• I.S. EN ISO 16812:2007

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - SHELL-AND-TUBE HEAT EXCHANGERS

    Available format(s):  Hardcopy, PDF

    Superseded date:  04-04-2019

    Language(s):  English

    Published date:  01-01-2007

    Publisher:  National Standards Authority of Ireland

    Add to Watchlist

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 General
    5 Proposals
    6 Drawings and other required data
       6.1 Outline drawings and other supporting data
       6.2 Information required after drawings are reviewed
       6.3 Reports and records
    7 Design
       7.1 Design temperature
       7.2 Cladding for corrosion allowance
       7.3 Shell supports
       7.4 Stationary head
       7.5 Floating head
       7.6 Tube bundle
       7.7 Nozzles and other connections
       7.8 Flanged external girth joints
       7.9 Expansion joints
       7.10 Gaskets
       7.11 Handling devices
       7.12 Hydrogen service
    8 Materials
       8.1 General
       8.2 Gaskets
       8.3 Tubes
    9 Fabrication
       9.1 Shells
       9.2 Pass-partition plates
       9.3 Connection junctions
       9.4 Tubes
       9.5 Welding
       9.6 Heat treatment
       9.7 Dimensional tolerances
       9.8 Gasket contact surfaces other than nozzle flange
            facings
       9.9 Tube holes
       9.10 Tube-to-tubesheet joints
       9.11 Assembly
    10 Inspection and testing
       10.1 Quality assurance
       10.2 Quality control
       10.3 Pressure testing
       10.4 Nameplates and stampings
    11 Preparation for shipment
       11.1 Protection
       11.2 Identification
    12 Supplemental requirements
       12.1 General
       12.2 Design
       12.3 Examination
    Annex A (informative) Recommended practices
    Annex B (informative) Shell-and-tube heat exchanger checklist
    Annex C (informative) Shell-and-tube heat exchanger data sheets
    Annex D (informative) Responsibility data sheet
    Bibliography

    Abstract - (Show below) - (Hide below)

    Defines requirements and gives recommendations for the mechanical design, material selection, fabrication, inspection, testing and preparation for shipment of shell-and-tube heat exchangers for the petroleum, petrochemical and natural gas industries.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ASME PV CODE 2C : 2017 BOILER AND PRESSURE VESSEL CODE - MATERIALS - SPECIFICATIONS FOR WELDING RODS, ELECTRODES, AND FILLER METALS
    ASME PV CODE 2A : 2017 BOILER AND PRESSURE VESSEL CODE - MATERIALS - FERROUS MATERIAL SPECIFICATIONS (BEGINNING TO SA-450) AND (SA-451 TO END)
    ASME PV CODE 2B : 2017 BOILER AND PRESSURE VESSEL CODE - MATERIALS - NONFERROUS MATERIAL SPECIFICATIONS
    NACE MR 01 75 : 2003 METALS FOR SULFIDE STRESS CRACKING AND STRESS CORROSION CRACKING RESISTANCE IN SOUR OILFIELD ENVIRONMENTS
    API 521 : 2014 PRESSURE-RELIEVING AND DEPRESSURING SYSTEMS
    ANSI/NACE MR 01 03/ISO 17495-1:2016 PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - METALLIC MATERIALS RESISTANT TO SULFIDE STRESS CRACKING IN CORROSIVE PETROLEUM REFINING ENVIRONMENTS
    ASME PV CODE 8 DIV 1 : 2017 BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 1
    ASME PV CODE 2D CUSTOMARY : 2017 BOILER AND PRESSURE VESSEL CODE - MATERIALS - PROPERTIES (CUSTOMARY)
    ASME PV CODE 2D METRIC : 2017 BOILER AND PRESSURE VESSEL CODE - MATERIALS - PROPERTIES (METRIC)
    ASME B16.5 : 2017 PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD
    TEMA STANDARDS : 9ED 2007 STANDARDS OF THE TUBULAR EXCHANGER MANUFACTURERS ASSOCIATION
    ASME B16.11 : 2016 FORGED FITTINGS, SOCKET-WELDING AND THREADED
    ISO 23251:2006 Petroleum, petrochemical and natural gas industries Pressure-relieving and depressuring systems
    ASME B1.20.1 : 2013(R2018) PIPE THREADS, GENERAL PURPOSE (INCH)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective