• There are no items in your cart

IEC TS 60034-18-42:2008

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Rotating electrical machines - Part 18-42: Qualification and acceptance tests for partial discharge resistant electrical insulation systems (Type II) used in rotating electrical machines fed from voltage converters
Available format(s)

Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users

Superseded date

02-07-2017

Language(s)

English - French

Published date

08-28-2008

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Voltage effects from converter operation
   4.1 Voltages at the terminals of the converter-fed machine
   4.2 Electrical stresses in the insulation system of machine
        windings
        4.2.1 General
        4.2.2 Voltages stressing the phase/phase insulation
        4.2.3 Voltages stressing the phase/ground insulation
        4.2.4 Voltages stressing the turn insulation
5 Type II insulation systems
6 Stress factors for converter-fed Type II insulation systems
7 Qualification and acceptance tests
   7.1 General
   7.2 Qualification tests
   7.3 Acceptance test
8 Qualification of turn insulation
   8.1 General
   8.2 Test methods
9 Qualification of ground wall insulation systems
   9.1 General
   9.2 Test methods
   9.3 Use of 50 Hz or 60 Hz life data to predict the service
        life with a converter drive
10 Qualification of the stress control and corona protection
   system
   10.1 General
   10.2 Test methods
11 Preparation of test objects
   11.1 General
   11.2 Turn/turn samples
   11.3 Coils
12 Qualification test procedures
   12.1 General
   12.2 Turn/turn samples
   12.3 Coils
   12.4 Stress control samples
13 Qualification test pass criteria
   13.1 Turn/turn samples
   13.2 Coil samples
   13.3 Stress control samples
14 Acceptance test for Type II insulation systems (Type test)
   14.1 General
   14.2 Acceptance test methods
   14.3 Acceptance test pass criteria
15 Analysis, reporting and classification
Annex A (informative)
Annex B (informative)
Annex C (informative)

IEC/TS 60034-18-42:2008 defines criteria for assessing the insulation system of stator/rotor windings of single or polyphase AC machines which are subjected to repetitive impulse voltages, such as pulse width modulation converters, and expected to withstand partial discharge activity during service. It specifies electrical qualification and acceptance tests on representative samples which verify fitness for operation with voltage-source converters.

DevelopmentNote
Stability date: 2015. (10/2012)
DocumentType
Technical Specification
Pages
64
PublisherName
International Electrotechnical Committee
Status
Superseded
SupersededBy

