• There are no items in your cart

I.S. EN ISO 15156-3:2015&LC:2015

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

PETROLEUM AND NATURAL GAS INDUSTRIES - MATERIALS FOR USE IN H[2]S-CONTAINING ENVIRONMENTS IN OIL AND GAS PRODUCTION - PART 3: CRACKING-RESISTANT CRAS (CORROSION-RESISTANT ALLOYS) AND OTHER ALLOYS (ISO 15156-3:2015)
Available format(s)

Hardcopy , PDF

Superseded date

01-04-2021

Language(s)

English

Published date

01-01-2015

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

National Foreword
European foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Factors affecting the cracking-resistance of CRAs
  and other alloys in H[2]S containing environments
6 Qualification and selection of CRAs and other
  alloys with respect to SSC, SCC, and GHSC in
  H[2]S-containing environments
7 Purchasing information and marking
Annex A (normative) - Environmental cracking-resistant
        CRAs and other alloys (including Table A.1 - Guidance
        on the use of the materials selection tables)
Annex B (normative) - Qualification of CRAs for
        H[2]S-service by laboratory testing
Annex C (informative) - Information that should be
        supplied for material purchasing
Annex D (informative) - Materials chemical compositions
        and other information
Annex E (informative) - Nominated sets of test conditions
Bibliography

Provides requirements and recommendations for the selection and qualification of CRAs (corrosion-resistant alloys) and other alloys for service in equipment used in oil and natural gas production and natural gas treatment plants in H[2]S-containing environments whose failure can pose a risk to the health and safety of the public and personnel or to the environment.

Committee
TC 67
DocumentType
Standard
Pages
102
ProductNote
The date of any NSAI previous adoption may not match the date of its original CEN/CENELEC document. CORRECTED VERSION IS NOW AVAILABLE OF THIS STANDARD FROM 05-08-2019.
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy
Supersedes

ISO 6507-1:2005 Metallic materials Vickers hardness test Part 1: Test method
ISO 13680:2010 Petroleum and natural gas industries Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling stock Technical delivery conditions
ISO 15510:2014 Stainless steels Chemical composition
ASTM E 562 : 2011 : REDLINE Standard Test Method for Determining Volume Fraction by Systematic Manual Point Count
NACE TM 02 84 : 2016 EVALUATION OF PIPELINE AND PRESSURE VESSEL STEELS FOR RESISTANCE TO HYDROGEN-INDUCED CRACKING
ISO 6508-1:2016 Metallic materials — Rockwell hardness test — Part 1: Test method
ASTM A 744/A744M : 2013 : REDLINE Standard Specification for Castings, Iron-Chromium-Nickel, Corrosion Resistant, for Severe Service
ASTM E 384 : 2017 : REDLINE Standard Test Method for Microindentation Hardness of Materials
ISO 6892-1:2016 Metallic materials Tensile testing Part 1: Method of test at room temperature
NACE TM 01 77 : 2016 LABORATORY TESTING OF METALS FOR RESISTANCE TO SULFIDE STRESS CRACKING AND STRESS CORROSION CRACKING IN H[2]S ENVIRONMENTS
SAE AMS 2430 : 2015 SHOT PEENING
NACE TM 01 98 : 2016 SLOW STRAIN RATE TEST METHOD FOR SCREENING CORROSION-RESISTANT ALLOYS FOR STRESS CORROSION CRACKING IN SOUR OILFIELD SERVICE
ISO 15156-2:2015 Petroleum and natural gas industries Materials for use in H2S-containing environments in oil and gas production Part 2: Cracking-resistant carbon and low-alloy steels, and the use of cast irons
ISO 7539-7:2005 Corrosion of metals and alloys Stress corrosion testing Part 7: Method for slow strain rate testing
ISO 15156-1:2015 Petroleum and natural gas industries Materials for use in H2S-containing environments in oil and gas production Part 1: General principles for selection of cracking-resistant materials
ISO 10423:2009 Petroleum and natural gas industries Drilling and production equipment Wellhead and christmas tree equipment
NACE MR 01 76 : 2012 METALLIC MATERIALS FOR SUCKER-ROD PUMPS FOR CORROSIVE OILFIELD ENVIRONMENTS
ISO 11960:2014 Petroleum and natural gas industries Steel pipes for use as casing or tubing for wells

View more information
US$152.38
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.