• There are no items in your cart

IEC 62282-2:2012

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Fuel cell technologies - Part 2: Fuel cell modules
Available format(s)

Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users

Superseded date

12-31-2021

Language(s)

English - French, Spanish, Castilian

Published date

03-26-2012

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Type tests
6 Routine tests
7 Markings and instructions
Annex A (informative) - Additional information for the
        performance and evaluation of the tests
Annex B (informative) - List of notes concerning
        particular conditions in certain countries
Bibliography

IEC 62282-2:2012 provides the minimum requirements for safety and performance of fuel cell modules; it applies to fuel cell modules with or without an enclosure which can be operated at significant pressurization levels or close to ambient pressure. Deals with conditions that can yield hazards to persons and cause damage outside the fuel cell modules. This edition includes the following significant technical changes with respect to the previous edition:
- inclusion of definitions for hazards and hazardous locations based on the IEC 60079 series;
- modification of the general safety strategy and of the electrical components clause to reflect the needs for different application standards. Key word: fuel cell

Committee
TC 105
DevelopmentNote
Stability Date: 2015. (10/2012)
DocumentType
Standard
Pages
82
PublisherName
International Electrotechnical Committee
Status
Superseded
Supersedes

PD IEC/TS 62282-7-2:2014 Fuel cell technologies Test methods. Single cell and stack performance tests for solid oxide fuel cells (SOFC)
BS EN 62282-3-1:2007 Fuel cell technologies Stationary fuel cell power systems. Safety
05/30060689 DC : DRAFT JUN 2005 IEC 62282-3-1 - FUEL CELL TECHNOLOGIES - PART 3-1: STATIONARY FUEL CELL POWER PLANTS - SAFETY
EN 62282-3-1 : 2007 FUEL CELL TECHNOLOGIES - PART 3-1: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY
BS EN 62282-5-1:2012 Fuel cell technologies Portable fuel cell power systems. Safety
PREN 50465 : DRAFT 2011 GAS APPLIANCES - COMBINED HEAT AND POWER APPLIANCE OF NOMINAL HEAT INPUT INFERIOR OR EQUAL TO 70 KW
I.S. EN 62282-3-1:2007 FUEL CELL TECHNOLOGIES - PART 3-1: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY
IEC 62282-5-1:2012 Fuel cell technologies - Part 5-1: Portable fuel cell power systems - Safety
UNE-EN 62282-3-1:2011 Fuel cell technologies - Part 3-1: Stationary fuel cell power systems - Safety
SAE AIR 6464 : 2013 EUROCAE/SAE WG80/AE-7AFC HYDROGEN FUEL CELLS AIRCRAFT FUEL CELL SAFETY GUIDELINES
13/30276640 DC : 0 BS EN 62282-4-101 ED 1.0 - FUEL CELL TECHNOLOGIES - PART 4-101: FUEL CELL POWER SYSTEMS FOR PROPULSION FOR OTHER THAN ROAD VEHICLES AND AUXILIARY POWER UNITS - FUEL CELL POWER SYSTEMS FOR ELECTRICALLY POWERED INDUSTRIAL TRUCKS - SAFETY
BS EN 62282-4-101:2014 Fuel cell technologies Fuel cell power systems for propulsion other than road vehicles and auxiliary power units (APU). Safety of electrically powered industrial trucks
IEC 62282-4-101:2014 Fuel cell technologies - Part 4-101: Fuel cell power systems for propulsion other than road vehicles and auxiliary power units (APU) - Safety of electrically powered industrial trucks
UNE-EN 62282-5-1:2013 Fuel cell technologies - Part 5-1: Portable fuel cell power systems - Safety
10/30173705 DC : DRAFT SEP 2010 BS EN 62282-5-1 - FUEL CELL TECHNOLOGIES - PART 5-1: PORTABLE FUEL CELL POWER SYSTEMS - SAFETY
11/30249911 DC : 0 BS EN 50465 - GAS APPLIANCES - COMBINED HEAT AND POWER APPLIANCE OF NOMINAL HEAT INPUT INFERIOR OR EQUAL TO 70 KW
07/30091745 DC : 0 BS IEC 62368 - AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - SAFETY - REQUIREMENTS
16/30354067 DC : 0 BS EN 62282-5-100 - FUEL CELL TECHNOLOGIES - PART 5-100: PORTABLE FUEL CELL POWER SYSTEMS - SAFETY
IEC 62282-3-1:2007 Fuel cell technologies - Part 3-1: Stationary fuel cell power systems - Safety
EN 62282-5-1:2012 FUEL CELL TECHNOLOGIES - PART 5-1: PORTABLE FUEL CELL POWER SYSTEMS - SAFETY (IEC 62282-5-1:2012)
EN 62282-4-101:2014 Fuel cell technologies - Part 4-101: Fuel cell power systems for propulsion other than road vehicles and auxiliary power units (APU) - Safety of electrically powered industrial trucks

IEC 61025:2006 Fault tree analysis (FTA)
IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV Information technology equipment - Safety - Part 1: General requirements
CSA B51 : 2014 BOILER, PRESSURE VESSEL, AND PRESSURE PIPING CODE
IEC 60812:2006 Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA)
IEC 60050-151:2001 International Electrotechnical Vocabulary (IEV) - Part 151: Electrical and magnetic devices
IEC TS 62282-1:2013 Fuel cell technologies - Part 1: Terminology
CSA C22.2 No. 60079.0 : 2015 EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS
ISO 4672:1997 Rubber and plastics hoses Sub-ambient temperature flexibility tests
IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
ISO 188:2011 Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
IEC 60079-20-1:2010 Explosive atmospheres - Part 20-1: Material characteristics for gas and vapour classification - Test methods and data
IEC 62040-1:2017 EXV UNINTERRUPTIBLE POWER SYSTEMS (UPS) - PART 1: SAFETY REQUIREMENTS
CGA 12.6 : M94(R1999) VEHICLE REFUELLING APPLIANCES
EN 50178:1997 Electronic equipment for use in power installations
CSA C22.2 No. 60529 : 2016 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE)
SAE J 1739 : 2009 POTENTIAL FAILURE MODE AND EFFECTS ANALYSIS IN DESIGN (DESIGN FMEA), POTENTIAL FAILURE MODE AND EFFECTS ANALYSIS IN MANUFACTURING AND ASSEMBLY PROCESSES (PROCESS FMEA)
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
IEC 62282-3-100:2012 Fuel cell technologies - Part 3-100: Stationary fuel cell power systems - Safety
ISO 37:2017 Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
ISO 1402:2009 Rubber and plastics hoses and hose assemblies Hydrostatic testing
ISO 1307:2006 Rubber and plastics hoses — Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses
IEC 62061:2005+AMD1:2012+AMD2:2015 CSV Safety of machinery - Functional safety of safety-related electrical, electronic and programmable electronic control systems
ISO 1436:2017 Rubber hoses and hose assemblies Wire-braid-reinforced hydraulic types for oil-based or water-based fluids Specification
ISO 13849-1:2015 Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design
ISO 23550:2011 Safety and control devices for gas burners and gas-burning appliances General requirements
IEC 60730-1:2013+AMD1:2015 CSV Automatic electrical controls - Part 1: General requirements

View more information
US$313.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.