• There are no items in your cart

I.S. EN ISO 10350-1:2017

Current
Current

The latest, up-to-date edition.

PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 1: MOULDING MATERIALS (ISO 10350-1:2017)
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-01-2017

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

National Foreword
European foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Specimen preparation and conditioning
5 Test requirements
6 Presentation of results
Bibliography

Describes specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics.

DevelopmentNote
Supersedes I.S. EN ISO 10350. (10/2006)
DocumentType
Standard
Pages
28
PublisherName
National Standards Authority of Ireland
Status
Current
Supersedes

IEC 60243-1:2013 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
IEC 60695-11-20:2015 Fire hazard testing - Part 11-20: Test flames - 500 W flame test method
IEC 60112:2003+AMD1:2009 CSV Method for the determination of the proof and the comparative tracking indices of solid insulating materials
ISO 75-1:2013 Plastics Determination of temperature of deflection under load Part 1: General test method
ISO 10350-2:2011 Plastics Acquisition and presentation of comparable single-point data Part 2: Long-fibre-reinforced plastics
ISO 6603-2:2000 Plastics — Determination of puncture impact behaviour of rigid plastics — Part 2: Instrumented impact testing
ISO 3915:1981 Plastics — Measurement of resistivity of conductive plastics
ISO 293:2004 Plastics — Compression moulding of test specimens of thermoplastic materials
ISO 3167:2014 Plastics Multipurpose test specimens
IEC 60250:1969 Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths
ISO 11403-3:2014 Plastics Acquisition and presentation of comparable multipoint data Part 3: Environmental influences on properties
ISO 294-3:2002 Plastics Injection moulding of test specimens of thermoplastic materials Part 3: Small plates
ISO 1133-1:2011 Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method
ISO 295:2004 Plastics — Compression moulding of test specimens of thermosetting materials
IEC 62631-3-2:2015 Dielectric and resistive properties of solid insulating materials - Part 3-2: Determination of resistive properties (DC methods) - Surface resistance and surface resistivity
ISO 10724-1:1998 Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens
ISO 8256:2004 Plastics — Determination of tensile-impact strength
ISO 11359-2:1999 Plastics Thermomechanical analysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature
IEC 62631-3-1:2016 Dielectric and resistive properties of solid insulating materials - Part 3-1: Determination of resistive properties (DC methods) - Volume resistance and volume resistivity - General method
ISO 75-2:2013 Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
ISO 11357-3:2011 Plastics Differential scanning calorimetry (DSC) Part 3: Determination of temperature and enthalpy of melting and crystallization
ISO 11357-2:2013 Plastics Differential scanning calorimetry (DSC) Part 2: Determination of glass transition temperature and glass transition step height
ISO 11403-2:2012 Plastics — Acquisition and presentation of comparable multipoint data — Part 2: Thermal and processing properties
IEC 60296:2012 RLV Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear
ISO 294-4:2001 Plastics Injection moulding of test specimens of thermoplastic materials Part 4: Determination of moulding shrinkage
ISO 2577:2007 Plastics Thermosetting moulding materials Determination of shrinkage
IEC 60695-11-10:2013 Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
ISO 1183-1:2012 Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
ISO 1183-2:2004 Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method
ISO 1183-3:1999 Plastics Methods for determining the density of non-cellular plastics Part 3: Gas pyknometer method
ISO 291:2008 Plastics Standard atmospheres for conditioning and testing
ISO 179-1:2010 Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 62:2008 Plastics Determination of water absorption
ISO 306:2013 Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
ISO 294-1:2017 Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
ISO 4589-2:2017 Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test
ISO 2818:1994 Plastics — Preparation of test specimens by machining
ISO 1133-2:2011 Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 2: Method for materials sensitive to time-temperature history and/or moisture
ISO 899-1:2017 Plastics — Determination of creep behaviour — Part 1: Tensile creep
ISO 11403-1:2014 Plastics Acquisition and presentation of comparable multipoint data Part 1: Mechanical properties
ISO 20753:2008 Plastics Test specimens
ISO 178:2010 Plastics Determination of flexural properties
ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
ISO 10724-2:1998 Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 2: Small plates

View more information
US$30.69
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.