|
ISO 272:1982
|
Fasteners — Hexagon products — Widths across flats
|
|
IEC 61076-1:2006
|
Connectors for electronic equipment - Product requirements - Part 1: Generic specification
|
|
IEC 60512-11-4:2002
|
Connectors for electronic equipment - Tests and measurements - Part 11-4: Climatic tests - Test 11d: Rapid change of temperature
|
|
IEC 60512-8:1993
|
Electromechanical components for electronic equipment; basic testing procedures and measuring methods - Part 8: Connector tests (mechanical) and mechanical tests on contacts and terminations
|
|
IEC 60512-11-9:2002
|
Connectors for electronic equipment - Tests and measurements - Part 11-9: Climatic tests - Test 11i: Dry heat
|
|
IEC 60512-11-10:2002
|
Connectors for electronic equipment - Tests and measurements - Part 11-10: Climatic tests - Test 11j: Cold
|
|
IEC 60512-4-2:2002
|
Connectors for electronic equipment - Tests and measurements - Part 4-2: Voltage stress tests - Test 4b: Partial discharge
|
|
IEC 60512-3-1:2002
|
Connectors for electronic equipment - Tests and measurements - Part 3-1: Insulation tests - Test 3a: Insulation resistance
|
|
IEC 60068-1:2013
|
Environmental testing - Part 1: General and guidance
|
|
IEC 60512-6:1984
|
Electromechanical components for electronic equipment; basic testing procedures and measuring methods. Part 6: Climatic tests and soldering tests
|
|
IEC 60512-6-3:2002
|
Connectors for electronic equipment - Tests and measurements - Part 6-3: Dynamic stress tests - Test 6c: Shock
|
|
IEC 60512-11-8:1995
|
Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 11: Climatic tests - Section 8: Test 11h - Sand and dust
|
|
IEC 60512-6-1:2002
|
Connectors for electronic equipment - Tests and measurements - Part 6-1: Dynamic stress tests - Test 6a: Acceleration, steady state
|
|
IEC 60512-7:1993
|
Electromechanical components for electronic equipment; basic testing procedures and measuring methods - Part 7: Mechanical operating tests and sealing tests
|
|
IEC 60512-11-14:2003
|
Connectors for electronic equipment - Tests and measurements - Part 11-14: Climatic tests - Test 11p: Flowing single gas corrosion test
|
|
IEC 60097:1991
|
Grid systems for printed circuits
|
|
IEC 60512-2-5:2003
|
Connectors for electronic equipment - Tests and measurements - Part 2-5: Electrical continuity and contact resistance tests - Test 2e: Contact disturbance
|
|
IEC 60352-1:1997
|
Solderless connections - Part 1: Wrapped connections - General requirements, test methods and practical guidance
|
|
IEC 60603-2:1995
|
Connectors for frequencies below 3 MHz for use with printed boards - Part 2: Detail specification for two-part connectors with assessed quality, for printed boards, for basic grid of 2,54 mm (0,1 in) with common mounting features
|
|
IEC 60410:1973
|
Sampling plans and procedures for inspection by attributes
|
|
IEC 60512-11-3:2002
|
Connectors for electronic equipment - Tests and measurements - Part 11-3: Climatic tests - Test 11c: Damp heat, steady state
|
|
ISO 468:1982
|
Surface roughness — Parameters, their values and general rules for specifying requirements
|
|
IEC 60512-1-1:2002
|
Connectors for electronic equipment - Tests and measurements - Part 1-1: General examination - Test 1a: Visual examination
|
|
IEC 60352-5:2012
|
Solderless connections - Part 5: Press-in connections - General requirements, test methods and practical guidance
|
|
IEC 61076-4:1995
|
Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high-speed data applications - Part 4: Sectional specification - Printed board connectors
|
|
IEC 60512-11-1:1995
|
Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 11: Climatic tests - Section 1: Test 11a - Climatic sequence
|
|
IEC 60512-2-1:2002
|
Connectors for electronic equipment - Tests and measurements - Part 2-1: Electrical continuity and contact resistance tests - Test 2a: Contact resistance - Millivolt level method
|
|
IEC 60194:2015
|
Printed board design, manufacture and assembly - Terms and definitions
|
|
IEC 60512-11-12:2002
|
Connectors for electronic equipment - Tests and measurements - Part 11-12: Climatic tests - Test 11m: Damp heat, cyclic
|
|
IEC 60512-4-1:2003
|
Connectors for electronic equipment - Tests and measurements - Part 4-1: Voltage stress tests - Test 4a: Voltage proof
|
|
IEC 60512-9:1992
|
Electromechanical components for electronic equipment; basic testing procedures and measuring methods - Part 9: Miscellaneous tests
|
|
IEC 60512-11-5:2002
|
Connectors for electronic equipment - Tests and measurements - Part 11-5: Climatic tests - Test 11e: Mould growth
|
|
IEC 60512-5:1992
|
Electromechanical components for electronic equipment; basic testing procedures and measuring methods - Part 5: Impact tests (free components), static load tests (fixed components), endurance tests and overload tests
|
|
IEC 60512-1:2001
|
Connectors for electronic equipment - Tests and measurements - Part 1: General
|
|
IEC 60512-6-4:2002
|
Connectors for electronic equipment - Tests and measurements - Part 6-4: Dynamic stress tests - Test 6d: Vibration (sinusoidal)
|
|
IEC 60326-3:1991
|
Printed boards - Part 3: Design and use of printed boards
|
|
IEC 60512-1-2:2002
|
Connectors for electronic equipment - Tests and measurements - Part 1-2: General examination - Test 1b: Examination of dimension and mass
|
|
IEC 60512-11-11:2002
|
Connectors for electronic equipment - Tests and measurements - Part 11-11: Climatic tests - Test 11k: Low air pressure
|
Important note : All end users must be registered with an Account prior to user licenses being assigned.