I.S. EN 1494:2000
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
MOBILE OR MOVABLE JACKS AND ASSOCIATED LIFTING EQUIPMENT
Hardcopy , PDF
02-06-2009
English
04-12-2001
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of hazards
5 Safety requirements
5.1 Braking device
5.1.1 General
5.1.2 Dimensioning
5.1.3 Interruption of the power flow
5.1.4 Automatic operation
5.1.5 Alterations
5.2 Security against dropping
5.3 Speeds
5.4 Security against overloading
5.5 Transmission systems
5.5.1 Security of guides
5.5.2 End stops
5.5.3 Additional requirements for hydraulic jacks
5.5.4 Additional requirements for pneumatic jacks
5.6 Control devices
5.6.1 Hold to run control
5.6.2 Unintentional operation
5.6.3 Identification
5.6.4 Obviousness
5.6.5 Visibility
5.6.6 Control devices of manually operated jacks
5.6.7 External power supply
5.7 Combined manual and power-operated jacks
5.8 Requirements for safety mechanisms
5.8.1 Adjustments
5.8.2 Materials
5.8.3 Effects of weather and dirt
5.8.4 Breakage of springs
5.9 Lift pad
5.10 Structural design
5.11 Climatic conditions
5.12 Hot surfaces
5.13 Forces
5.14 Protection against pinching and shearing
5.15 Electricity
5.16 Transport and installation equipment
5.17 Provisions for maintenance
5.17.1 Accessibility
5.17.2 Adjustment
5.18 Special requirements for hydraulic transmission jacks
5.18.1 Holding device
5.18.2 Lowering speed
5.19 Special requirements for trolley jacks
5.19.1 Guidance of the lift pad
5.19.2 Lowering of the load
5.20 Special requirements for pit jacks
5.20.1 Overturning protection
5.20.2 Lowering speed
5.20.3 Adjustments
5.20.4 Hold to run control
5.20.5 Unintentional operation
5.20.6 Crash protection
5.21 Special requirements for jacks without integrated pump
6 Verification
6.1 General
6.1.1 Tests
6.1.2 Design check
6.1.3 Manufacturing check
6.1.4 Visual verification
6.1.5 Practical tests
6.1.6 Electrical tests
6.2 Individual final verification before despatch
7 Information for use
7.1 Instruction for use and instruction handbook
7.1.1 General
7.1.2 Rules for operating
7.1.3 Maintenance and repair
7.2 Minimum marking
Annex A (normative) Noise
Annex B (normative) Test procedures
Annex C (normative) Manual forces and manual force measurement
methods
Annex ZA (informative) Relationship between this European Standard
and the Essential Requirements of EU Directive 98/37/EC
Annex ZB (informative) Relationship between this European Standard
and the Essential Requirements of EU Directive 2006/42/EC
Important note : All end users must be registered with an Account prior to user licenses being assigned.Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.