Glass in building — Glass products for structural sealant glazing — Part 1: Supported and unsupported monolithic and multiple glazing

Available format(s)

Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users

Language(s)

English

Published date

11-21-2011

Publisher

International Organization for Standardization

ISO 28278-1:2011 specifies requirements for the suitability of supported and unsupported glass products for use in the structural sealant glazing (SSG) technique. Regarding glass products, ISO 28278-1:2011 constitutes a supplement to the requirements specified in the corresponding international standards with regard to verifying suitability for use in SSG systems.

Only soda lime silicate glass is taken into consideration in ISO 28278-1:2011.

The glass products are installed and bonded into the support under controlled environmental conditions as described in ISO 28278-2.

Plastic glazing is excluded from the scope of ISO 28278-1:2011.

The structural weatherproofing and sealant and outer seal of IGU products, which are commonly used in structural glazing applications are those based on organo-siloxane,"silicone" polymers, and recommended for use by the sealant manufacturer. Where there is a risk of earthquakes, the sealant design may not be sufficient to resist the loads, and complementary arrangements may be necessary.

ISO 28278-1:2011 does not preclude the use of other sealant types where these can demonstrate suitability for service according to ISO 28278-1:2011 and when used following the recommendations of the sealant manufacturer.

DevelopmentNote	Supersedes ISO/DIS 28278-1. (11/2011)
DocumentType	Standard
Pages	63
ProductNote	THIS STANDARD ALSO REFERS TO JIS R 3209,
PublisherName	International Organization for Standardization
Status	Current

EN 13022-1:2014	Glass in building - Structural sealant glazing - Part 1: Glass products for structural sealant glazing systems for supported and unsupported monolithic and multiple glazing
EN 572-3:2012	Glass in building - Basic soda lime silicate glass products - Part 3: Polished wired glass
ASTM C 1401 : 2014 : REDLINE	Standard Guide for Structural Sealant Glazing
ISO 7389:2002	Building construction Jointing products Determination of elastic recovery of sealants
ASTM C 1265 : 2017 : REDLINE	Standard Test Method for Determining the Tensile Properties of an Insulating Glass Edge Seal for Structural Glazing Applications
ASTM D 1149 : 2016-02	TEST METHODS FOR RUBBER DETERIORATION - CRACKING IN AN OZONE CONTROLLED ENVIRONMENT
EN 15434:2006+A1:2010	Glass in building - Product standard for structural and/or ultra-violet resistant sealant (for use with structural sealant glazing and/or insulating glass units with exposed seals)
EN 1991-1-3:2003/A1:2015	EUROCODE 1 - ACTIONS ON STRUCTURES - PART 1-3: GENERAL ACTIONS - SNOW LOADS
EN 27389 : 1990	BUILDING CONSTRUCTION - JOINTING PRODUCTS - DETERMINATION OF ELASTIC RECOVERY
ASTM E 1300 : 2016 : REDLINE	Standard Practice for Determining Load Resistance of Glass in Buildings
ISO 11600:2002	Building construction Jointing products Classification and requirements for sealants
ISO 7390:2002	Building construction Jointing products Determination of resistance to flow of sealants
ISO 9002:1994	Quality systems — Model for quality assurance in production, installation and servicing
EN 572-2:2012	Glass in building - Basic soda lime silicate glass products - Part 2: Float glass
ISO 16269-6:2014	Statistical interpretation of data Part 6: Determination of statistical tolerance intervals
ISO 10563:2017	Buildings and civil engineering works — Sealants — Determination of change in mass and volume
ISO 28278-2:2010	Glass in building — Glass products for structural sealant glazing — Part 2: Assembly rules
EN 572-4:2012	Glass in building - Basic soda lime silicate glass products - Part 4: Drawn sheet glass
ISO 1183-1:2012	Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
ISO 11358-2:2014	Plastics Thermogravimetry (TG) of polymers Part 2: Determination of activation energy
ISO 9001:2015	Quality management systems — Requirements
ISO 9227:2017	Corrosion tests in artificial atmospheres — Salt spray tests
ISO 4892-2:2013	Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
EN 572-5:2012	Glass in building - Basic soda lime silicate glass products - Part 5: Patterned glass
EN 28339 : 1990	BUILDING CONSTRUCTION - JOINTING PRODUCTS - SEALANTS - DETERMINATION OF TENSILE PROPERTIES
EN 1991-1-4:2005/A1:2010	EUROCODE 1: ACTIONS ON STRUCTURES - PART 1-4: GENERAL ACTIONS - WIND ACTIONS
ISO 527-3:1995	Plastics Determination of tensile properties Part 3: Test conditions for films and sheets
ASTM C 1036 : 2016 : REDLINE	Standard Specification for Flat Glass
ASTM C 1376 : 2015 : REDLINE	Standard Specification for Pyrolytic and Vacuum Deposition Coatings on Flat Glass
EN 13022-2:2014	Glass in building - Structural sealant glazing - Part 2: Assembly rules
ISO 868:2003	Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness)
ISO 3231:1993	Paints and varnishes — Determination of resistance to humid atmospheres containing sulfur dioxide
EN 1096-2:2012	Glass in building - Coated glass - Part 2: Requirements and test methods for class A, B and S coatings