10216‐5:2004,EN 10217‐7:2005,EN 10222‐1:1998+A1:2002,EN 10222‐2:2000,EN 10222‐4:1998+A1:2001,EN 10222‐5:2000,EN 10269:1999+A1:2006,EN 10272:2007,EN 10273:2007,EN 12074:1999,EN 13479:2004,EN ISO 148‐1:2010,EN ISO 898‐1:2009,EN ISO 3506‐1:1997,EN ISO 3506‐2:1997,2014/68/EU:2014,prEN 13445‐2,EN 764‐4:2002,EN 764‐5:2002,EN 1011‐2:2001,EN 10079:1992,EN ISO 14343:2007,
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NS EN 13480-2 : 2017 | Identical |
| DIN EN 13480-2:2014-12 | Identical |
| BS EN 13480-2:2017 | Identical |
| NBN EN 13480-2 : 2012 AMD 2 2016 | Identical |
| NEN EN 13480-2 : 2017 | Identical |
| EN 13480-2:2017 | Identical |
| UNI EN 13480-2 : 2013 | Identical |
| EN 13480-2:2017/A2:2018 | Identical |
| ONORM EN 13480-2 : 2017 | Identical |
| NF EN 13480-2 : 2017 | Identical |
| UNE-EN 13480-2:2017 | Identical |
| EN 10002-1 : 2001 | METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE |
| EN 10269:2013 | Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties |
| EN 10079:2007 | Definition of steel products |
| ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs |
| BS 7910:1999 | Guide on methods for assessing the acceptability of flaws in metallic structures |
| EN 13480-4:2017 | Metallic industrial piping - Part 4: Fabrication and installation |
| EN 10273:2016 | Hot rolled weldable steel bars for pressure purposes with specified elevated temperature properties |
| EN 13445-5:2014 | Unfired pressure vessels - Part 5: Inspection and testing |
| EN ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:2009) |
| EN 10164:2004 | Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions |
| ISO/TR 15608:2017 | Welding Guidelines for a metallic materials grouping system |
| EN 10222-3:1998 | Steel forgings for pressure purposes - Part 3: Nickel steels with specified low temperature properties |
| ISO 2566-2:1984 | Steel Conversion of elongation values Part 2: Austenitic steels |
| EN 10217-4:2002/A1:2005 | WELDED STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 4: ELECTRIC WELDED NON-ALLOY STEEL TUBES WITH SPECIFIED LOW TEMPERATURE PROPERTIES |
| EN 13480-1:2017 | Metallic industrial piping - Part 1: General |
| EN ISO 2566-1:1999 | Steel - Conversion of elongation values - Part 1: Carbon and low alloy steels (ISO 2566-1:1984) |
| EN 764-5:2014 | Pressure equipment - Part 5: Inspection documentation of metallic materials and compliance with the material specification |
| EN 20898-2 : 1993 | MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992) |
| EN 13445-4:2014 | Unfired pressure vessels - Part 4: Fabrication |
| EN 1011-2:2001/A1:2003 | WELDING - RECOMMENDATIONS FOR WELDING OF METALLIC MATERIALS - PART 2: ARC WELDING OF FERRITIC STEELS |
| ISO 148-1:2016 | Metallic materials — Charpy pendulum impact test — Part 1: Test method |
| EN 13480-3:2017 | Metallic industrial piping - Part 3: Design and calculation |
| EN 10272:2016 | Stainless steel bars for pressure purposes |
| EN 10222-5:2017 | Steel forgings for pressure purposes - Part 5: Martensitic, austenitic and austenitic-ferritic stainless steels |
| ISO 2566-1:1984 | Steel Conversion of elongation values Part 1: Carbon and low alloy steels |
| EN 10217-2:2002/A1:2005 | WELDED STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 2: ELECTRIC WELDED NON-ALLOY AND ALLOY STEEL TUBES WITH SPECIFIED ELEVATED TEMPERATURE PROPERTIES |
| EN ISO 2566-2:1999 | Steel - Conversion of elongation values - Part 2: Austenitic steels (ISO 2566-2:1984) |
| EN 10222-4:2017 | Steel forgings for pressure purposes - Part 4: Weldable fine grain steels with high proof strength |
| EN ISO 14343:2017 | Welding consumables - Wire electrodes, strip electrodes, wires and rods for arc welding of stainless and heat resisting steels - Classification (ISO 14343:2017) |
| EN 10222-2:2017 | Steel forgings for pressure purposes - Part 2: Ferritic and martensitic steels with specified elevated temperatures properties |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| 2014/68/EU : 2014 COR 1 2015 | DIRECTIVE 2014/68/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 15 MAY 2014 ON THE HARMONISATION OF THE LAWS OF THE MEMBER STATES RELATING TO THE MAKING AVAILABLE ON THE MARKET OF PRESSURE EQUIPMENT TEXT WITH EEA RELEVANCE |
| CEN ISO/TR 15608:2017 | Welding - Guidelines for a metallic materials grouping system (ISO/TR 15608:2017) |
| EN ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013) |
| EN 10217-3:2002/A1:2005 | WELDED STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 3: ALLOY FINE GRAIN STEEL TUBES |
| EN 12074:2000 | Welding consumables - Quality requirements for manufacture, supply and distribution of consumables for welding and allied processes |
| AD MERKBLATT W8 : 2001 | MATERIALS - CLAD STEELS |
| EN ISO 148-1:2016 | Metallic materials - Charpy pendulum impact test - Part 1: Test method (ISO 148-1:2016) |
| EN 13480-5:2017 | Metallic industrial piping - Part 5: Inspection and testing |
| ISO 3506-2:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 2: Nuts |
| SEL 075 : 1983 | PLATED PRODUCTS |
| EN 764-3:2002 | Pressure equipment - Part 3: Definition of parties involved |
| EN 764-4:2014 | Pressure equipment - Part 4: Establishment of technical delivery conditions for metallic materials |
| EN 10253-2:2007 | Butt-welding pipe fittings - Part 2: Non alloy and ferritic alloy steels with specific inspection requirements |
| EN 10217-1:2002/A1:2005 | WELDED STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - NON-ALLOY STEEL TUBES WITH SPECIFIED ROOM TEMPERATURE PROPERTIES |
| EN 10217-5:2002/A1:2005 | WELDED STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 5: SUBMERGED ARC WELDED NON-ALLOY AND ALLOY STEEL TUBES WITH SPECIFIED ELEVATED TEMPERATURE PROPERTIES |
| EN 13479:2017 | Welding consumables - General product standard for filler metals and fluxes for fusion welding of metallic materials |
| EN 10217-6:2002/A1:2005 | WELDED STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 6: SUBMERGED ARC WELDED NON-ALLOY STEEL TUBES WITH SPECIFIED LOW TEMPERATURE PROPERTIES |
| ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
| EN 10222-1:2017 | Steel forgings for pressure purposes - Part 1: General requirements for open die forgings |
| EN ISO 3506-2:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 2: Nuts (ISO 3506-2:2009) |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.