BS EN 60034-15:2009 Rotating electrical machines Impulse voltage withstand levels of form-wound stator coils for rotating a.c. machines
I.S. EN 62068:2013 ELECTRICAL INSULATING MATERIALS AND SYSTEMS - GENERAL METHOD OF EVALUATION OF ELECTRICAL ENDURANCE UNDER REPETITIVE VOLTAGE IMPULSES (IEC 62068:2013 (EQV))
BS EN 60034-18-1:2010 Rotating electrical machines Functional evaluation of insulation systems. General guidelines
I.S. EN 60034-18-31:2012 ROTATING ELECTRICAL MACHINES - PART 18-31: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION OF INSULATION SYSTEMS USED IN ROTATING MACHINES (IEC 60034-18-31:2012 (EQV))
IEC TS 60034-18-33:2010 Rotating electrical machines - Part 18-33: Functional evaluation of insulation systems - Test procedures for form-wound windings - Multifactor evaluation by endurance under simultaneous thermal and electrical stresses
EN 60034-18-41:2014 Rotating electrical machines - Part 18-41: Partial discharge free electrical insulation systems (Type I) used in rotating electrical machines fed from voltage converters - Qualification and quality control tests
EN 60034-15:2009 Rotating electrical machines - Part 15: Impulse voltage withstand levels of form-wound stator coils for rotating a.c. machines
EN 60034-18-32:2010 Rotating electrical machines - Part 18-32: Functional evaluation of insulation systems - Test procedures for form-wound windings - Evaluation by electrical endurance
EN 60034-18-31 : 2012 ROTATING ELECTRICAL MACHINES - PART 18-31: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION OF INSULATION SYSTEMS USED IN ROTATING MACHINES (IEC 60034-18-31:2012)
EN 60034-18-1:2010 Rotating electrical machines - Part 18-1: Functional evaluation of insulation systems - General guidelines
I.S. EN 60034-18-41:2014 ROTATING ELECTRICAL MACHINES - PART 18-41: PARTIAL DISCHARGE FREE ELECTRICAL INSULATION SYSTEMS (TYPE 1) USED IN ROTATING ELECTRICAL MACHINES FED FROM VOLTAGE CONVERTERS - QUALIFICATION AND QUALITY CONTROL TESTS
DD CLC/TS 60034-18-33:2011 Rotating electrical machines Functional evaluation of insulation systems. Test procedures for form-wound windings. Multifactor evaluation by endurance under simultaneous thermal and electrical stresses
CLC/TS 60034-18-33:2011 Rotating electrical machines - Part 18-33: Functional evaluation of insulation systems - Test procedures for form-wound windings - Multifactor evaluation by endurance under simultaneous thermal and electrical stresses
CEI EN 60034-18-1 : 2011 ROTATING ELECTRICAL MACHINES - PART 18-1: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - GENERAL GUIDELINES
I.S. EN 60034-15:2009 ROTATING ELECTRICAL MACHINES - PART 15: IMPULSE VOLTAGE WITHSTAND LEVELS OF FORM-WOUND STATOR COILS FOR ROTATING A.C. MACHINES
I.S. EN 60034-18-32:2010 ROTATING ELECTRICAL MACHINES - PART 18-32: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - EVALUATION BY ELECTRICAL ENDURANCE
IEC TS 60034-25:2014 Rotating electrical machines - Part 25: AC electrical machines used in power drive systems - Application guide
CEI EN 62068 : 2014 ELECTRICAL INSULATING MATERIALS AND SYSTEMS - GENERAL METHOD OF EVALUATION OF ELECTRICAL ENDURANCE UNDER REPETITIVE VOLTAGE IMPULSES
BS EN 62068:2013 Electrical insulating materials and systems. General method of evaluation of electrical endurance under repetitive voltage impulses
BS EN 60034-18-31:2012 Rotating electrical machines Functional evaluation of insulation systems. Test procedures for form-wound windings. Thermal evaluation and classification of insulation systems used in rotating machines
CEI EN 60034-18-31 : 2013 ROTATING ELECTRICAL MACHINES - PART 18-31: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION OF INSULATION SYSTEMS USED IN ROTATING MACHINES
IEC 60034-18-32:2010 Rotating electrical machines - Part 18-32: Functional evaluation of insulation systems - Test procedures for form-wound windings - Evaluation by electrical endurance
CEI EN 60034-18-41 : 2014 ROTATING ELECTRICAL MACHINES - PART 18-41: PARTIAL DISCHARGE FREE ELECTRICAL INSULATION SYSTEMS (TYPE I) USED IN ROTATING ELECTRICAL MACHINES FED FROM VOLTAGE CONVERTERS - QUALIFICATION AND QUALITY CONTROL TESTS
BS EN 60034-18-32:2010 Rotating electrical machines Functional evaluation of insulation systems. Test procedures for form-wound windings. Evaluation by electrical endurance
S.R. CLC/TS 60034-18-33:2011 ROTATING ELECTRICAL MACHINES - PART 18-33: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - MULTIFACTOR EVALUATION BY ENDURANCE UNDER SIMULTANEOUS THERMAL AND ELECTRICAL STRESSES
UNE-EN 60034-18-31:2013 Rotating electrical machines - Part 18-31: Functional evaluation of insulation systems - Test procedures for form-wound windings - Thermal evaluation and classification of insulation systems used in rotating machines
I.S. EN 60034-18-1:2010 ROTATING ELECTRICAL MACHINES - PART 18-1: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - GENERAL GUIDELINES
IEC TS 61800-8:2010 Adjustable speed electrical power drive systems - Part 8: Specification of voltage on the power interface
IEC 62068:2013 Electrical insulating materials and systems - General method of evaluation of electrical endurance under repetitive voltage impulses
DD IEC/TS 61800-8:2010 Adjustable speed electrical power drive systems Specification of voltage on the power interface
IEC 60034-18-41:2014 Rotating electrical machines - Part 18-41: Partial discharge free electrical insulation systems (Type I) used in rotating electrical machines fed from voltage converters - Qualification and quality control tests
IEC 60034-18-31:2012 Rotating electrical machines - Part 18-31: Functional evaluation of insulation systems - Test procedures for form-wound windings - Thermal evaluation and classification of insulation systems used in rotating machines
11/30258048 DC : 0 BS EN 62068 - ELECTRICAL INSULATING MATERIALS AND SYSTEMS - GENERAL METHOD OF EVALUATION OF ELECTRICAL ENDURANCE UNDER REPETITIVE VOLTAGE IMPULSES
BS EN 60034-18-41:2014 Rotating electrical machines Partial discharge free electrical insulation systems (Type I) used in rotating electrical machines fed from voltage converters. Qualification and quality control tests
CEI EN 60034-15 : 2009 ROTATING ELECTRICAL MACHINES - PART 15: IMPULSE VOLTAGE WITHSTAND LEVELS OF FORM-WOUND STATOR COILS FOR ROTATING A.C. MACHINES
NF EN 60034 18-1 : 2010 ROTATING ELECTRICAL MACHINES - PART 18-1: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - GENERAL GUIDELINES
09/30194359 DC : 0 BS EN 60034-18-34 - ROTATING ELECTRICAL MACHINES - PART 18-34: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - EVALUATION OF THERMOMECHANICAL ENDURANCE OF INSULATION SYSTEMS
IEC 60034-18-1:2010 Rotating electrical machines - Part 18-1: Functional evaluation of insulation systems - General guidelines
EN 62068:2013 Electrical insulating materials and systems - General method of evaluation of electrical endurance under repetitive voltage impulses

IEC 61800-4:2002 Adjustable speed electrical power drive systems - Part 4: General requirements - Rating specifications for a.c. power drive systems above 1 000 V a.c. and not exceeding 35 kV
IEC TS 61251:2008 Electrical insulating materials - A.C. voltage endurance evaluation - Introduction
IEC 60034-18-32:2010 Rotating electrical machines - Part 18-32: Functional evaluation of insulation systems - Test procedures for form-wound windings - Evaluation by electrical endurance
IEC 62068-1:2003 Electrical insulation systems - Electrical stresses produced by repetitive impulses - Part 1: General method of evaluation of electrical endurance
IEC TS 60034-18-41:2006 Rotating electrical machines - Part 18-41: Qualification and type tests for Type I electrical insulation systems used in rotating electrical machines fed from voltage converters
IEC 60034-18-1:2010 Rotating electrical machines - Part 18-1: Functional evaluation of insulation systems - General guidelines
IEC 62539:2007 Guide for the statistical analysis of electrical insulation breakdown data
IEC 60216-3:2006 Electrical insulating materials - Thermal endurance properties - Part 3: Instructions for calculating thermal endurance characteristics

View more information
US$273.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.